456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Worth It for One Bearing? An Orion Motor Tech Wheel Bearing Press Kit Review

orion motor tech wheel bearing press kit review: close-up of a busy industrial workshop featuring machinery and tools

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

The blue-cased OMT kit turns up in nearly every search for a home bearing press, and most buyers want one answer before ordering: will it pull the bearing out of my knuckle? This orion motor tech wheel bearing press kit review looks at what the 24 piece set is designed for, where it runs out of strength, and four similar kits to compare it against.

If you haven’t confirmed the bearing is the culprit, start with our rundown of wheel bearing noise symptoms. A worn tire or a dry CV joint can sound similar, and no press kit fixes either one.

Quick answer

Is the Orion Motor Tech wheel bearing press kit worth buying?

For press-in cartridge bearings on most front-wheel-drive cars and light trucks, yes. The OMT 24pc kit uses two 8.8 grade sliding screws and lets the knuckle and strut stay on the car. It won’t help with bolt-on hub assemblies, and a heavily rusted bearing may need a stronger screw or a shop press.

Our Quick Picks

Three quick picks: the OMT 24pc set this review centers on, a kit that prints its adapter sizes in inches and one with a full millimeter drift chart. All five kits are covered below.

OMT 24pc Press Kit product photo
Reviewed kit

OMT 24pc Press Kit

24 pieces · FWD press-in bearings

The standard OMT on-car sleeve kit in a blue case.

SuitsFront-wheel-drive cars and light trucks
View on Amazon →
Punmew 24pcs Kit product photo
Listed inch sizes

Punmew 24pcs Kit

24 pieces · 0.75 in screw

Prints every adapter size and the screw dimensions.

SuitsOwners who measure in inches
View on Amazon →
WINMAX 23 Pcs Kit product photo
Full drift chart

WINMAX 23 Pcs Kit

23 pieces · 55 to 88 mm drifts

Lists each of its twelve drift diameters.

SuitsFWD cars and small trucks
View on Amazon →

What the OMT 24pc Set Is Designed to Do

Orion Motor Tech sells this set as an on-car tool for front-wheel-drive bearings. Instead of pulling the steering knuckle and taking it to a hydraulic press, you thread a long screw through the hub, stack a sleeve on one side and a bushing on the other, then tighten a nut until the bearing slides out of its bore.

The same hardware runs in reverse to seat the new bearing and then the hub flange, with no hammer and no bench press.

  • Made for: sealed press-in cartridge bearings held in the knuckle by a snap ring, which many front-wheel-drive cars and some light trucks use up front.
  • Not made for: bolt-on hub assemblies, which come out with a puller or slide hammer, or older tapered roller bearings that drop out once the rotor and hub are off.

Your parts catalog settles it: a plain bearing ring means a sleeve kit like this, while a flange with bolt holes and a sensor plug means a different tool.

Checking Fit Before the Kit Arrives

The OMT listing promises sleeves and bushings in the most common sizes but doesn’t print the diameters in its bullet points. Some rivals do, which makes them easier to match against a specific bearing. Either way, measure the outside diameter of the new bearing and the hub’s pilot before you order, and compare them with the photos and any size chart the seller provides.

Getting the stack right matters as much as the size. A Timken walkthrough on press-in wheel bearings says the installing adapter must push on the bearing’s outer race, and the inner race needs support when the hub goes back in. It also suggests a paper clip test to find the magnetic encoder seal, which faces inboard toward the wheel speed sensor.

  • Clean the bore with a file, emery cloth or wire brush by hand. A power grinder can open up the seat and let the new bearing spin.
  • Grease the screw threads every time, as OMT’s own listing advises.
  • Fit the new snap ring before pressing the hub flange back in.

Orion Motor Tech Wheel Bearing Press Kit Review and Four Alternatives

The OMT set comes first, followed by four other front-wheel-drive sleeve kits of the same type. Every spec below comes from the Amazon listing for that kit, so compare sizes there with your own bearing.

