456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Accord, Civic or CR-V: Finding the Best O2 Sensor for Honda by Engine

best o2 sensor for honda: scenic view of a snowy mountain road surrounded by wintery landscapes and snow-covered trees

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Honda that throws an oxygen sensor code usually keeps running fine, which makes it tempting to grab whichever sensor is cheapest. The best O2 sensor for Honda models is the one built for your exact year, engine and position, because the front and rear sensors on most Hondas are two different kinds of part.

This guide sorts six genuine DENSO and NTK listings by model, covering the Accord, Civic and CR-V. If you are still choosing between sensor makers in general, our look at how to pick an oxygen sensor brand covers the wider field.

Quick answer

Which oxygen sensor should you put in a Honda?

Use a genuine DENSO or NTK sensor listed for your Honda’s year, engine and position. The upstream unit on most Hondas from the early 2000s on is an air-fuel ratio sensor, such as the DENSO 234-9040 for a 2003-2007 Accord, while the downstream unit is a conventional heated O2 sensor.

Our Quick Picks

Three quick picks: an older Accord upstream sensor, a later Civic upstream sensor and a CR-V downstream sensor. All six listings are reviewed below.

DENSO 234-9040 (Accord 2003-07) product photo
Accord 2003-07 pick

DENSO 234-9040 (Accord 2003-07)

Upstream A/F · 234-9040 · Accord

DENSO's own boxed air-fuel ratio sensor for the seventh-generation Accord.

Suits2003-2007 Accord owners with an upstream sensor fault
View on Amazon →
NTK Upstream AFR (Civic 2.0L 2016-20) product photo
Civic 2.0L pick

NTK Upstream AFR (Civic 2.0L 2016-20)

Upstream A/F · 2016-20 · 2.0L

Genuine NTK wideband sensor for the tenth-generation Civic with the 2.0L engine.

Suits2016-2020 Civic 2.0L owners chasing an upstream fault
View on Amazon →
DENSO Downstream O2 (CR-V 2.4L 2010-13) product photo
CR-V rear pick

DENSO Downstream O2 (CR-V 2.4L 2010-13)

Downstream O2 · 2010-13 · 2.4L

A genuine DENSO heated O2 sensor for the rear port on the third-generation CR-V.

Suits2010-2013 CR-V owners with a Sensor 2 fault
View on Amazon →

Air-Fuel Ratio Sensor or O2 Sensor: Honda’s Two Front-to-Back Parts

Most Hondas built since the early 2000s carry an air-fuel ratio sensor, often shortened to A/F sensor, ahead of the catalytic converter. This wideband part reports how rich or lean the mixture is across a broad range, and the engine computer trims fuel from that reading. Behind the converter sits a conventional narrowband heated oxygen sensor that mainly watches how well the converter is storing oxygen.

The two are not interchangeable. They use different connectors, wiring and signals, so a downstream sensor will not work in the upstream port, even though both thread into the same 22mm boss. Skip any Honda listing that does not name a position.

Honda four-cylinder engines have one cylinder bank, so the scan tool calls the upstream sensor Bank 1 Sensor 1 and the downstream one Bank 1 Sensor 2. V6 Hondas add a second bank, so the side matters too.

Checking a Honda Sensor Listing Before It Ships

Start with the model year range and the engine size, then the position. A 2.4L Accord and a 3.0L V6 Accord from the same year use different upstream sensors. The best O2 sensor for Honda shoppers is a listing that names all three details in the title, as the six below do.

Next, look at who made it. DENSO and NTK both supply sensors to carmakers, and both build direct-fit parts with the factory-style connector already attached. Universal sensors and two-packs claiming to fit a dozen models cost less, but a wrong signal or weak crimp can bring the light back.

Finally, run your car through Amazon’s Confirmed Fit tool with the exact trim. If your code reader already named the sensor position, you are ready to order; if not, our list of bad oxygen sensor symptoms helps you confirm the sensor is really the suspect.

Best O2 Sensor for Honda: Six Listings by Model

Every pick is a specific Amazon US listing that names its Honda model, years, engine and position. Four are upstream air-fuel ratio sensors and two are downstream O2 sensors, so match the position to your fault code first.

