456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Low Nose, Heavy Front: Choosing the Best Floor Jack for Dodge Cars and SUVs

best floor jack for dodge: beautiful wooden cabinet with sleek handles and natural wood grain

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Charger or Challenger has a long, low nose and a lot of weight over the front wheels, and a Durango in the same driveway sits several inches higher. That spread is why picking the best floor jack for Dodge owners is less about raw tonnage and more about how low the jack starts and how high it finishes.

Below we cover what these cars ask of a jack and how to measure clearance, then review six jacks whose listings fit Dodge muscle cars and, in some cases, the Durango. For a wider look at jacks for any low car, see our low profile floor jack roundup.

Quick answer

Which floor jack suits a Dodge Charger or Challenger?

Choose a 3 ton low profile jack that starts near 3 inches and reaches about 20 inches, such as the Bonnlo 3 Ton, which covers a Charger nose and a Durango. For an all-steel jack with stated ANSI/ASME PASE compliance, the AV Steel Low Profile 3 Ton fits well.

Our Quick Picks

Three places to start: one jack that covers a Charger and a Durango, an all-steel low profile pick, and a lighter hybrid you can carry. All six are reviewed below.

Bonnlo 3 Ton product photo
Widest range

Bonnlo 3 Ton

3 ton · 2.95 to 20.1 in.

Starts under 3 inches and still climbs past 20.

SuitsA Charger and a Durango in one garage
View on Amazon →
AV Steel Low Profile 3 Ton product photo
Standards-listed steel

AV Steel Low Profile 3 Ton

3 ton · 3-1/8 to 19-7/8 in.

All-steel low profile jack with stated ANSI/ASME PASE compliance.

SuitsCharger and Challenger garages
View on Amazon →
VEVOR 3 Ton Racing Jack product photo
Lighter hybrid

VEVOR 3 Ton Racing Jack

3 ton · 3-6/11 to 19-11/16 in.

Aluminum and steel jack with side carry handles.

SuitsOwners who move the jack often
View on Amazon →

What a Dodge Muscle Car Demands From a Jack

Most Dodge owners who shop for a floor jack drive a Charger or Challenger. Both are large, heavy rear-drive or all-wheel-drive cars, and the V8 and supercharged versions add weight right where you want to lift. Many also wear front splitters, chin spoilers or aftermarket lowering springs that leave very little room under the bumper.

The newer generation changes the picture again. Dodge’s current Charger page lists two-door and four-door bodies and the 3.0L SIXPACK twin-turbo straight-six, with all-wheel drive standard on the Scat Pack. Whatever the year, the owner’s manual shows the approved jacking points, and those are the only places the saddle should go.

  • Low entry: a minimum saddle height near 3 to 3.5 inches lets the jack roll under a low nose without lifting one side first.
  • Capacity margin: you only lift one end or one corner, but a 3 ton rating leaves room for a heavy front end.
  • Reach: a long frame helps the saddle get past the bumper to a subframe or approved pinch weld point.

Clearance First: Sizing a Jack to Your Charger, Challenger or Durango

Before you compare models, park on a flat floor and measure from the concrete to the lowest point of the front bumper or splitter. Then measure to the lift point you plan to use. The first number tells you how low the jack must start, and the second, plus a few inches for suspension droop, tells you how high it must climb.

Owners often report that the front of a lowered Challenger or Charger is too tight even for some low profile jacks, so they lift one side first or roll onto thin boards. A jack that starts near 3 inches usually removes that step. A Durango has the opposite problem, so a jack that tops out near 15 inches may fall short.

When you pick the best floor jack for Dodge work, remember that it only raises the car. Rated jack stands under the frame or subframe hold it while you work, and our guide to basic car maintenance tools covers stands, wheel chocks and the other garage basics.

Best Floor Jack for Dodge: Six Jacks Reviewed

Lift ranges below come from each Amazon listing. Measure your own car first, since splitters, lowering kits and tire sizes change the clearance you actually have.