1. Orion Motor Tech OMT 24pc: FWD Wheel Bearing Press Kit with Sliding Screws

OMT 24pc Press Kit product photo
Key features
  • 24 pieces: sleeves, bushings and sliding screws
  • Two heat-treated 8.8 grade screws
  • Knuckle and strut stay on the vehicle
  • Blow-molded storage case

This is the kit most buyers mean when they search for the Orion Motor Tech bearing press. The 24 piece set covers removal and installation of press-in front wheel bearings without a hammer, and the listing says it works with nearly any front-wheel-drive car or light truck, foreign or domestic. The sleeves and bushings come in the most common sizes, though the exact diameters are left to the product photos.

The two sliding screws are rated grade 8.8, heat treated and blackened for strength and corrosion resistance, and the listing describes the rest of the hardware as stainless steel. Because the screw pulls the bearing straight through the knuckle, the strut assembly and steering knuckle stay on the car, which OMT says avoids a front-end alignment. Orion also asks owners to lubricate the rod, a sensible step that protects the threads under load.

Everything packs into a blow-molded case, so the pieces stay sorted between jobs. It suits a home mechanic replacing a press-in bearing on a common front-wheel-drive car. It does not suit bolt-on hub units, and a bearing fused into a corroded knuckle may call for a heavier screw or a shop press.

View OMT 24pc Press Kit on Amazon

2. DAYUAN 24pcs FWD Bearing Removal Tool: 55 to 88 mm Drifts with 8.8 Grade Screws

DAYUAN 24pcs Kit product photo
Key features
  • 32 mm and 38 mm drive shafts
  • Drift sizes from 55 mm to 88 mm
  • Two 8.8 grade sliding screws
  • Carbon steel with black oxide coating

DAYUAN’s 24 piece kit is a direct match for the OMT layout, with one practical difference: the listing spells out its range. It includes drive shafts of 32 mm and 38 mm and drift sizes running from 55 mm to 88 mm, which gives you something concrete to compare against the outside diameter of your new bearing before you order.

Two grade 8.8 sliding screws do the pressing, and DAYUAN says their precision threads hold securely while you turn them. The pieces are heavy-duty carbon steel with a black anodic oxidation coating that the maker describes as rust resistant. As with other on-car kits, the steering knuckle and strut stay assembled, so the listing says no front-end alignment is needed after the work. A heavy plastic case holds the set for storage and transport.

This kit suits someone who likes to check sizes against a parts catalog before buying, since the metric range is right on the listing. It covers most front-wheel-drive cars and small trucks. It is not a tool for bolt-on hub assemblies or tapered bearings, and like any standard-grade screw kit it benefits from grease on the threads and patience on a rusty knuckle.

View DAYUAN 24pcs Kit on Amazon

detailed view of mechanical components in an industrial setting

3. Punmew 24pcs Wheel Bearing Press Kit: 2.19 to 3.47 Inch Adapters, 0.75 Inch Screw

Punmew 24pcs Kit product photo
Key features
  • Adapter sizes 2.19 to 3.47 inches listed
  • 7.5 x 0.75 inch screw
  • Grade 8.8 heat-treated sliding screws
  • Blow-molded storage case

Punmew lists more dimensions than most kits in this class. The adapter sizes run 2.19, 2.50, 2.63, 2.78, 2.83, 2.87, 2.90, 2.94, 3.05, 3.20, 3.29 and 3.47 inches, and the screw measures 7.5 inches long by 0.75 inches in diameter. If your bearing catalog gives sizes in inches, that list makes a quick fit check possible.

The sliding screws are grade 8.8 with precision threading, heat treated and blackened for strength and corrosion resistance. Punmew describes the set as premium stainless steel and says it removes and installs bearings without hammering or affecting alignment, with the steering knuckle and strut assembly left untouched. The listing claims compatibility with almost any front-wheel-drive car or light truck, foreign or domestic, and the 24 pieces pack into a blow-molded case for the garage or the shop.

