As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Few repairs on a Silverado or Equinox start as often with a scan tool as an oxygen sensor job. The best O2 sensor for Chevy owners is not one magic brand but a single genuine part made for the exact model, engine, years and position named in the trouble code.
Below you will find how GM numbers its sensors, then six DENSO and NTK listings for Silverado trucks, the Equinox and the Malibu. For the wider maker picture, our roundup of oxygen sensor brands compares the big names side by side.
Quick answer
Which O2 sensor should you buy for a Chevy?
Buy a genuine OE-supplier sensor, such as DENSO or NTK, whose listing names your Chevy model, engine, years and position. A 2010 Silverado 5.3L needs a different downstream part than a 2016 truck, and V8 codes point to bank 1 or bank 2. Read the code first, then replace only that sensor.
Our Quick Picks
Three quick picks: an upstream sensor for the 2006-2013 Silverado, a downstream sensor for the 2014-2018 truck and an upstream sensor for the 2.4L Equinox. All six are reviewed below.

DENSO Upstream (Silverado 2006-13)
A genuine DENSO sensor listed for the GMT900-era Silverado 1500.

NTK Downstream Left (Silverado 2014-18)
A genuine NTK sensor for the newer-body Silverado 1500.

DENSO Upstream (Equinox 2.4L)
A genuine DENSO front sensor for the four-cylinder Equinox.
How GM Numbers Its Oxygen Sensors
Every Chevy sold in the US since the OBD-II era has at least two oxygen sensors. Sensor 1, the upstream unit, sits ahead of the catalytic converter and reports whether the engine runs rich or lean. Sensor 2, the downstream unit, sits behind the converter and mostly checks that the converter still stores and releases oxygen.
- Four-cylinder cars and crossovers: the 2.4L Equinox and Malibu have one cylinder bank, so you only choose upstream or downstream.
- V6 and V8 trucks: the 4.3L, 4.8L, 5.3L, 6.0L and 6.2L engines have two banks, each with its own sensor 1 and sensor 2.
- Bank 1 on a Chevy V8: cylinder 1 sits on the driver side of GM’s V8 engines, so bank 1 is the driver side and bank 2 is the passenger side.
The code tells you which one to pull. P0135 is the heater circuit for bank 1, sensor 1, P0141 is bank 1, sensor 2, and P0155 moves the same heater fault to bank 2, sensor 1.
What a Good Chevy Sensor Listing Tells You
We left out the cheap four-packs that claim to fit two decades of GM trucks at once. Each pick below is one genuine DENSO or NTK sensor, sold as a single part, with one model, one span of years and one named position in its title.
Those details matter on Chevy trucks because GM changed sensors between body styles. A 2008-2013 Silverado and a 2014-2018 Silverado share engine sizes but not every downstream part, and the 2500 HD runs its own listings. Run your VIN through the Amazon fit checker before checkout, since no single listing covers every Chevy.
Best O2 Sensor for Chevy: Six Listings by Truck and Car
The first four sensors suit Silverado pickups across three generations, and the last two suit the 2.4L Equinox and Malibu. Each is a direct-fit part with a factory-style plug, so no splicing is needed.
1. DENSO Upstream O2 Sensor: Direct Fit for 2006-13 Silverado 1500 4.3L, 4.8L and 5.3L

- Listed for 2006-2013 Silverado 1500
- Covers the 4.3L V6, 4.8L V8 and 5.3L V8
- Upstream position, ahead of the converter
- Genuine DENSO part with hardware included
This DENSO sensor is listed for the 2006 to 2013 Chevrolet Silverado 1500 with the 4.3L V6, the 4.8L V8 or the 5.3L V8, in the upstream position. Upstream means it threads into the exhaust ahead of the catalytic converter, where the engine computer reads it to judge the air-fuel mixture. On the V8 trucks each bank carries its own upstream sensor, so your code tells you which side needs one.
The listing calls it a genuine DENSO part, shipped in original packaging with its hardware and sold as a direct replacement. That means a factory-style plug that clicks into the existing harness, with no cutting or crimping under a truck that sees slush and road salt every winter. DENSO is a long-standing original-equipment supplier, and a single sensor with a named position is easier to match than a mixed multi-pack.
Pick this one when a scan tool reports a bank 1 or bank 2, sensor 1 fault on a 2006-2013 Silverado 1500, or when tired originals on a high-mileage 5.3L are slowing fuel trims. Run the VIN through the Amazon fit checker before ordering, because the Classic body style and the 2014-on trucks use different parts. It is not the right part for a downstream position or a heavy-duty 2500 or 3500.
View DENSO Upstream (Silverado 2006-13) on Amazon
2. DENSO Downstream O2 Sensor: Direct Fit for 2008-13 Silverado 1500 V8

