456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Half-Ton to Lifted: How to Pick the Best Jack Stands for Trucks

best jack stands for trucks: background of wall full of many similar aged shabby vintage wooden drawers with metal round handles

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

Stands that feel solid under a compact car can look short once a full-size pickup sits on them, and plenty of trucks get worked on in a driveway rather than a shop. The best jack stands for trucks reach your frame or axle at a comfortable working height and hold the load with a wide margin.

This guide covers how to size stands for a pickup, six pairs that span stock half-tons to lifted rigs, and how to set them safely. If you work on a mix of vehicles, our guide to jack stands for a home garage covers the general 3 ton range as well.

Quick answer

What size jack stands does a pickup truck need?

Most pickups are well served by a pair of 6 ton stands, chosen as much for the taller column as for the rating. The Big RED T46002A suits stock half-tons, the Hein-Werner HW93506 reaches 25-3/4 inches for leveled trucks, and the Big RED 12 Ton tops out near 28 inches for lifted ones.

Our Quick Picks

Three pairs for the most common pickup situations: a stock half-ton, a leveled or heavier truck and a lifted rig.

BIG RED T46002A product photo
Stock half-tons

BIG RED T46002A

6 ton pair, 15-3/8 to 23-13/16 in.

A double locking ratchet pair sized for everyday pickup work.

SuitsStock half-ton pickups
View on Amazon →
Hein-Werner HW93506 product photo
Tallest 6 ton

Hein-Werner HW93506

6 ton pair, 16-1/4 to 25-3/4 in.

Extra reach for leveled and heavier pickups without moving to a tall pin stand.

SuitsThree-quarter-ton and leveled trucks
View on Amazon →
Big RED 12 Ton product photo
Lifted trucks

Big RED 12 Ton

12 ton pair, 18-5/16 to 28-1/8 in.

A tall ratchet pair that reaches lifted frames with height to spare.

SuitsLifted pickups on larger tires
View on Amazon →

Measure First: Height Decides Most Truck Jobs

A stand has two numbers that matter on a pickup: the lowest and highest settings of its column. If the lowest setting is taller than the gap under your lift point, the stand will not fit. If the highest setting leaves the tire on the ground, the stand is useless for wheel and brake work.

Park on a level slab and take these measurements before you shop:

  1. Resting height: the floor to the frame rail, axle tube or support point your owner’s manual names, with the truck sitting on its tires.
  2. Raised height: the same spot once the tire is a couple of inches off the floor.

The raised height should fall in the middle of the stand’s range, not at the very top. A stand with a few inches of reach left over is the steadier choice.

Ratchet Bars, Pins and What “6 Ton” Really Means

Jack stand ratings almost always describe the pair, so a 6 ton pair is meant to share 12,000 lb between two stands. Since you only lift one end of a pickup at a time, a 6 ton pair has room to spare under most half-ton and three-quarter-ton trucks. Many truck owners pick 6 ton stands mainly because the column is taller and the base is wider than on a 3 ton model.

There are two common locking styles. Ratchet stands use a toothed bar and a pawl, so you can pull the column up a notch at a time and lock it quickly. Pin stands use a steel pin through a hole in the column, which is slower to set but gives a positive lock that cannot slip off a tooth.

Whichever style you choose, look for a stand that states compliance with the ASME PASE standard for portable automotive service equipment. Stands are one piece of a home toolkit, and our starter list of car maintenance tools for beginners shows what else belongs next to them.

Best Jack Stands for Trucks: Six Pairs in Detail

Capacities and height ranges below come from each Amazon listing. Check them against the numbers you measured on your own truck, and confirm the listing before you order.

1. Hein-Werner HW93506: 6 Ton Ratchet Jack Stands, 16-1/4 to 25-3/4 in.

Hein-Werner HW93506 product photo
Key features
  • 6 ton capacity, set of 2
  • Lifting range 16-1/4 to 25-3/4 in.
  • Formed steel frame, 10-1/2 x 13 in. base
  • Handle doubles as carry grip and column release

Hein-Werner’s HW93506 pair is a 6 ton ratchet stand with more top-end reach than most stands in its class. The listing gives a lifting range of 16-1/4 to 25-3/4 inches, roughly two inches higher at full extension than many 6 ton designs. On a leveled half-ton or a three-quarter-ton truck, that extra height can mean the column sits in the middle of its travel instead of near the top.

The frame is formed steel rather than a simple stamped tube, and the base measures 10-1/2 by 13 inches. A wide footprint helps on a pickup, where the load is high and any lean is easy to notice. The column adjusts on a multi-position ratchet bar, and one handle does two jobs: it is the carry grip and it is also the release for lowering the saddle column.

The minimum height of 16-1/4 inches is tall, so this pair will not slip under a lowered car or a truck on small tires. The listing does not mention a secondary locking pin, so compare it with a double-locking design if you want a backup lock. For a taller truck that a typical 6 ton stand only just reaches, it is a sensible step before a 12 ton pair.