1. DENSO 234-9040 Air/Fuel Ratio Sensor: Wideband Upstream Part for 2003-07 Honda Accord

DENSO 234-9040 (Accord 2003-07) product photo
Key features
  • Listed for the 2003-2007 Honda Accord
  • Wideband air-fuel ratio sensor, upstream
  • Platinum electrodes, planar zirconia element
  • 4-wire, 16.14 in harness with connector

The DENSO 234-9040 is an air-fuel ratio sensor listed for the 2003 to 2007 Honda Accord, and it sits in the upstream position ahead of the catalytic converter. It is sold under DENSO’s own part number, and the listing gives Honda interchange numbers 36531RAAA01 and 36531RAAA02, which makes cross-checking against the part on your car straightforward.

The listing describes a wideband sensor with tarnish-proof platinum electrodes and a quick-response planar zirconia element. It measures air-fuel ratios from roughly 12:1 to 19:1, which lets the engine computer see exactly how far the mixture has drifted rather than just rich or lean. The four-wire harness is about 16 inches long and ends in a factory-style connector, so there is nothing to cut or splice under the car.

Use it when a scan tool points to Bank 1 Sensor 1 on a seventh-generation Accord, or when a high-mileage original sensor responds slowly in live data. Replacement listings for this part number point to the 2.4L four-cylinder, and the V6 uses a different sensor, so run your car through Amazon’s fit checker, since the title names only the model and years. It is not a downstream sensor and does not suit later Accords.

View DENSO 234-9040 (Accord 2003-07) on Amazon

2. DENSO Upstream Air-Fuel Ratio Sensor: Direct Fit for 2013-17 Honda Accord 2.4L

DENSO Upstream AFR (Accord 2.4L 2013-17) product photo
Key features
  • Listed for 2013-2017 Accord 2.4L four-cylinder
  • Upstream air-fuel ratio sensor position
  • Genuine DENSO part in original packaging
  • Direct replacement with hardware included

This DENSO air-fuel ratio sensor is listed for the 2013 to 2017 Honda Accord with the 2.4L four-cylinder, in the upstream position. That covers the ninth-generation Accord most drivers bought, and it is a separate part from the sensor used on the V6 cars of the same years, so the engine size in the title matters.

The seller lists it as a genuine DENSO part that arrives in its original packaging with the hardware included, sold as a direct replacement. That means the connector and harness length should match the factory part, which avoids splicing wires in a spot that sees heat, water and winter salt. The upstream sensor gives the engine computer its main mixture reading, so a lazy or failed one can upset fuel trims, idle quality and fuel economy.

Reach for it when a code or live data points to Bank 1 Sensor 1 on a four-cylinder ninth-generation Accord. Enter your exact trim in the Amazon fit checker, since hybrid and V6 versions use other sensors. It is not meant for the downstream port behind the converter, for the V6 engine or for the 1.5L turbo Accord that followed in 2018.

View DENSO Upstream AFR (Accord 2.4L 2013-17) on Amazon

curved road through a scenic mountain landscape

3. NTK Upstream Air-Fuel Ratio Sensor: Direct Fit for 2016-20 Honda Civic 2.0L

NTK Upstream AFR (Civic 2.0L 2016-20) product photo
Key features
  • Listed for 2016-2020 Civic 2.0L four-cylinder
  • Upstream air-fuel ratio sensor position
  • Genuine NTK part in original packaging
  • Direct replacement with hardware included

NTK, the sensor brand of the company behind NGK spark plugs, lists this air-fuel ratio sensor for the 2016 to 2020 Honda Civic with the 2.0L four-cylinder. It fits the upstream position, which on this engine is the sensor ahead of the catalytic converter that the engine computer relies on for its main mixture reading.

According to the listing it is a genuine NTK part supplied in its original packaging with hardware, built as a direct replacement rather than a universal sensor. The plug-in connector should match the car’s harness, so the job comes down to unplugging the old sensor, unthreading it and fitting the new one. A healthy upstream sensor keeps fuel trims close to where Honda intended, which helps the engine idle smoothly and hold its fuel economy.

It suits naturally aspirated tenth-generation Civics, which cover many LX and Sport trims, when diagnosis points to Bank 1 Sensor 1. Check the engine size on your registration or under the hood before ordering, because the 1.5L turbo Civic of the same years uses its own sensor. It is not a downstream part and does not suit earlier or later Civic generations.