This one suits a careful buyer who wants to match a bearing diameter before the box arrives. The 0.75 inch screw is the usual size for this type of kit, so it shares the same limits as its rivals on a badly seized bearing. It is meant for press-in cartridge bearings, not bolt-on hub units.

View Punmew 24pcs Kit on Amazon

4. DNA Motoring TOOLS-00715: 24pcs Front Wheel Bearing Press Kit with 13 Bushings

DNA Motoring TOOLS-00715 product photo
Key features
  • Part number TOOLS-00715
  • 13 bushings, 4 sleeves, 2 sleeve plates
  • Two 8.8 grade sliding screws
  • Heavy-duty plastic storage case

DNA Motoring sells this 24 piece press kit under part number TOOLS-00715, and the listing is specific about what’s inside: 13 bushings, 4 sleeves, 2 sleeve plates and two grade 8.8 sliding screws. That breakdown helps if you have used a sleeve kit before and want to know the stack options available before you start.

The 13 bushing sizes are meant to cover almost any front-wheel-drive vehicle, and DNA says the kit suits most domestic and import front-wheel-drive cars and trucks. The pieces are carbon steel with a finish described as corrosion and rust resistant, and the maker points to wear resistance for long service life. A heavy-duty plastic case keeps the set organized, which matters with this many similar-looking bushings to sort through mid-job.

This kit suits a home mechanic who wants a clear parts count and a part number to reference. Like the others here, it presses sealed cartridge bearings in and out of the knuckle on the car. It does not handle bolt-on hub assemblies, and the listing doesn’t print the bushing diameters, so compare your bearing against the product images before ordering.

View DNA Motoring TOOLS-00715 on Amazon

detailed view of industrial machinery

5. WINMAX Tools Automotive 23 Pcs: FWD Bearing Adapter Kit with 12 Drift Sizes

WINMAX 23 Pcs Kit product photo
Key features
  • 12 drift sizes from 55 mm to 88 mm
  • Steel adapters
  • Knuckle and strut stay assembled
  • Heavy-duty plastic case

WINMAX takes a no-frills approach with a 23 piece adapter kit, and its listing is one of the few that prints every drift diameter. The sizes are 55, 60, 64, 67, 70, 72, 74, 75, 78, 82, 84 and 88 mm. If your replacement bearing’s outside diameter is known, you can see in a moment whether a matching drift is in the case.

The adapters are steel and come in a heavy-duty plastic case. WINMAX says the kit replaces wheel bearings while the steering knuckle and strut assembly stay intact on the vehicle, and that this removes the need for a front-end alignment after the work. The listing names front-wheel-drive cars and small trucks as the intended use, which is the same range as the other kits here.

This set suits a buyer who wants to confirm a single exact bearing size before ordering. The listing gives less detail on the screw itself than the others, so grease the threads, turn it slowly and watch for binding on a corroded knuckle. It is built for press-in cartridge bearings and will not remove a bolt-on hub assembly.

View WINMAX 23 Pcs Kit on Amazon

Our Verdict on the OMT Kit: Pros, Cons and Who Should Buy

Taken on its listing facts, the OMT 24pc is a standard on-car sleeve kit with a tidy case and no unusual extras. For a typical press-in front bearing, that is all the job asks for.

  • Pros: two heat-treated, blackened 8.8 grade sliding screws; a sleeve and bushing range aimed at most front-wheel-drive cars and light trucks, foreign or domestic; on-car work with the knuckle and strut left in place; a blow-molded case that keeps the pieces sorted.
  • Cons: adapter diameters aren’t listed in the bullets; no thrust bearing behind the nut is mentioned, so the threads carry all the friction; grade 8.8 is the usual budget screw rather than a heavy-duty upgrade; it does nothing for bolt-on hub units.

