456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Scraping the Front Lip? Best Car Ramps for Low Cars

best car ramps for low cars: view from inside a garage showing open roller shutter

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A front lip that scrapes before the tire even touches the ramp is the classic low-car problem. The best car ramps for low cars solve it with a gentle incline, a long enough run and, in some cases, a ramp nose that comes off once the car is up.

This guide covers how to check your own clearance, which type of ramp fits the job you have in mind, and five sets built for cars that sit close to the pavement. For ramps in general, including taller pairs for SUVs and trucks, see our full guide to car ramps.

Quick answer

Which ramps work on a lowered or low-nose car?

Look for an incline near 9 to 11 degrees. For working underneath, a long service ramp such as the Race Ramps foam pair or the MaxxHaul 50709 gives 6 to 8 inches of lift. If you only need room for a floor jack, a 2.5 inch ramp like the Black Widow or Tomioka TR-SLOPE does that job.

Our Quick Picks

Three sets that cover the usual low-car jobs: a long foam service ramp, a detachable plastic pair and a short ramp for jack clearance.

Race Ramps 56 in. Foam Ramps product photo
Long, gentle climb

Race Ramps 56 in. Foam Ramps

8 in. lift · 10.8 degrees

Light foam ramps with a long run that suits cars with low front lips.

SuitsLighter sports cars and compacts
View on Amazon →
MaxxHaul 50709 product photo
Detachable pick

MaxxHaul 50709

6.5 in. lift · 9.5 degrees

A plastic service ramp whose entry section unclips to clear space under the car.

SuitsHeavier low cars that need room to work
View on Amazon →
Black Widow Low Car Ramps product photo
Jack clearance

Black Widow Low Car Ramps

2.5 in. lift · 9.05 degrees

Short honeycomb ramps that raise a low car just enough for a floor jack.

SuitsCars too low for a jack to slide under
View on Amazon →

Will Your Front Lip Clear? Measuring Before You Buy

Ramp listings give an angle in degrees, which is hard to picture. Converted to rise per foot, a 9 degree ramp climbs about 1.9 inches for every 12 inches of length, a 9.5 degree ramp about 2 inches and a 10.8 degree ramp about 2.3 inches. Your bumper has to stay above that surface for the whole climb.

Two measurements tell you most of what you need. First, park on a level floor and measure from the ground to the lowest point of the front lip, splitter or air dam. Second, measure how far that point sits ahead of the front tire’s contact patch.

Then do the dry run. Set one ramp against the front of the tire and look at the gap between the lip and the ramp surface directly under it. If there is less than an inch of daylight, that ramp is too steep or too tall at that point for your car, and the bumper will likely catch as the suspension compresses on the way up.

Cars with a long front overhang are harder than the angle alone suggests, because the lip reaches the taller part of the ramp before the tire does. That is where a longer, gentler ramp or a short starter ramp in front of the main one earns its keep.

Service Ramps or Jack-Access Ramps?

Low-car ramps fall into two groups that do different jobs. Service ramps lift the car 6 inches or more and are meant to hold it while you drain oil or inspect the exhaust. Jack-access ramps add only about 2.5 inches, which is not enough room to work under the car, but it is enough to roll a floor jack under a car that otherwise sits too low for one.

Many owners end up with both. They drive onto the short ramps, slide the jack in at the factory lift point, raise the car and set jack stands, then do the work with the car on stands. Our guide to low profile floor jacks covers the jack half of that routine, and our starter list of car maintenance tools rounds out a first garage kit.

Best Car Ramps for Low Cars: Five Sets Up Close

Two of these sets are service ramps and three are low jack-access ramps. All figures come from the Amazon listings or the maker’s page, so check your car’s weight and clearance against them before ordering.

1. Race Ramps 56-Inch Foam Service Ramps: 8 in. Lift on a 10.8 Degree Approach

Race Ramps 56 in. Foam Ramps product photo
Key features
  • 10.8 degree approach (listing)
  • 8 in. lift per the title
  • 1,500 lb per ramp
  • About 10 lb each, carry straps

Race Ramps makes this pair from high-density polystyrene foam with a polyurea coating, shaped as one long 56 inch piece per side. The length is the point for a low car: the climb is spread over a long run, so the front lip has more room before the ramp reaches full height. The listing gives the approach as 10.8 degrees in the title and 10.75 degrees in the bullets.

The title lists an 8 inch lift, while one bullet mentions 10 inches, so confirm the height on the listing before you order. Each ramp is rated for 1,500 lb, which works out to about 3,000 lb across a front axle. That suits many light coupes, roadsters and compact hatchbacks, but a heavier sedan or a car with a nose-heavy engine layout may be past it.