1. Bonnlo 3 Ton Low Profile Floor Jack: Dual Pump Hydraulic Jack with 2.95 to 20.1 in. Range

Bonnlo 3 Ton product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 2.95 to 20.1 in. listed lifting range
  • Dual piston pump
  • 360 degree swivel front casters

The Bonnlo 3 Ton Low Profile Floor Jack is a horizontal hydraulic trolley jack rated at 6,600 pounds. Its listing gives a lifting range from 2.95 inches to 20.1 inches, which is the broadest span of any jack reviewed here. Bonnlo describes it for sedans, SUVs and MPVs, and positions it for both home garages and repair shops.

The lifting side uses a dual piston pump, which raises the saddle in fewer strokes than a single-piston design and gets it to the lift point quickly. The maker describes a heavy-duty structure meant to hold steady without wobbling once the load is on the saddle. Swivel casters at the front turn a full 360 degrees, and a sturdy handle helps you steer and position the jack under the car.

For a Dodge household, the appeal is coverage. A start under 3 inches slides beneath most Charger and Challenger noses, including many with a chin spoiler, and the 20 inch finish reaches the lift points on a stock Durango. That makes it a sensible single jack when a muscle car and an SUV share the driveway.

View Bonnlo 3 Ton on Amazon

2. AV Steel Low Profile Floor Jack: 3 Ton Dual Piston Jack with 3-1/8 to 19-7/8 in. Range

AV Steel Low Profile 3 Ton product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 3-1/8 to 19-7/8 in. listed lift range
  • Dual piston quick lift pump
  • Meets ANSI/ASME PASE, 12-month warranty

The AV Steel Low Profile Floor Jack is an all-steel trolley jack rated at 3 tons, or 6,600 pounds. Its listing gives a minimum height of 3-1/8 inches and a maximum of 19-7/8 inches, which places it among the lower starting points in this list. The frame measures about 29 by 13-3/4 by 5-7/8 inches, so it is a full-size garage jack rather than a trunk tool.

A dual piston pump raises the saddle with fewer handle strokes than a single-piston design, which helps when the car is heavy at the nose. An overload protection valve limits the jack to its rated load, and the saddle rotates 360 degrees so you can line it up with a subframe point without shifting the whole frame. The maker states compliance with ANSI/ASME PASE and offers a 12-month warranty.

For a Charger or Challenger with a chin spoiler or lowering springs, that 3-1/8 inch start is the main reason to pick it. The near 20 inch finish also reaches a stock Durango’s lift points. Because it is steel, it is heavy to carry, so it suits a garage more than a car trunk.

View AV Steel Low Profile 3 Ton on Amazon

aerial shot of lush green valleys with winding roads and river view

3. VEVOR 3 Ton Low Profile Racing Floor Jack: Aluminum and Steel, 3-6/11 to 19-11/16 in.

VEVOR 3 Ton Racing Jack product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 3-6/11 to 19-11/16 in. listed range
  • Dual pump, full height in 7 strokes
  • Two-piece 45 in. handle, rubber saddle

The VEVOR 3 Ton Low Profile Racing Floor Jack pairs heavy-duty steel with aluminum so it stays sturdy while weighing less than an all-steel jack of the same rating. It carries a 6,600 pound capacity, and the listing gives a minimum height of 3-6/11 inches, about 90 millimeters, and a maximum of 19-11/16 inches, about 500 millimeters.

VEVOR says the dual parallel pump reaches full height in seven strokes. The 45 inch handle gives good leverage, splits in two for storage and has a foam bumper to protect paint. A rubber saddle rotates 360 degrees and can be replaced, while two universal rear casters and side armrests make the jack easy to roll, carry and place. The maker lists CE and UKCA certification, the ASME PALD-2014 standard and a built-in load limiter.

For a Charger or Challenger owner who carries the jack between a garage and a driveway, the lighter build and side handles are useful. The 3-1/2 inch start fits under many stock fronts, and the near 20 inch top handles muscle cars and many SUVs. Measure your clearance before you buy if the car wears a splitter.

