As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Tie rods are the links that carry every turn of the steering wheel out to the front wheels. When one wears, the steering feels loose and the tires feather. The best tie rod ends are the correct part number for your car and side, from a maker that explains how the joint is sealed and lubricated.
Below are inner versus outer basics, the major brands and six example listings for the Camry, Civic, Equinox, Silverado 1500 and F-150. If you are still deciding whether a tie rod is really the culprit, start with our rundown of bad tie rod symptoms and what they feel like.
Quick answer
Which tie rod end brand should I buy?
Choose the exact part number for your vehicle, side and position before you choose a brand. MOOG, TRW, Mevotech and Delphi all make solid single ends, and Detroit Axle sells inner and outer kits. Confirm the fit in Amazon’s checker, replace worn rods together and book an alignment straight after.
Our Quick Picks
Three example listings that cover the common jobs: an outer end for the Camry, an inner rod for the Equinox and a full inner and outer kit for the F-150.

MOOG ES800930
A MOOG outer end for the seventh-generation Camry and its Avalon sibling.

MOOG EV800648
A MOOG inner rod for the second-generation Equinox and Terrain.

Detroit Axle 4pc Tie Rod Kit
Both sides, inner and outer, in a single order for the 13th-generation F-150.
Inner Rods, Outer Ends and What Wears Out
On a rack-and-pinion car, each side has two pieces. The inner tie rod screws onto the end of the steering rack and hides under a rubber bellows boot. The outer tie rod end threads onto the inner rod, held by a jam nut, and its tapered stud drops into the steering knuckle.
Both are ball-and-socket joints that wear once grit gets past a split boot. The outer end usually goes first because it lives in road spray. Solid-axle trucks use longer rods and adjusting sleeves instead.
When you compare listings, look at these details:
- Position: inner or outer, and left or right.
- Bearing design: polymer bearings run quietly, while sintered or powdered-metal bearings are meant to resist wear and pass grease.
- Sealed or greasable: a fitting lets you flush old grease and moisture out; a sealed joint needs nothing but a sound boot.
MOOG lays out the features of its own outer and inner rods on the MOOG tie rod ends page, including its gusher bearing, heat-treated studs and greaseable socket. Not every part number gets every feature.
MOOG vs Delphi, TRW and the Rest of the Shelf
The question that comes up most on forums is MOOG versus Delphi, or MOOG versus a store brand. Owners report long life and early failures from almost every name, so installation and road conditions matter as much as the logo. The best tie rod ends are simply a correct part from a known maker, torqued properly and aligned afterward.
MOOG (DRiV) is known for greasable Problem Solver designs, and TRW (ZF) supplies factory steering parts. Mevotech offers TTX and Supreme lines with grease fittings, Delphi focuses on OE-style sealed ends, ACDelco covers GM vehicles first, and Detroit Axle bundles inner and outer rods into kits.
Best Tie Rod Ends for Popular Cars and Trucks: The Picks
Each part number below is an example for the vehicle its Amazon listing names. Another year, trim or side can take a different number, so check Amazon’s fit checker first.
1. MOOG ES800930: Outer Steering Tie Rod End for 2012-2017 Camry

- Outer tie rod end, sold singly
- Listing names 2012-2017 Camry
- Also lists 2013-2018 Toyota Avalon
- Opposite side is MOOG ES800931
MOOG ES800930 is an outer steering tie rod end, and its Amazon listing names the Toyota Camry from 2012 to 2017 along with the 2013 to 2018 Avalon. Treat it as an example part number for a very common sedan. The opposite side has its own number, MOOG ES800931, so a two-sided job takes one of each.
MOOG is part of DRiV, and the listing describes this end as a steering component built to support accurate wheel movement and consistent response, with protective features against road debris, moisture and contaminants. MOOG explains its wider outer tie rod features, such as heat-treated studs and the pressed-in cover plate, on its own site, but those are application specific. Look at the listing photos and the box contents for the nut, cotter pin and any grease fitting before you start.
This end suits owners keeping a high-mileage Camry or Avalon on the road who want a widely stocked replacement brand. A worn outer end on these cars tends to show up as a clunk over rough pavement or a steering wheel that needs constant small corrections. Confirm your year, model and engine in Amazon’s fit checker, and plan on an alignment once it is in.
2. TRW JTE1730: Left Outer Tie Rod End for 2012-2015 Civic and ILX