Each ramp weighs about 10 lb and comes with a carrying strap, and the foam does not scratch or mark a painted or epoxy floor, which is why these are also used at car shows. The trade-off is a lower load rating than most plastic ramps. If your car is light and your lip is low, this pair is a sensible starting point, backed by a 1-year maker warranty.

View Race Ramps 56 in. Foam Ramps on Amazon

2. MaxxHaul 50709 Detachable Car Ramps: 6.5 in. Lift, 6,500 lb Pair with 9.5 Degree Incline

MaxxHaul 50709 product photo
Key features
  • 9.5 degree incline
  • 6-1/2 in. lift
  • 3,250 lb per ramp, 6,500 lb pair
  • Detachable, extendable front section

The MaxxHaul 50709 is a two-part polypropylene ramp: a front entry section and a runner that the tire sits on. Tabs on the runner lock into notches on the entry piece, and once the car is up you can pull the front section away to open more room for a creeper or a drain pan. MaxxHaul lists the incline at 9.5 degrees and the lift at 6-1/2 inches.

The listing rates each ramp at 3,250 lb and the matched pair at 6,500 lb, with a 15 inch maximum tire width and overall dimensions of 52-1/2 by 15 by 8-1/2 inches. The pair weighs about 33 lb and has molded side handles. For cars that still catch, MaxxHaul sells middle extension sections separately, which lengthen the run, as its 50709 product page describes.

MaxxHaul says to use the ramps only as a matched pair, and only on a hard, level surface, never on gravel, grass or a slope. This is the set to consider when a car is too heavy for foam but still needs a shallow approach. It is less suited to very wide performance tires beyond the 15 inch limit.

View MaxxHaul 50709 on Amazon

aerial shot of sprawling highway interchange in Los Angeles with sparse traffic

3. Black Widow Low Car Ramps: 2.5 in. Lift, 5,000 lb per Axle with 9.05 Degree Angle

Black Widow Low Car Ramps product photo
Key features
  • 2.5 in. lift
  • 9.05 degree loading angle
  • 5,000 lb per axle, 10,000 lb GVW
  • Honeycomb plastic with tire stop

These Black Widow ramps, sold under the Rage Powersports name, are short plastic blocks with a shallow slope rather than full service ramps. They raise the tires 2.5 inches on a 9.05 degree loading angle, which is often enough to get a floor jack saddle under a car that otherwise sits too low for one. Each ramp measures 27.5 by 7.75 by 2.5 inches.

The listing rates the pair at 5,000 lb per axle and 10,000 lb gross vehicle weight, so most passenger cars fall well within it. The honeycomb body keeps weight down and lets moisture drain rather than pool under the tire. A slight stop at the far end tells the driver the tire has reached the top, and Black Widow advises using a spotter to avoid rolling off.

Black Widow mentions oil filter access, but 2.5 inches is a small gain for working under a car. Their real value is the first step of a jack-and-stands routine on a lowered car, where a car that sits an inch or two too low for the jack is a common snag. They are not a substitute for taller service ramps if you plan to spend time underneath.

View Black Widow Low Car Ramps on Amazon

4. Tomioka Racing TR-SLOPE Low Profile Ramps: 2.56 in. Lift, 6,600 lb Pair

Tomioka Racing TR-SLOPE product photo
Key features
  • 2.56 in. lift
  • 9.05 degree approach
  • 6,600 lb pair, 3,300 lb per ramp
  • Recycled plastic, nests for storage

The Tomioka Racing TR-SLOPE is a pair of short, hard ramps made from recycled plastic. They exist for one simple purpose: adding a little height under the tires of a lowered car so a floor jack can reach the lift points. The listing gives a 2.56 inch lift and a 9.05 degree approach, which keeps most front lips clear on the way up.

Capacity is listed at 3,300 lb per ramp and 6,600 lb for the pair. The top surface uses a honeycomb pattern with channels that let water drain, which helps in a garage where melting snow drips off the car. Each ramp is roughly 27-1/2 inches long, 7-3/4 inches wide and 2-1/2 inches high, and the two nest together so they take up little shelf space.

Tomioka says to check vehicle and jack clearance before use and to follow its instructions on positioning. As with any ramp this short, plan on lifting the car with a jack and setting stands for real work underneath. The narrow 7-3/4 inch width can be tight for very wide tires, so compare it with your tread width first.

View Tomioka Racing TR-SLOPE on Amazon

spacious industrial workshop featuring advanced machinery and organized workstations

5. Megan Racing Low Profile Drive-On Ramps: 2.56 in. Raise, Detachable into Four Pieces

Megan Racing Detachable Ramps product photo
Key features
  • Raises 2.56 in.
  • Splits into 4 pieces
  • 5,000 lb GVW each side
  • 27.8 x 7.8 x 3.5 in. per ramp

Megan Racing sells this pair as low profile drive-on ramps for cars that need help getting a jack underneath. Each ramp is made from a high-strength plastic composite and comes apart into two pieces, so the set separates into four sections in total for storage or setup. The listing gives a raise of 2.56 inches and overall dimensions of 27.8 by 7.8 by 3.5 inches per ramp.