View NTK Upstream AFR (Civic 2.0L 2016-20) on Amazon

4. NTK Upstream Air-Fuel Ratio Sensor: Direct Fit for 2017-20 Honda CR-V 1.5L Turbo

NTK Upstream AFR (CR-V 1.5L 2017-20) product photo
Key features
  • Listed for 2017-2020 CR-V 1.5L four-cylinder
  • Upstream air-fuel ratio sensor position
  • Genuine NTK part in original packaging
  • Direct replacement with hardware included

This NTK air-fuel ratio sensor is listed for the 2017 to 2020 Honda CR-V with the 1.5L four-cylinder, in the upstream position. That engine is the turbocharged unit fitted to most fifth-generation CR-Vs and the upstream sensor on it reads the exhaust before it reaches the converter.

The listing calls it a genuine NTK part in original packaging, with the hardware included and a direct-fit design. A factory-style connector matters on a compact SUV that spends winters on salted roads, because a spliced repair near the exhaust is a common place for corrosion to start. The upstream sensor feeds the engine computer the mixture reading it needs to adjust fuel delivery, so a slow or failed sensor can show up as poor economy, a rough idle or a stubborn check engine light.

Choose it when a scan points to Bank 1 Sensor 1 on a 1.5L CR-V and the wiring checks out. Run the car through the Amazon fit checker first, since the 2.4L CR-V sold in some years and the later hybrid use other parts. A slotted or offset sensor socket helps where access is tight. It does not suit the downstream position.

View NTK Upstream AFR (CR-V 1.5L 2017-20) on Amazon

vibrant macro shot of a metal screw surrounded by shavings

5. DENSO Downstream O2 Sensor: Direct Fit for 2010-13 Honda CR-V 2.4L

DENSO Downstream O2 (CR-V 2.4L 2010-13) product photo
Key features
  • Listed for 2010-2013 CR-V 2.4L four-cylinder
  • Downstream position, behind the converter
  • Genuine DENSO part in original packaging
  • Direct replacement with hardware included

This DENSO oxygen sensor is listed for the 2010 to 2013 Honda CR-V with the 2.4L four-cylinder, in the downstream position. That makes it the Bank 1 Sensor 2 part, mounted behind the catalytic converter, on the later third-generation CR-V, after its 2010 refresh.

The listing describes a genuine DENSO sensor in original packaging with the hardware included, sold as a direct replacement. Unlike the upstream air-fuel ratio sensor, this is a conventional heated narrowband sensor, and its main job is to watch how well the converter is working. The built-in heater brings it up to working temperature quickly after a cold start, which helps the emission monitors complete during short winter trips.

Use it when a heater circuit code such as P0141 or live data points to the rear sensor, and the connector and wiring look sound. Confirm the year and engine with the Amazon fit checker before ordering. A P0420 code on its own does not prove this sensor has failed, so check the converter and look for exhaust leaks first. It does not fit the upstream position or the 2007 to 2009 CR-V.

View DENSO Downstream O2 (CR-V 2.4L 2010-13) on Amazon

6. DENSO Downstream O2 Sensor: Direct Fit for 2006-15 Honda Civic 1.3L and 1.8L

DENSO Downstream O2 (Civic 2006-15) product photo
Key features
  • Listed for 2006-2015 Civic 1.3L and 1.8L
  • Downstream position, behind the converter
  • Genuine DENSO part in original packaging
  • Direct replacement with hardware included

This DENSO oxygen sensor is listed for the 2006 to 2015 Honda Civic with the 1.3L or 1.8L engine, in the downstream position. The 1.8L covers the mainstream eighth and ninth-generation Civic sedans and coupes, and the 1.3L appears in the 2006 to 2011 Civic Hybrid, so one part number reaches a large share of Civics on the road.

It is listed as a genuine DENSO part in its original packaging, with hardware included and a direct-fit connector. As a heated narrowband sensor behind the converter, it reports on catalyst health rather than steering fuel delivery minute to minute. The heater element helps it reach operating temperature soon after a cold start, which matters on a commuter car that rarely gets a long highway run in January.

It suits a Civic showing a downstream heater code such as P0141, or rear sensor data that stays flat when it should switch. Confirm the exact trim with the Amazon fit checker, since the Civic Si and other engines use different sensors. Because this sensor sits under the car behind the converter, it is often easier to reach than the upstream one, though rust can still lock its threads. It is not an upstream part.