- Left outer tie rod end, sold singly
- Listing names 2012-2015 Civic
- Also lists 2013-2019 Acura ILX
- 500K-cycle endurance testing per TRW
TRW JTE1730 is a left outer tie rod end, and its Amazon listing names the Honda Civic from 2012 to 2015 and the Acura ILX from 2013 to 2019. That covers the ninth-generation Civic. The right side is a separate part, TRW JTE1728, so treat this as an example number and order the matching side if both ends are worn.
TRW, now part of ZF, says every part goes through four levels of testing and technical review before approval, including endurance testing of 500,000 cycles. The listing also points to long-lasting rubber dust covers and OE-quality materials that meet or exceed original equipment standards. It suits drivers who want a factory-style sealed end rather than a grease fitting.
It suits Civic and ILX owners who keep their cars for many years and want a replacement close to the original design. A loose outer end on these compact cars can feel like vagueness on center or a light knock when you turn into a driveway. TRW’s own listing asks buyers to use Amazon’s check-fit tool, so enter your exact year, trim and engine before you buy.

3. MOOG EV800648: Inner Steering Tie Rod for 2010-2017 Equinox and Terrain

- Inner tie rod, sold singly
- Listing names 2010-2017 Equinox
- Also lists 2010-2017 GMC Terrain
- Threads onto the steering rack
MOOG EV800648 is an inner tie rod, the piece that threads onto the end of the steering rack under the rubber bellows boot. Its Amazon listing names the 2010 to 2017 Chevrolet Equinox and the 2010 to 2017 GMC Terrain. It is our example inner rod, since shoppers often replace only the outer end when the play is further in.
The listing describes the rod as a critical steering part that supports accurate wheel movement, with protective features against debris and moisture and a goal of returning steering feel close to original equipment. MOOG’s general inner rod features, such as wrench flats and pre-applied thread locker, are explained on its site but vary by part number. Check whether a new boot and clamps come in the box, because the old boot usually tears during removal.
This rod suits Equinox and Terrain owners who have found play at the rack while squeezing the boot and rocking the wheel. Removing an inner rod usually takes an inner tie rod tool, so plan for that or leave the job to a shop. Engine and drivetrain can change the part, so confirm your year and engine in Amazon’s fit checker, then have the toe set afterward.
4. Mevotech TTX TXES3493T: Greasable Outer Tie Rod End with Sintered Bearing

- Outer tie rod end, sold singly
- Replaces GM 12471376, 19149617, 26059226
- 180-degree SAE grease fitting
- Slotted castle nut and snap cotter pin
Mevotech TTX TXES3493T is an outer steering tie rod end. Its Amazon listing gives GM part numbers 12471376, 19149617 and 26059226 rather than vehicle names. It shares a number with MOOG ES3493T, which MOOG’s own listing names for the 1999 to 2006 Chevrolet Silverado 1500, so treat that as a cross-reference and an example. Drivetrain and model year change the linkage on these trucks, so check yours in Amazon’s fit checker before ordering.
The TTX line is built around maintenance. The listing describes patented sintered bearings for longer wear, a patented sealing ring that locks the boot onto the housing, a 180-degree SAE grease fitting, and a part-specific slotted castle nut with an easy-snap cotter pin. Pre-applied Nylok thread adhesive helps keep the fasteners from loosening with vibration.
This end suits truck owners who are happy to grease the front end at every oil change, which helps push out salt water before it can rust the socket. It is less suited to someone who never touches a grease gun, because the benefit of the fitting depends on using it. As with any outer end, count the threads on the old one and book an alignment afterward.
View Mevotech TTX TXES3493T on Amazon

5. Delphi TA2995: OE-Style Outer Tie Rod End with Precision-Machined Stud

- Outer tie rod end, sold singly
- Replaces Toyota 45460-09050, 45460-39635
- Cross-references MOOG ES80602 and ES80603
- Fatigue tested, fitting accessories included
Delphi TA2995 is an outer tie rod end, and its Amazon listing gives the Toyota numbers 45460-09050 and 45460-39635 along with cross-references including MOOG ES80602 and ES80603. MOOG’s own listings name those parts for the 2004 to 2011 Camry, 2004 to 2006 Lexus ES330 and 2004 to 2008 Solara. The Delphi listing does not name vehicles itself, so treat the Camry as an example and confirm fit before you buy.
Delphi is an original-equipment supplier, and the listing says its ball studs are machined to micron tolerances for durability and smooth joint movement. It also says the tie rods are fatigue tested and that the necessary accessories for a complete job are included, with a protective finish applied to each part. The listing adds that Delphi’s own limited warranty does not apply to Amazon purchases, so any cover comes from the seller.
This end suits owners who want a sealed, factory-style replacement and answer the common question of MOOG vs Delphi by choosing the simpler design. It makes sense for an older Camry with plenty of life left. Since one listing can cover two sides or only one, check the position notes in Amazon’s fit checker for your exact year and model.
6. Detroit Axle 4pc Front Tie Rod Kit: Inner and Outer Ends for 2015-2020 F-150