The split design is the useful part. After the tire is on the raised section, removing the entry piece leaves open floor in front of the wheel, which gives a floor jack more room to roll in and reach a front lift point. That matters on cars where even a low-profile jack struggles to fit between the lip and the floor.

The listing rates the ramps at 5,000 lb gross vehicle weight on each side, which covers most passenger cars. It does not give an approach angle, so the dry-run lip check is worth doing before you drive on. Like the other short ramps here, this set is for jack access, not for holding the car while you work under it.

View Megan Racing Detachable Ramps on Amazon

Side-by-Side: Lift, Angle and Rating

When you shortlist the best car ramps for low cars, the listed numbers make the split between the two groups easy to see. Ratings are given in different ways by each maker, so compare per-ramp or per-axle figures against your car’s front axle weight, which is on the door jamb sticker or in the owner’s manual.

Ramp setListed liftListed angleListed rating
Race Ramps 56 in. foam8 in. (title)10.8 degrees1,500 lb per ramp
MaxxHaul 507096.5 in.9.5 degrees6,500 lb per pair
Black Widow low car ramps2.5 in.9.05 degrees5,000 lb per axle
Tomioka Racing TR-SLOPE2.56 in.9.05 degrees6,600 lb per pair
Megan Racing detachable2.56 in.Not listed5,000 lb GVW each side
Low-car ramp sets compared by listed lift, incline and capacity
vibrant aerial view of a cityscape featuring a highway

The foam pair has the lowest per-ramp rating here, so it is aimed at lighter sports cars and compacts. The MaxxHaul is the one to look at for a heavier sedan or coupe that still needs a shallow approach.

Getting a Low Car Up the Ramps in a Michigan Garage

A careful setup matters more on a low car, because there is little room for error and the lip is easy to crack. These steps cover the basics:

  1. Dry the tires and floor: winter slush carries road salt and water into the garage, and wet plastic or foam loses grip under a turning tire.
  2. Square the ramps: line both up straight with the front tires so the car climbs evenly and does not twist.
  3. Use a spotter: a second person watching the lip and the ramp ends is the easiest way to avoid a roll-off.
  4. Creep, do not rev: steady, slow throttle keeps the ramps from shooting forward on a smooth floor.
  5. Lock it in place: set the parking brake, put it in park or gear, and chock the rear wheels before you go under.
three blue garage doors in a brick building on a sunny day

If the ramps slide on a sealed or epoxy floor, a rubber mat under each one or a fixed stop in front of the ramp ends usually helps. Doing an oil change without crawling under at all is another option, and our fluid extractor buying guide explains when a topside extraction works.

When the Job Needs a Lift Instead

Ramps keep the wheels loaded, which is fine for an oil drain but no help for brakes, wheel bearings or anything that needs a wheel off. Lowered cars also hide problems ramps cannot show, such as a scraped exhaust or worn suspension parts that only show up with the suspension hanging.

tranquil desert scene featuring a winding road under a clear blue sky

When you would rather skip the crawling, our oil change service in Creston handles the routine drain and fill. For a full check against your maker’s schedule, book factory scheduled maintenance in Grand Rapids, and if the exhaust has taken a few hits from speed bumps, see our exhaust repair page.

Frequently Asked Questions

What approach angle do I need for a lowered car?

Most low-car ramps list angles between about 9 and 11 degrees. The angle alone does not settle it, because a long front overhang meets the taller part of the ramp first. Measure your lip height and do a dry run with one ramp before you drive up.

Can I change my oil on 2.5 inch ramps?

Those ramps are mainly for getting a floor jack under the car. Use them to gain jack clearance, lift the car at its factory points and support it on jack stands before you go underneath.

Are foam ramps strong enough for a car?

Race Ramps rates its 56 inch foam pair at 1,500 lb per ramp, which suits many light sports cars and compacts. Check your front axle weight on the door jamb sticker, and choose a higher-rated plastic pair if your car is heavier.

Do I need wheel chocks with car ramps?

Yes. Chock the wheels still on the ground, set the parking brake and leave the car in park or in gear. Plastic and foam ramps can also shift on a smooth floor, so check that they sit square before you slide under.

Low car due for service and short on clearance at home? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a visit through our contact page.

If daytime hours do not work for you, the after-hours drop-off is an option. Bring the car to 456 Carrier St NE, Grand Rapids 49505, whenever it suits your evening.