View VEVOR 3 Ton Racing Jack on Amazon

4. antlevix Heavy-Duty 3-Ton Floor Jack: Steel Low Profile Jack, 2.9 to 19.8 in. Lift

antlevix 3-Ton Steel product photo
Key features
  • 3 ton (6,600 lb) capacity
  • 2.9 in. minimum, 19.8 in. maximum height
  • Dual piston quick lift pump
  • Heavy-duty steel, 62 lb item weight

The antlevix Heavy-Duty 3-Ton Floor Jack is a steel low profile jack rated at 6,600 pounds. Its listing specifications give a minimum height of 2.9 inches, the lowest starting point among these six, and a maximum height of 19.8 inches. The listed item weight is 62 pounds, which tells you this is a solid garage jack rather than something you carry in a trunk.

The frame is built from heavy-duty steel with a wide base, which the maker says improves stability during lifting. A dual piston pump brings the vehicle up with fewer strokes than a standard single-pump jack, useful when you are rotating tires on all four corners or doing a brake check on both axles. The maker aims it at cars, SUVs and light trucks, and mentions sports cars and modified vehicles with minimal ground clearance as a particular fit.

For a Charger or Challenger on lowering springs, or one with a deep front splitter, that 2.9 inch start may let you skip the boards and the side-lift workaround. The near 20 inch top also covers stock SUV lift points. The weight is the trade-off: plan to roll it rather than carry it far.

View antlevix 3-Ton Steel on Amazon

vintage cabinet with floral design next to an indoor plant on a wooden stand

5. TONEIDER 3 Ton Racing Floor Jack: Aluminum and Steel Hybrid with 3.35 to 18.5 in. Lift

TONEIDER 3 Ton Hybrid product photo
Key features
  • 3 ton capacity (6,000 lb listed)
  • 3.35 to 18.5 in. listed lift range
  • Dual piston quick lift pump
  • Aluminum frame, reinforced steel lift arm

The TONEIDER 3 Ton Low Profile Racing Floor Jack uses a lightweight aluminum frame with a reinforced steel lifting arm. The listing gives a lift range of 3.35 inches to 18.5 inches and describes the capacity as 3 tons, quoting 6,000 pounds in the feature text. It is pitched at sedans, SUVs and light trucks in a home garage or a workshop.

A dual piston pump is meant to bring the saddle up to the load in only a few pumps, which saves time on tire rotations and brake jobs. Swivel casters and an ergonomic handle make it easier to aim the saddle at a pinch weld or subframe point without dragging the jack sideways. The hybrid build keeps it easier to move than an all-steel jack.

For a stock Charger or Challenger, the 3.35 inch start slips under most fronts, and the hybrid frame is easy to carry from a shelf to the car. The 18.5 inch finish is a little short for a Durango with soft suspension, so a Dodge owner with an SUV may prefer one of the taller jacks in this list.

View TONEIDER 3 Ton Hybrid on Amazon

6. Big RED T825051 Torin Low Profile Floor Jack: 2.5 Ton Steel Jack with Quick Lift Pump

Big RED T825051 2.5 Ton product photo
Key features
  • 2.5 ton (5,000 lb) capacity
  • 3-3/8 to 14-15/16 in. listed lift height
  • Safety bypass prevents overloading
  • Built-in carrying handle, 1-year warranty

The Big RED T825051 from Torin is a compact steel trolley jack rated at 2.5 tons, or 5,000 pounds. Its listing gives a minimum lifting height of 3-3/8 inches and a maximum of 14-15/16 inches. Torin states plainly that it is ideal for most cars and not recommended for SUVs and trucks, so it belongs in a garage that only holds a Charger or Challenger.

The jack is built from heavy-duty steel and uses a single piston quick lift pump to bring the saddle to the load. A safety bypass system prevents the jack from being pushed past its rated capacity. It rolls on two large steel casters and two 360 degree swivel casters, and a built-in carrying handle makes it simple to pick up and put away.

