As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Ram pickup is a lot of truck to put in the air, and the light jack that lives under a sedan rarely gets the job done. The best floor jack for Ram owners depends on which Ram sits in the driveway: a two-wheel-drive 1500, a leveled 4×4, or a Cummins-powered 2500 or 3500 with a heavy nose.
This guide sorts out capacity and reach for each of those trucks, then reviews six jacks whose listings fit full-size pickups. If you also keep a lower car in the garage, our roundup of low profile floor jacks for cars handles that side of the fleet.
Quick answer
Which floor jack suits a Ram truck?
A stock Ram 1500 is well served by a 4 ton steel jack that reaches about 20 inches, such as the Big RED 4 Ton. Heavy-duty diesel trucks benefit from the extra margin of a 5 ton model, and lifted or leveled 4x4s need a tall off-road jack like the Jack Boss.
Our Quick Picks
Three places to start: a 4 ton garage jack for a stock half-ton, a tall off-road jack for lifted 4x4s and a 5 ton model for heavy-duty diesels. All six get a full review below.

Big RED 4 Ton
Heavy-gauge steel service jack with a quick dual pump.

Jack Boss 3 Ton Off Road
Tall-reach off-road jack that rolls over gravel and dirt.

Maxority 5 Ton
High-capacity steel jack with a long handle for leverage.
Half-Ton, Heavy-Duty or Lifted: Sizing a Jack to Your Ram
Ram builds very different trucks under one badge. A Ram 1500 is a half-ton pickup, while the 2500 and 3500 are heavy-duty trucks, and the diesel versions carry a lot of extra weight over the front axle. Ram’s official Ram 2500 specifications show how far the heavy-duty trucks move away from the half-ton in size and weight.
- Ram 1500, stock height: a 3.5 to 4 ton jack with a maximum height near 20 inches covers most work at the axle or a lower suspension point.
- Ram 2500 and 3500: lean toward 4 or 5 tons, especially under a diesel front end or a truck that carries a plow or a loaded bed.
- Leveled or lifted 4×4: reach becomes the main limit, so look at jacks that pass 25 inches or use stacking extensions.
Lift Points, Reach and Footing
Before you pick the best floor jack for Ram work, find the lift points your owner’s manual approves for your model year. Running boards, step bars and the plastic air dam are never the place for a saddle.
Next, take a tape measure to the truck. Measure from the ground to the lift point you plan to use, then add room for the suspension to drop and for a jack stand to slide in underneath. A jack whose listed maximum falls short of that number will leave the tire touching the floor.
Footing matters as much as numbers. Steel service jacks with small casters roll well on smooth concrete, while big-wheel off-road jacks cope better with blacktop seams and gravel. Whatever you choose, the truck has to rest on rated stands before you get under it, and our beginner’s garage tool list covers stands, chocks and the other basics.
Best Floor Jack for Ram: Six Truck Jacks Reviewed
Every capacity and height below comes from the Amazon listing. Fit depends on your truck, so confirm the lift height against your own Ram, its tires and any leveling kit before you order.
1. Big RED 4 Ton: Low Profile Service Floor Jack with Dual Piston Fast Lift Pump

- 4 ton rated capacity
- Listed lift range of 4 to 20 in.
- Dual pump reaches full height in 9 strokes
- Safety valve, slow lowering, listed as meeting ASME standards
Big RED’s 4 ton service jack is a conventional steel trolley jack sized for pickups, vans and SUVs as well as cars. The listing gives a lifting range from 4 inches up to 20 inches, which means the same jack slides under a lowered car yet still reaches the axle on many stock half-ton trucks. Its frame is made from heavy-gauge steel, and Big RED says it stays balanced at full height and full load.
Speed comes from a dual-pump hydraulic unit that, according to the listing, takes the saddle to maximum height in nine strokes. That saves effort on a truck, where the saddle often travels a long way before the tire clears the floor. A safety valve guards against overload, a slow lowering system lets the truck come down gently, and the maker states that the jack meets ASME safety standards. Two large rear wheels and a pair of 360 degree swivel casters help when you steer it under a bumper.
For a two-wheel-drive or stock-height Ram 1500, this is a sensible all-round garage jack, and the detachable handle helps it fit on a shelf. A 20 inch maximum can fall short on a leveled 4×4, so measure your truck’s lift point before buying.
2. Jack Boss Off Road Jack: 3 Ton Big Wheel Hydraulic Jack with Dual Pumps