- Listed for 2008-2013 Silverado 1500
- Covers the 4.8L, 5.3L, 6.0L and 6.2L V8
- Downstream position, behind the converter
- Genuine DENSO part with hardware included
This DENSO sensor is listed for the 2008 to 2013 Chevrolet Silverado 1500 with the 4.8L, 5.3L, 6.0L or 6.2L V8, in the downstream position. It sits behind the catalytic converter, and its main job is to confirm that the converter is still storing and releasing oxygen as it should. Its signal changes far more slowly than an upstream sensor’s, which is exactly what the engine computer expects to see.
According to the listing, it is a genuine DENSO part in original packaging, with hardware included, made as a direct replacement for the factory sensor. The plug matches the truck’s harness, so there is no splicing near the transmission crossmember where the wiring runs. Because the 6.0L and 6.2L share this listing with the more common 4.8L and 5.3L, one part covers most V8 trucks from these years.
Choose it when a code calls out sensor 2, such as a slow-response or heater fault behind the converter on a 2008-2013 V8 Silverado. Check the year, engine and position on Amazon before you buy, since the 4.3L V6 and the earlier trucks are listed separately. It will not cure a worn converter, and it is not meant for any upstream position.
View DENSO Downstream (Silverado 2008-13) on Amazon

3. NTK Downstream Left O2 Sensor: Direct Fit for 2014-18 Silverado 1500

- Listed for 2014-2018 Silverado 1500
- Covers the 4.3L V6, 5.3L V8 and 6.2L V8
- Downstream left position, behind the converter
- Genuine NTK part with hardware included
This NTK sensor is listed for the 2014 to 2018 Chevrolet Silverado 1500 with the 4.3L V6, the 5.3L V8 or the 6.2L V8, in the downstream left position. On these trucks each bank feeds its own converter and its own rear sensor, so the listing names a side as well as a position. In US parts listings left means the driver side, which on a GM V8 is also bank 1.
NTK is the sensor brand sold alongside NGK spark plugs, and the listing describes this as a genuine NTK part in original packaging with its hardware. It is built as a direct replacement, with a factory-style connector that plugs into the existing harness. That matters on the newer trucks, where the rear sensor plugs sit up high and a splice would be hard to seal against water and salt.
Reach for it when a code or live data points to the left downstream sensor on a 2014-2018 Silverado 1500, which commonly shows up as a bank 1, sensor 2 fault. Use the Amazon fit checker with your VIN before ordering, since the right-side sensor is a separate part. It does not suit the upstream positions or the earlier 2008-2013 trucks.
View NTK Downstream Left (Silverado 2014-18) on Amazon
4. DENSO Upstream O2 Sensor: Direct Fit for 2011-15 Silverado 2500 HD 6.0L V8

- Listed for 2011-2015 Silverado 2500 HD
- Made for the 6.0L gas V8
- Upstream position, ahead of the converter
- Genuine DENSO part with hardware included
This DENSO sensor is listed for the 2011 to 2015 Chevrolet Silverado 2500 HD with the 6.0L gas V8, in the upstream position. Heavy-duty trucks have their own exhaust routing, so they often need a different sensor from a half-ton with a similar engine. A separate listing for the 2500 HD takes the guesswork out of that difference.
The listing describes a genuine DENSO part, packed in original packaging with the hardware included and built as a direct replacement. The factory-style plug clips straight into the harness, which helps on a work truck that spends its days on job sites, gravel and salted roads. Upstream sensors report the air-fuel mixture constantly, so a slow or failing one can hurt fuel trims, idle quality and towing response.
Pick it when a 6.0L 2500 HD from these years shows a sensor 1 fault on either bank, or when the originals are slow after high mileage and heavy towing. Confirm the year, model and engine on Amazon first, because the Duramax diesel trucks use different exhaust sensors. It is not meant for the downstream positions or for any Silverado 1500.
View DENSO Upstream (Silverado 2500 HD 6.0L) on Amazon

5. DENSO Upstream O2 Sensor: Direct Fit for 2015-17 Equinox 2.4L

- Listed for 2015-2017 Chevrolet Equinox
- Made for the 2.4L four-cylinder
- Upstream position, ahead of the converter
- Genuine DENSO part with hardware included
This DENSO sensor is listed for the 2015 to 2017 Chevrolet Equinox with the 2.4L four-cylinder, in the upstream position. The 2.4L has a single cylinder bank, so there is no left or right to sort out, only front or rear of the converter. That makes it one of the easier Chevy sensor jobs to match, provided the year range is right.
The listing calls it a genuine DENSO part in original packaging, with the hardware included, designed as a direct replacement for the factory sensor. The plug fits the existing connector without any cutting. The upstream sensor gives the engine computer its main feedback on the air-fuel mixture, so a sluggish one can show up as poor mileage, a rough idle or a failed readiness check.
Use it when a code points to bank 1, sensor 1 on a 2015-2017 Equinox 2.4L, such as a heater circuit or slow-response fault. Check fit by VIN on Amazon before ordering, because earlier Equinox years and the V6 models use other parts. It does not suit the downstream position, and it will not solve a lean code caused by a vacuum leak or a dirty mass airflow sensor.
View DENSO Upstream (Equinox 2.4L) on Amazon
6. DENSO Downstream O2 Sensor: Direct Fit for 2013-14 Malibu 2.4L