View DENSO Downstream O2 (Civic 2006-15) on Amazon

Which Sensor Goes Where on Your Honda

The table pairs common generic codes with the sensor they usually point to on a four-cylinder Honda. Treat it as a starting point for diagnosis, because a code names the circuit that looked wrong, not always the part that failed.

CodeWhat it reportsSensor involvedCheck first
P2195 / P2196Upstream signal stuck lean or richBank 1 Sensor 1 (A/F sensor)Exhaust leaks ahead of the sensor, vacuum leaks
P0135Upstream heater circuit faultBank 1 Sensor 1Connector, wiring and fuse
P0141Downstream heater circuit faultBank 1 Sensor 2 (O2 sensor)Connector and harness near the exhaust
P0420Converter efficiency below thresholdRead by Bank 1 Sensor 2Catalytic converter and exhaust leaks
Common oxygen sensor codes on four-cylinder Hondas and where they point
breathtaking aerial view of vast grasslands spreading under a clear blue sky

The California Air Resources Board explains that the on-board diagnostic system watches nearly every emission component, lights the warning lamp when one misbehaves and stores details for the technician. Those stored details tell you far more than the code alone. A Honda-capable reader from our guide to scan tools for Honda shows the A/F sensor reading in real time.

Road Salt, Seized Threads and the Michigan Sensor Swap

A few West Michigan winters of brine and slush can weld a sensor into its boss. Soak the threads with penetrating oil the night before, warm the exhaust slightly, and turn the sensor with a slotted 22mm socket rather than an open wrench. Our roundup of the O2 sensor sockets that handle rusted sensors covers the offset and flex-head styles for tight upstream spots.

Before fitting the new part, clean the threads in the pipe, keep the sensor tip free of anti-seize and route the wire away from the hot pipe. Click the connector home, clear the code and drive normally so the monitors can run again.

serene misty hills with lush greenery and a winding dirt road

Rust also opens small holes and cracked joints, and air pulled in through a leak ahead of a sensor makes the mixture look lean. A short-term patch from our guide to the exhaust repair kit that suits your leak can hold a pipe for a while, but any leak near a sensor deserves a lasting fix.

Codes That Keep Coming Back After a New Sensor

If the light returns after a fresh sensor, even the best O2 sensor for Honda engines could not have fixed it. Intake leaks, a sticking injector, a damaged harness or a tired converter can all trigger the same codes, and a P0420 often belongs to the converter itself. Our page on bad catalytic converter symptoms shows what to watch for.

tranquil road lined with bare trees and green grass at sunset

A check engine light diagnostic in Grand Rapids reads the fuel trims and sensor data before anyone buys parts. When a sensor won’t come out, the threads are stripped or a pipe is leaking, our team handles exhaust repair in Grand Rapids on foreign and domestic vehicles.

Frequently Asked Questions

Is DENSO or NTK better for a Honda?

Neither wins across the board. Both supply sensors to carmakers and both sell direct-fit parts for Hondas, so the deciding factor is which maker offers a listing for your exact year, engine and position.

Can I put a regular O2 sensor where the Honda A/F sensor goes?

No. The upstream air-fuel ratio sensor uses a different signal and connector from a narrowband O2 sensor, so the engine computer cannot read a regular sensor in that position. Order a part listed as upstream for your engine.

Should I replace both oxygen sensors on my Honda together?

Only if both test bad. Swap only the sensor that the code and live data single out. On a high-mileage car some owners renew the upstream sensor on schedule, but a healthy downstream sensor can stay.

Will a new oxygen sensor clear a P0420 on a Honda?

Rarely. P0420 means the downstream sensor sees the converter storing too little oxygen, which usually points to the converter or an exhaust leak. Check the downstream sensor data before replacing anything.

Sensor code on your Accord, Civic or CR-V that won’t stay away? Ring 456 AutoFix at 616-279-3832 between 8am and 5pm, Monday to Friday, or request a diagnostic visit on our contact page.

If your workday overlaps our hours, bring the Honda to 456 Carrier St NE in Creston after we close and use the after-hours drop-off. A note with the keys about the code and when it appeared gives us a head start.