- 3 ton rated capacity
- Listed range of 6.14 to 28.98 in.
- Four adjustable lift heights
- Big 360 degree wheels and steel base plate
The Jack Boss off-road jack takes a different approach from a garage service jack. It is rated at 3 tons, and the listing gives a range from 6.14 inches at its lowest to 28.98 inches at the top, set through four adjustable height positions. That reach is the main reason to look at it for a Ram, because leveled and lifted 4×4 trucks often put the axle and frame well above what a 20 inch jack can manage.
Instead of small casters it rides on a pair of large wheels that swivel 360 degrees, and the bottom of the frame is a steel plate designed to sit flat on sand, gravel and rough pavement. Dual pumps shorten the time it takes to reach a tall lift point. The steel body has a corrosion-resistant powder coat, which matters on a truck that sees salted roads, and a side handle makes it easier to carry from the bed to the job.
The trade-off is capacity. Three tons is fine for one corner of a half-ton, but a diesel heavy-duty front end calls for more margin. Check the lift points in your Ram’s manual and confirm the height setting before every lift.
View Jack Boss 3 Ton Off Road on Amazon

3. Maxority 5 Ton: Super Heavy Duty Steel Floor Jack with Dual Piston Quick Lift

- 5 ton (11,000 lb) rated capacity
- Dual piston quick lift pump
- Extra-long handle for leverage
- Overload safety valve and rubber-padded saddle
Maxority’s 5 ton floor jack is built for owners whose trucks make a 3 ton jack feel undersized. The listing rates it at 11,000 pounds, which leaves generous margin under the heavy front end of a Cummins-powered Ram 2500 or 3500, or a truck that wears a plow mount. The body is high-strength steel, aimed at frequent use in a home shop or small workshop.
A dual-piston pump cuts the number of strokes needed to reach working height, and an extra-long handle adds leverage so each stroke takes less effort with a heavy load on the saddle. Safety features listed include an overload valve that stops the jack from lifting beyond its rating, plus an anti-slip saddle with a rubber pad that helps protect the lift point. The listing describes it as low profile but does not state a lift range in its feature bullets.
That missing height figure is the one thing to check before ordering. Look at the full listing or contact the seller for the maximum height, then compare it with a measurement from your truck, especially on a 4×4. Expect a large, heavy jack that prefers a smooth concrete floor over a gravel drive.
4. TCE Hydraulic Floor Jack: 4 Ton Capacity, 3.94 to 20 in. Lift with Dual Quick Lift Pump

- 4 ton (8,000 lb) rated capacity
- Listed range of 3.94 to 20 in.
- Dual pump quick lift
- Overload valve and slow descent
TCE’s blue 4 ton jack covers a wide spread of vehicles from one tool. Its listed minimum height is 3.94 inches and its maximum is 20 inches, so it fits under most cars with modest clearance and still rises to a useful height for a stock pickup. The rated capacity is 8,000 pounds, which gives a half-ton Ram plenty of headroom and suits a lighter heavy-duty truck at the rear axle.
The listing highlights a dual quick-lift pump that it says lifts up to five times faster than a single-pump jack, which helps when the saddle has a long way to climb. A built-in overload valve protects against lifting beyond the rating. The long handle adds leverage, and a slow descent system lets the truck settle gently onto stands instead of dropping when the release is opened.
This jack makes most sense in a two-vehicle household where a Ram shares the garage with a sedan or crossover. Like the other 20 inch jacks here, it may not reach every lift point on a leveled or lifted 4×4, so take a measurement at the truck first and check the manual for approved jacking points.

5. YELLOW JACKET 4 Ton: Low Profile Floor Jack with Dual Pumps and Saddle Pad

- 4 ton (8,800 lb) rated capacity
- Listed range of 4-5/16 to 19-7/8 in.
- Dual pumps for quicker lifting
- Safety valve and detachable handle
The YELLOW JACKET 4 ton jack is a heavy-duty steel floor jack with a listed capacity of 8,800 pounds. Its range runs from a minimum of 4-5/16 inches to a maximum of 19-7/8 inches, so it slips under most cars and reaches the axle on a typical stock half-ton truck. The yellow finish is described as resistant to chipping and cracking, which helps a jack that lives in a damp garage.
Dual pumps raise the saddle faster than a single-pump design, and a built-in safety valve provides overload protection. The listing points to a large saddle surface that spreads contact with the lift point, plus a rubber pad. The handle detaches for storage, and the seller lists a one-year return window, which is worth noting for a tool you may not use every month.
On a Ram, this jack suits routine work on a stock 1500: seasonal wheel swaps, brake pads and a look at the suspension. Its top height is just under 20 inches, so owners of 4×4 trucks on larger tires should measure first. Check the approved lift points in the owner’s manual and set stands before working under the truck.
View YELLOW JACKET 4 Ton on Amazon
6. Blackhawk B6350: 3.5 Ton Fast Lift Service Jack with Swivel Saddle