- 2 inner and 2 outer tie rod ends
- Listing names 2015-2020 F-150, not Raptor
- Also lists 2015-2021 Expedition, Navigator
- 10-year warranty per listing
This Detroit Axle kit includes two inner and two outer front tie rod ends, which covers both sides of the steering linkage in one order. Its Amazon listing names the 2015 to 2020 Ford F-150, excluding Raptor models, plus the 2015 to 2021 Ford Expedition and Lincoln Navigator. It is our example of the full-kit approach.
Detroit Axle says its suspension parts go through impact, wear and fatigue testing, and the listing states a 10-year warranty. A kit like this saves you from matching four separate part numbers, and it means every joint on the steering side starts fresh at the same time. Check whether boots come in the box, because this listing names only the four rods.
The kit suits F-150 owners with high mileage who have found play at more than one joint, or who want to refresh the linkage while the truck is already apart for other front-end work. It is more than you need if only one outer end is loose on a newer truck. Cab, drivetrain and build date can matter on these trucks, so confirm your exact year and configuration in Amazon’s fit checker, and get the truck aligned once all four are in.
View Detroit Axle 4pc Tie Rod Kit on Amazon
Matching Each Listing to Your Vehicle
This table sums up the best tie rod ends in this guide by reference vehicle and position, so you can jump to the brand line that covers your car.
| Reference vehicle | Example listing | Position | Good fit for |
|---|---|---|---|
| Camry 2012-2017 | MOOG ES800930 | Outer, one side | Commuter sedans with miles to go |
| Civic 2012-2015 | TRW JTE1730 | Outer, left | Owners who want an OE-style sealed end |
| Equinox 2010-2017 | MOOG EV800648 | Inner | Play found under the rack boot |
| Silverado 1500 1999-2006 (cross-reference) | Mevotech TTX TXES3493T | Outer | Trucks you plan to grease |
| Camry 2004-2011 (cross-reference) | Delphi TA2995 | Outer | Older Toyotas kept for the long run |
| F-150 2015-2020 | Detroit Axle 4pc kit | Inner and outer, both sides | Doing the whole linkage at once |
Single ends are sold one at a time, so plan for the opposite side as well. On a high-mileage car, the inner rod is often tired too.

Salt, Potholes and Steering Wear in Grand Rapids
Our winters are hard on steering joints, and even the best tie rod ends wear quickly once a boot splits. Brine soaks the boots, freeze-thaw cycles crack old rubber, and once water gets into the socket the joint rusts from the inside. A greasable end lets you flush it out, if someone actually does.
Spring potholes are the other enemy. A hard hit can bend a tie rod and throw the toe off. Our checklist of pothole damage signs to look for covers the steering and suspension checks worth doing after a bad one.

Not every front-end knock is a tie rod. Ball joints wear in a similar pattern, so see our guide to the best ball joints for common cars and our roundup of shocks and struts for daily drivers, since tired struts make loose steering feel worse.
Fitting New Tie Rods and When to Call Us
This is a steering job, so treat it as safety work. Support the car on stands, count the turns as you remove the old outer end so the new one goes on close to the same length, and torque every nut to the factory figure before fitting a new cotter pin.

New tie rods change the toe setting the moment they go in, so an alignment is not optional. Skip it and the car can pull or chew through a new tire. If the steering also feels heavy, our article on a steering wheel that is hard to turn covers other causes.
If the inner rod is seized to the rack, the threads are rusted solid or you would rather not do steering work at home, let us take a look. We handle suspension and steering repair in Grand Rapids on foreign and domestic vehicles, including the alignment check after new parts go in.
More Buying Guides
Frequently Asked Questions
Is MOOG or Delphi better for tie rod ends?
Neither wins every time. MOOG often adds a grease fitting and its own bearing design, while Delphi sells OE-style sealed ends. Pick the correct number for your car from either brand, install it carefully and have the alignment set.
Should I replace inner and outer tie rods together?
Not always, but it often makes sense on a high-mileage car. Check the inner rod for play with the boot squeezed. If it is loose too, replacing both at once means a single alignment.
What grease should I use on greasable tie rod ends?
Use a chassis grease that meets the spec in your owner’s manual. Pump slowly and stop when the boot just starts to swell.
Do I need an alignment after replacing a tie rod end?
Yes. The tie rod sets the toe angle, so even a careful thread count only gets close. An alignment keeps the car tracking straight and protects your tires.
Steering feeling loose, or the car drifting in its lane? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a steering inspection through our contact page.
Tied up during shop hours? Our after-hours drop-off is open to you, so bring the car to 456 Carrier St NE in Creston with a note on when the looseness shows up.