View Hein-Werner HW93506 on Amazon

2. BIG RED T46002A: 6 Ton Double Locking Jack Stands, 15-3/8 to 23-13/16 in.

BIG RED T46002A product photo
Key features
  • 6 ton (12,000 lb) capacity, 1 pair
  • Lifting range 15-3/8 to 23-13/16 in.
  • Removable locking support pin
  • Pyramid base, 10.6 x 9.3 in.

The BIG RED T46002A from Torin is a pair of 6 ton ratchet stands with a lifting range of 15-3/8 to 23-13/16 inches. That span covers the frame rails and axle tubes on a large share of stock half-ton pickups, with some reach left over for lifting a tire clear. The 12,000 lb rating is shared across the pair, which leaves a generous margin when you raise one end of a light-duty truck.

Height is set with a forged iron ratchet bar that uses a sawtooth profile, so you can pull the column up and it drops into the next notch. A removable pin then passes through the column as a second lock, the double locking feature in the product name. The steel frame is welded, the saddle has a large contact area, and the pyramid foot base measures 10.6 by 9.3 inches.

The listing includes a limited 1-year manufacturer warranty. This pair is a general 6 ton stand, not a specialist one, so a heavily lifted truck may run out of height near the top of its travel. For a stock pickup that gets tire rotations, brake checks and fluid changes in the driveway, it is a straightforward and widely sold choice.

View BIG RED T46002A on Amazon

idyllic dirt road through lush forest

3. ARCAN ALJS6: 6 Ton Ratcheting Jack Stands, 15.5 to 24 in.

ARCAN ALJS6 product photo
Key features
  • 6 ton (12,000 lb) capacity across the pair
  • Height range 15.5 to 24 in.
  • Counter-weighted pawl lock
  • Contoured saddle with locating lugs

ARCAN’s ALJS6 is a 6 ton pair of ratcheting stands with a listed height range of 15.5 to 24 inches. On paper it sits close to other 6 ton ratchet stands, with a slightly higher top setting than some, which gives a stock or mildly leveled pickup a little more room at full height. The 12,000 lb rating covers the pair, so each stand shares the load from one end of the truck.

The detail that sets it apart is the saddle. ARCAN uses a large contoured saddle with locating lugs, designed to help a frame rail or axle sit centered instead of drifting toward an edge. The column locks with a counter-weighted pawl that drops into place as you raise it, then holds the setting until you deliberately release it. Construction is steel throughout.

ARCAN backs the pair with a 1 year warranty, according to the listing. There is no mention of a secondary locking pin, so readers who want two locks may lean toward a double-locking design instead. For owners who work under a half-ton pickup a few times a season and want a stand that positions the load clearly, this pair fits the job well.

View ARCAN ALJS6 on Amazon

4. GEARWRENCH GWJS6T: 6 Ton Ratcheting Jack Stands with Double Lock Pin

GEARWRENCH GWJS6T product photo
Key features
  • 6 ton rating, pack of 2
  • Double lock pin design
  • Ductile iron ratcheting bar
  • Meets ASME PASE-2019 requirements

GEARWRENCH is widely known for hand tools, and the GWJS6T is its 6 ton pair of ratcheting jack stands. The listing states that the stands meet the ASME PASE-2019 safety and performance requirements, which is the standard written for portable automotive service equipment such as jacks and stands. If you want a pair that names the edition of the standard it meets, this one does.

Height is adjusted with a ductile iron ratcheting bar, and a double lock pin passes through the column as a second layer of protection once the pawl has engaged. The feet are large and welded, which spreads the load over more floor area, and the saddle is wide to give the frame or axle more grip. Those are the right priorities for a truck, where the load sits high above the base.

The product data we checked does not give a height range, so confirm the minimum and maximum settings on the Amazon listing before you order, and compare them with your truck’s measurements. As a 6 ton ratchet stand, it should suit routine work on stock pickups, but lifted trucks may need a taller design. Check the fit first, then buy.

View GEARWRENCH GWJS6T on Amazon

vintage storage cabinet with labeled drawers in a dimly lit room

5. Big RED 12 Ton: Ratchet Jack Stands with Lock, 18-5/16 to 28-1/8 in.

Big RED 12 Ton product photo
Key features
  • 12 ton (24,000 lb) capacity, 2 pack
  • Height range 18-5/16 to 28-1/8 in.
  • Sawtooth multi-position ratchet bar
  • Tested to meet ASME standards

This Big RED pair moves up to a 12 ton rating, listed as 24,000 lb, with a height range of 18-5/16 to 28-1/8 inches. For a pickup the extra capacity is mostly a safety margin. The real reason to choose it is the reach: a lifted truck on large tires often needs more than the 24 inches or so that a typical 6 ton stand provides.

The stands are built from forged steel with a welded frame and a wide pyramid foot base. Height is set with a multi-position ratchet bar in a sawtooth pattern, so the column clicks up and locks at each notch. The saddle is large for better contact with a frame rail or axle tube, and the listing says the design was tested to meet ASME standards.