The low 3-3/8 inch start gets it under most Dodge muscle car noses, and a 2.5 ton rating is enough to lift one end of these cars. The trade-off is the 15 inch top, which limits how far a tire can drop on a car with soft suspension. If a Durango shares the driveway, choose one of the taller jacks above.

View Big RED T825051 2.5 Ton on Amazon

Six Dodge Floor Jacks Side by Side

Use this table to narrow the best floor jack for Dodge cars down to your own clearance numbers. Ranges come from the listings, so check them on Amazon before you order.

JackRated capacityListed lift rangeGood match
Bonnlo 3 Ton3 ton2.95 to 20.1 in.Charger plus a Durango
AV Steel Low Profile3 ton3-1/8 to 19-7/8 in.Low Charger or Challenger nose
VEVOR 3 Ton Racing3 ton3-6/11 to 19-11/16 in.Carrying the jack around
antlevix 3-Ton Steel3 ton2.9 to 19.8 in.Lowered cars, deep splitters
TONEIDER 3 Ton Hybrid3 ton3.35 to 18.5 in.Small garages, tire swaps
Big RED T8250512.5 ton3-3/8 to 14-15/16 in.Cars only, no SUVs
Floor jacks for Dodge cars and the Durango by rated capacity and listed lift range
scenic aerial view of an expansive Welsh valley with winding roads

Cold Garages, Road Salt and Your Jack

In West Michigan, most jack work happens at the spring and fall tire swap, often in an unheated garage. Hydraulic oil gets thick in the cold, so the first strokes can feel slow. OSHA’s rule for jacks also asks that hydraulic jacks exposed to freezing temperatures carry fluid suited to it, and that a raised load be secured right away.

Salt and slush find their way onto the casters and the lift arm. After a winter job, wipe the jack down, let it dry and store it with the saddle fully lowered so the ram stays protected.

lively Paris street scene

When the wheels go back on, tighten the lug nuts in a star pattern and finish with a torque wrench set to the figure in your manual. Our page on the torque wrench for lug nuts walks through that step.

When a Dodge Should Go Up on a Lift Instead

A floor jack and stands handle tire rotations, pad checks and a quick look underneath. Brake rotor changes, suspension parts and anything that needs both axles off the ground are easier to do safely on a two-post lift. If you hear grinding or feel a pulsing pedal, our brake repair service in Grand Rapids can take a look.

vast rocky landscape of Irherm

Routine service is another reason to skip the garage floor. If your Charger, Challenger or Durango is due for the inspections and fluid changes in its maintenance schedule, our factory scheduled maintenance in Grand Rapids covers that work for domestic and foreign vehicles.

Frequently Asked Questions

What is the best car jack for a Dodge Charger?

For most Chargers, a 3 ton low profile floor jack that starts near 3 to 3.5 inches works well, because it rolls under the front without lifting a side first. Confirm the lift points in your owner’s manual and always set jack stands before working underneath.

Why won’t my floor jack fit under my Challenger?

Front splitters, chin spoilers and lowering springs can leave less room than a standard jack needs. Measure the gap under the bumper and pick a jack with a lower minimum height, or drive the front tires onto thin boards to gain clearance.

Is a 2.5 ton jack enough for a Dodge?

A floor jack lifts only one end or corner, so a 2.5 ton unit can handle a Charger or Challenger if its listing allows cars of that size. A 3 ton jack gives more margin, and a Durango is better served by a taller jack made for SUVs.

Can I use one jack for a Charger and a Durango?

Yes, if it starts low enough for the car and climbs high enough for the SUV. Jacks with a range from about 3 to 20 inches, such as the Bonnlo or the antlevix in this list, are the easiest fit for both.

Would you rather keep the creeper in the corner and let us do the lifting? Phone 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday to Friday, or request a time for your Dodge on our contact page.

Busy until evening? Bring the car to 456 Carrier St NE, Grand Rapids, MI 49505 and use our after-hours drop-off, so the Dodge is waiting for us when the shop opens.