- Listed for 2013-2014 Chevrolet Malibu
- Made for the 2.4L four-cylinder
- Downstream position, behind the converter
- Genuine DENSO part with hardware included
This DENSO sensor is listed for the 2013 and 2014 Chevrolet Malibu with the 2.4L four-cylinder, in the downstream position. It threads in behind the catalytic converter and watches the exhaust leaving it, which is how the engine computer judges converter health. With one cylinder bank there is a single rear sensor to replace.
Per the listing, it is a genuine DENSO part in original packaging, supplied with its hardware and made as a direct replacement. A factory-style plug means it connects to the existing harness with no splicing under the car. Because the downstream signal feeds the converter efficiency test, a failed rear sensor can keep the check engine light on and stop the catalyst monitor from completing.
Choose it when a 2013-2014 Malibu 2.4L throws a bank 1, sensor 2 code, such as a heater circuit fault or a sensor that stays stuck at one voltage. Confirm the year and engine with the Amazon fit checker first, since the 2008-2012 Malibu and the turbo engines are listed separately. It is not an upstream part, and a new rear sensor will not revive a converter that has worn out.
View DENSO Downstream (Malibu 2.4L) on Amazon
Which Listing Fits Your Chevy
| Chevy | Engine and years | Position | Listing |
|---|---|---|---|
| Silverado 1500 | 4.3L, 4.8L, 5.3L, 2006-2013 | Upstream | DENSO |
| Silverado 1500 | 4.8L to 6.2L V8, 2008-2013 | Downstream | DENSO |
| Silverado 1500 | 4.3L, 5.3L, 6.2L, 2014-2018 | Downstream left | NTK |
| Silverado 2500 HD | 6.0L V8, 2011-2015 | Upstream | DENSO |
| Equinox | 2.4L, 2015-2017 | Upstream | DENSO |
| Malibu | 2.4L, 2013-2014 | Downstream | DENSO |
Driving something not in the table, such as a Tahoe, Colorado or Cruze? Look for a genuine-brand listing that names your engine and the position from your code. The best O2 sensor for Chevy trucks and cars is the one the fit checker confirms for your VIN details, not the pack with the longest vehicle list in its title.

Rusty Bungs and Winter Road Salt
A Chevy that has seen ten Grand Rapids winters usually has salt crust packed around every exhaust fitting. Soak the sensor threads with penetrating oil the evening before, then work it loose with the pipe warm, not scorching and not frozen. A slotted 22mm (7/8 in) socket clears the pigtail, and our O2 sensor socket comparison covers the offset and crowfoot tools for the tight spots behind a truck’s transmission.
DENSO and NTK sensors normally ship with anti-seize already applied, so keep extra compound away from the tip. Route the new lead along the original clips, well clear of the hot pipe.

Look over the rest of the exhaust while the truck is up. A cracked manifold, a broken stud or a leaking flange ahead of an upstream sensor lets outside air in, and a good sensor then reports a lean mixture that isn’t really there. A small hole further back can be sealed with an exhaust patch or clamp kit to hold you over until a proper repair.
When the Code Points Past the Sensor
A lazy or failed sensor brings rough idle, poor mileage and readiness monitors that won’t set, and our guide to symptoms of a bad oxygen sensor lists the rest. Still, P0171 and P0174 lean codes on a Vortec V8 often trace to a vacuum leak or a weak fuel supply, and P0420 or P0430 usually means a tired converter. Even the best O2 sensor for Chevy engines can’t fix those faults.

The nonprofit Car Care Council notes in its free Car Care Guide that a flashing check engine light means a problem is happening right now and needs attention at once. Our check engine light diagnostics in Grand Rapids use live sensor data to find the real cause. When the answer is a leak or a converter, we also handle exhaust repair in Grand Rapids.
More Buying Guides
Frequently Asked Questions
Which side is bank 1 on a Chevy V8?
Bank 1 is the side that holds cylinder 1, which on GM’s V8 engines is the driver side. Bank 2 is the passenger side. A code ending in sensor 1 means the upstream sensor on that bank, and sensor 2 means the one behind the converter.
Should I replace all four O2 sensors on my Silverado?
Usually not. Replace the one the code and live data point to. On a high-mileage truck some owners change both upstream sensors together so the banks react alike, but the downstream pair rarely needs replacing at the same time.
Is DENSO or NTK better than ACDelco for a Chevy?
All three are original-equipment suppliers, so the brand matters less than the fit. Pick the genuine sensor listed for your model, engine, years and position, and avoid unbranded multi-packs that claim to cover every GM truck.
Does a Silverado 2500 HD use the same sensor as a 1500?
Not always. Heavy-duty trucks have their own exhaust layout and often their own sensor listings, even with a similar V8. Shop by the exact model, such as the 2011-2015 2500 HD with the 6.0L, rather than by engine size alone.
Want the light diagnosed before you buy a sensor? Ring 456 AutoFix on 616-279-3832 any weekday from 8am to 5pm, or send us a booking request online.
If your workday matches our hours, bring the Chevy to 456 Carrier St NE after we close and use the after-hours drop-off. We will start on it when the shop opens.