Who should buy it? A home mechanic with one or two front-wheel-drive cars, a breaker bar and a free weekend fits the profile well. Someone working on a salt-belt car with a corroded knuckle, or planning to run the screw with an impact wrench, may want a heavier kit from our best wheel bearing press kit guide. The red-case OMT listing appears to be the same 24 piece kit, so choose either color.

cluttered storage room filled with stacks of rubber belts and industrial equipment

How the Five Sleeve Kits Compare

All five share one layout, so the differences are mostly in how much size detail each listing gives.

KitPiecesSizes on the listingGood fit for
OMT 24pc24Not printed in the bulletsBuyers who want the familiar OMT set
DAYUAN 24pcs2432 and 38 mm shafts, 55 to 88 mm driftsChecking drift sizes in millimeters
Punmew 24pcs24Adapters 2.19 to 3.47 in, 0.75 in screwChecking sizes in inches
DNA Motoring TOOLS-007152413 bushings, 4 sleeves, 2 platesKnowing what’s in the case
WINMAX 23 pcs2312 drift sizes, 55 to 88 mmMatching one exact bearing diameter
OMT wheel bearing press kit and four alternatives compared by listed sizes

If the sizes look equal, the deciding factors are your bearing’s diameter and how comfortable you are with a listing that leaves sizes to the photos. Timken’s free light vehicle TechTips library covers bearing and hub replacement procedures that apply to any of these kits.

close-up view of fire truck compartments filled with essential firefighting tools and equipment

Rusted Knuckles After a Few Michigan Winters

Brine sprayed on West Michigan roads works its way between the bearing’s outer race and the knuckle bore. After several seasons the two can bond so firmly that a standard screw starts to gall before the bearing moves.

Give penetrating oil a night to soak in, turn the nut steadily by hand rather than hammering it with an impact gun, and stop if the threads begin to squeal or bind. Keep torch heat away from the speed sensor and its wiring. Once the bore is empty, inspect it for pitting, because a pitted seat may not hold the new bearing tight.

stylish 3D rendering of a teal metallic gear

When to Hand the Bearing Job to a Shop

Pressing two parts out and two back in on the car is a long job, and mistakes cost money. A bearing pressed in at an angle, a cracked race or a damaged tone ring can bring back the hum or trigger an ABS warning light. Torque the axle nut to the figure in your service manual, and if you removed the knuckle or loosened the strut bolts, get the alignment checked afterward.

Our wheel bearing replacement service in Grand Rapids handles press-in bearings and bolt-on hub units on foreign and domestic vehicles. If a ball joint, tie rod or control arm turns out to be worn at the same corner, our suspension repair team can take care of it during the same visit. For a sense of how long a fresh bearing should go, read how long wheel bearings last.

Frequently Asked Questions

Does the Orion Motor Tech kit work on bolt-on hub assemblies?

No. The OMT 24pc set is built to press sealed cartridge bearings out of and into the steering knuckle. A bolt-on hub assembly unbolts from the knuckle as one unit, so it needs a puller or slide hammer instead of a sleeve kit.

Can I use an impact wrench on the OMT press kit?

The listing describes turning the sliding screws to press the bearing smoothly and asks you to lubricate the rod. A hand ratchet or breaker bar gives you more feel, and slow, steady turns are kinder to standard 8.8 grade threads than hammering them with an impact gun.

Is the blue-case OMT kit different from the red-case one?

The two Amazon listings share the same title, piece count and feature list apart from the case color. Check that the piece count still reads 24 before ordering, since OMT also sells a larger 38 piece set with a bearing separator.

What should an orion motor tech wheel bearing press kit review tell me about fit?

It should tell you which bearing type the kit handles and remind you to measure. Compare the new bearing’s outside diameter with the sleeves and bushings shown on the listing, and confirm your year, model and drivetrain in the parts catalog before you start.

Bearing still humming after a weekend with the press kit, or would you rather skip the job altogether? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a bearing inspection on our contact page.

Busy until we close? Roll the car up to 456 Carrier St NE after hours, leave the keys in our drop-off with a note about which corner hums, and we’ll call once it’s been looked at.