- 3.5 ton (7,000 lb) rated capacity
- 4 in. swivel saddle
- Internal safety valve and vent plug
- Universal joint for precise load control
Blackhawk’s B6350 is a fast-lift service jack rated at 3.5 tons. The body measures 28-1/2 inches long, 13-3/4 inches wide and 6-1/2 inches high, so it takes up less room than many long-reach garage jacks. That compact length helps in a single-car garage where a full-size Ram already leaves little space to work around.
The saddle is 4 inches across and swivels, which makes it easier to line up with a lift point without moving the whole jack. An internal safety valve and vent plug are part of the hydraulic system, and the listing names a rugged universal joint for precise load control, which helps when you lower a heavy truck. The listing also reminds buyers that the jack is meant to lift a load, not to hold it, and that rated jack stands should go under the vehicle right after lifting.
The listing does not state a lift range, so check the maker’s details or the full listing for maximum height before you rely on it for a 4×4. It makes most sense for a stock half-ton Ram, where 3.5 tons is enough for one corner.
View Blackhawk B6350 on Amazon
Ram Truck Jacks Side by Side
Use this table as a shortlist, then check the listing for the current specification.
| Jack | Listed capacity | Listed lift range | Good match for |
|---|---|---|---|
| Big RED 4 Ton | 4 ton | 4 to 20 in. | Stock Ram 1500 in a paved garage |
| Jack Boss Off Road | 3 ton | 6.14 to 28.98 in. | Leveled or lifted 4×4, gravel |
| Maxority 5 Ton | 5 ton | Not stated | Diesel 2500 and 3500 |
| TCE 4 Ton | 4 ton | 3.94 to 20 in. | Ram and a lower car in one garage |
| YELLOW JACKET 4 Ton | 4 ton | 4-5/16 to 19-7/8 in. | Stock 1500 brake and tire jobs |
| Blackhawk B6350 | 3.5 ton | Not stated | Half-ton trucks, compact storage |
Owners searching for the best floor jack for Ram 2500 or 3500 trucks should read the capacity column first and the height column second. Owners of a 4×4 1500 on bigger tires should read it the other way around.

Ram Tire Season on a West Michigan Driveway
Most Ram owners around Grand Rapids reach for a jack twice a year, swapping between winter and summer wheels. Pick a flat, hard spot, set the parking brake, shift into park and chock the wheel diagonally across from the corner you raise. On gravel, a square of thick plywood under the jack and each stand keeps them from sinking.
Cold affects hydraulics. Hydraulic oil thickens in an unheated January garage, so the first strokes may feel sluggish. Wipe salt and slush off the casters and pump when the job is done.

The Car Care Council’s free Car Care Guide is a handy reminder of what to look at while the wheels are off: brake pads, tire wear, hoses and suspension parts.
When a Lift Beats a Floor Jack
A jack and a pair of stands are fine for tires, pads and a look underneath. Ball joints, tie rods, wheel bearings and anything that needs both axles off the ground are quicker and safer on a vehicle lift. If your Ram clunks over bumps or wanders on the highway, our suspension repair service in Grand Rapids can find the worn part.

Heavy-duty trucks also run through brakes and fluids faster when they tow. Our factory scheduled maintenance service follows the intervals Ram lists for your truck, and rotors or calipers that go beyond a pad swap can go to our brake repair technicians. For a jack sized to other pickups too, see our guide to floor jacks for trucks.
More Buying Guides
Frequently Asked Questions
Is a 3 ton floor jack enough for a Ram 1500?
For raising one corner or one end of a stock Ram 1500, a 3 ton jack can do the job, since it never carries the full weight of the truck. A 3.5 or 4 ton model lifts with less strain and leaves margin for a crew cab with a loaded bed.
What size jack do I need for a Ram 2500 or 3500 diesel?
The front of a diesel heavy-duty Ram is heavy, so many owners choose a 4 or 5 ton jack for it. Check the jack’s maximum height too, because 4×4 heavy-duty trucks sit high at the axle.
Where should I put the jack on a Ram truck?
Use the jacking and lift points shown in the owner’s manual for your model year. They are usually at the axle or a frame or suspension point, never at step bars, running boards or the front air dam.
Can I keep using the jack that came with my Ram?
The factory jack is made for changing a flat at the roadside. For garage work a floor jack is steadier and easier to place, and in both cases the truck should sit on jack stands before you reach under it.
Prefer to hand the heavy lifting to someone else? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a pickup truck appointment on our contact page.
Working late? Park the Ram at 456 Carrier St NE in Grand Rapids, leave the keys in the after-hours drop-off, and the truck will be waiting for us in the morning.