The tradeoff is the starting height. At just over 18 inches at its lowest, this pair will not fit under a stock half-ton at many support points, let alone a car. It is the pair to look at when your lifted truck runs a 6 ton stand near the top of its range, and you want the column sitting lower in its travel instead.

View Big RED 12 Ton on Amazon

6. Sunex 1410: 10 Ton High Height Pin Type Jack Stands, 28.1 to 46.5 in.

Sunex 1410 product photo
Key features
  • 10 ton (20,000 lb) across the pair
  • High height range 28.1 to 46.5 in.
  • 10 pin positions in 2 in. steps
  • 15.7 in. square base

The Sunex 1410 is a different kind of stand from the rest of this list. It is a high height, pin type pair rated at 10 tons across the two stands, with a listed range of 28.1 to 46.5 inches. A steel pin passes through one of ten holes in the column, set at 2 inch intervals, so each setting is a positive mechanical lock rather than a tooth and pawl.

The base is a 15.7 inch square, wider than the ratchet stands here, which helps when the support point sits that far above the floor. The saddle measures 3.1 by 5.1 inches and is shaped to center a frame rail or axle. Sunex lists the stands for supporting lifted vehicles during inspection, maintenance and repair, and backs them with a 1 year warranty.

That starting height of 28.1 inches is the key fact. Most stock and mildly lifted pickups sit well below it, so this pair suits tall suspension lifts, trucks raised on a hoist or jack for frame work, and heavy equipment. Measure your support point first; if it falls under 28 inches, a 6 or 12 ton ratchet stand is the right tool.

View Sunex 1410 on Amazon

Matching Stands to Your Pickup

Use the table to narrow the list, then let your own measurements settle the choice.

Truck setupHeight range to look forPairs from this list
Stock half-ton pickupAbout 15 to 24 in.Big RED T46002A, ARCAN ALJS6, GEARWRENCH GWJS6T
Three-quarter-ton or leveled truckUp to about 26 in.Hein-Werner HW93506, ARCAN ALJS6
Lifted truck on larger tiresAround 18 to 28 in.Big RED 12 Ton
Tall lifts or equipment support28 in. and upSunex 1410 High Height
Choosing the best jack stands for trucks by suspension height
moody highway through the forest

Setting Stands Under a Truck on a West Michigan Driveway

The jack raises the truck and the stands hold it, never the other way round. The OSHA rule on jacks sets the same order for workplaces: use equipment rated for the load, block the base on soft footing and secure the load once it is raised. Lower the truck onto a matched pair at the support points your manual shows, then give it a firm push before you reach underneath.

  • Chock first: block the wheels that stay down, set the parking brake and leave the transmission in park.
  • Inspect the support point: winters of road salt can leave frame rails flaking, so scrape away loose scale and look for solid metal before the saddle goes on.
  • Spread the load: on gravel, or on asphalt that softens in a humid July, set each stand on a thick plank or steel plate.
top view of a colorful and organized workshop drawer filled with tools and electronic components

Check your stands each spring and fall for bent legs, cracked welds or a pawl that no longer snaps into the teeth, and retire any stand that shows damage. When the wheels come back on, finish the lug nuts by hand with a calibrated wrench; our guide to the torque wrench choices for lug nuts explains why.

Jobs Better Left to a Lift

A good pair of stands makes tire rotations, brake inspections and fluid changes practical in your own driveway. Coil springs, ball joints and steering linkage on a full-size pickup are another matter, since they hold real force. Our suspension and steering repair service in Grand Rapids takes care of that kind of job.

beautiful winding road amidst dense pine trees and greenery on a sunny day

If you would rather hand over the maker’s service schedule too, our factory scheduled maintenance in Grand Rapids follows the intervals in your truck’s manual.

Frequently Asked Questions

Are 3 ton jack stands enough for a pickup?

On a light half-ton, a 3 ton pair can carry the weight of one end, but many of those stands top out too low to lift the tire clear. A 6 ton pair usually gives a taller column and a wider base, which is why truck owners tend to prefer it.

What are the best jack stands for trucks with a lift kit?

Look for a range that reaches your raised frame with a few inches left over. The Big RED 12 Ton pair goes to about 28 inches, and the Sunex 1410 High Height pair starts at 28.1 inches for very tall setups.

Can jack stands go under the axle of a truck?

On many solid-axle pickups the axle tube is a common support point, but the owner’s manual has the final say. Keep the saddle away from brake lines, the differential cover and shock mounts, and center the tube in the saddle.

Is a pin style or ratchet stand better for a truck?

Both work when they are rated for the load and set correctly. Ratchet stands adjust faster for routine jobs, while pin stands give a positive lock that many owners like for long projects under a heavy truck.

Want your pickup up on a lift for suspension, brake or scheduled service work instead? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or send us a request on the contact page.

Working late? Park the truck at 456 Carrier St NE in Grand Rapids and use the after-hours drop-off, and we will pick it up from there.