456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Civic, Accord, CR-V or Pilot? How to Pick the Best Wheel Bearing for Honda

best wheel bearing for honda: dynamic shot of a blue car captured in panning motion on a highway

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A worn Honda wheel bearing rarely fails all at once. It begins as a low drone on the highway that you blame on the tires, then turns into a growl that gets louder when you lean the car into a long on-ramp. The best wheel bearing for Honda drivers is the one listed for your model, generation and corner, from a maker that states exactly what it replaces.

Below are six listings for the Civic, Accord, CR-V and Pilot, sorted by the years and positions their Amazon pages name. Not sure the noise is a bearing? Read our explainer on how long wheel bearings last and what shortens their life before you spend money.

Quick answer

What wheel bearing should I buy for my Honda?

Match the part to your model, years and corner. Most Civic, Accord and CR-V fronts take a press-in bearing such as SKF FW78 or National 510118, while rears and the 2009-2015 Pilot front use bolt-on hubs like MOOG 513267. Check Amazon’s fit tool with your year, trim and drivetrain before ordering.

Our Quick Picks

Three listings that cover the most common Honda bearing jobs: the front of a Civic, the front of a newer Accord and the front of a 2009-2015 Pilot.

SKF FW78 product photo
Civic pick

SKF FW78

Front press-in bearing

An SKF cartridge bearing listed for front-wheel-drive Civics across several generations.

SuitsCivic owners with a front hum who can press bearings
View on Amazon →
National 510118 product photo
Accord pick

National 510118

Press-in bearing with encoder

A National cartridge bearing listed for the ninth and tenth generation Accord.

Suits2013-2020 Accord owners replacing a press-in bearing
View on Amazon →
MOOG 513267 product photo
Pilot pick

MOOG 513267

Front bolt-on hub assembly

A MOOG front hub listed for the second generation Pilot, no press needed.

Suits2009-2015 Pilot owners with front wheel noise
View on Amazon →

Press-In Bearing or Bolt-On Hub: How Hondas Differ

Honda builds its wheel ends two ways, and that decides both the part and the labor. On the front of most Civic, Accord and CR-V generations, the bearing is a sealed cartridge pressed into the steering knuckle and held by a snap ring. The hub flange then presses into the bearing, so replacing it means pulling the knuckle and using a press.

Rear wheels on these cars, and the front of the 2009-2015 Pilot, use a complete hub assembly instead. That unit carries the bearing, flange and studs together and bolts to the knuckle or trailing arm with four bolts. It costs more but goes in with hand tools.

When you shop for the best wheel bearing for Honda fronts, a part number hint helps: 510-series parts are bare bearings, 512-series are usually rear hubs and 513-series are usually front hubs. Treat that as a clue, not a fitment check.

Getting the Generation, Corner and ABS Right

Honda changes wheel-end parts between generations and sometimes between trims. Pin down these details first:

  • Model year and generation: a 2012 and a 2016 Civic share little at the wheels, so start with the exact year on your registration.
  • Trim and engine: Si, Type R, hybrid and V6 versions often take different bearings or hubs from the base car.
  • Drivetrain: FWD and AWD CR-Vs and Pilots can use different rear hubs, and some listings exclude hybrids outright.
  • ABS pickup: many Honda bearings carry a magnetic encoder for the wheel speed sensor, and it has to face the sensor when pressed in.

For trim names, engine options and model-year changes, the Honda Information Center model library helps you work out which generation you own. If you want a broader brand comparison first, our guide to the best wheel hub assembly brands and their part numbers covers Timken, SKF, MOOG, National and others.

Best Wheel Bearing for Honda: Six Listings by Model

Each listing names Honda models and years on its Amazon page, with the position noted wherever the listing gives it. No single bearing covers every Civic, Accord, CR-V or Pilot, so run your car through Amazon’s fit checker first.

1. SKF FW78: Front Wheel Bearing for Honda Civic FWD 2006-2019

SKF FW78 product photo
Key features
  • Front wheel bearing, sold singly
  • Listing names Honda Civic FWD 2006-2019
  • Press-in cartridge design
  • Made by bearing maker SKF

SKF FW78 is a front wheel bearing whose Amazon listing names front-wheel-drive Honda Civic models from 2006 to 2019. It is a bare cartridge bearing rather than a hub assembly, which matches how Honda builds the Civic front end: the bearing presses into the steering knuckle, a snap ring holds it in place and the hub flange presses through it.

The listing describes a bearing designed for smooth, low-friction rotation, made from wear-resistant materials and rated for a high load capacity. SKF is one of the large bearing manufacturers and supplies parts to many vehicle makers, so the FW78 number is widely cross-referenced in parts catalogs. Because it is only the bearing, the cost per corner is lower than a complete hub, but the labor is higher, since the knuckle has to come off the car and go on a press.

This bearing suits Civic owners, or the mechanic helping them, who have a press or a bearing press kit with the right adapters. The year range on the listing is broad, and Si, Type R and hybrid versions can use different parts, so confirm your year, trim and engine with Amazon’s fit checker before you order. If you want a bolt-on job instead, this is not the right part.

View SKF FW78 on Amazon

2. National 510118: Wheel Bearing with SureSignal Encoder for 2013-2020 Honda Accord

National 510118 product photo
Key features
  • Listing names 2013-2020 Accord
  • Also 2015-2020 Acura TLX
  • SureSignal magnetic encoders on both sides
  • Stainless steel flinger guards the seal

National 510118 is a wheel bearing whose Amazon listing names the 2013 to 2020 Honda Accord and the 2015 to 2020 Acura TLX. Like the Civic part above, it is a cartridge bearing that presses into the knuckle. The listing title does not state a position, but on these Accords the rear uses a bolt-on hub, so this style of bearing belongs at the front.

The standout feature is National’s SureSignal design, which puts a magnetic encoder on both faces of the bearing. On a one-sided bearing, pressing it in backward leaves the ABS sensor with nothing to read, and the warning lights come on. With an encoder on each side, that mistake is removed. The listing also mentions a heat-treated steel construction, a stainless steel flinger that shields the seal, and rolling elements engineered to meet or exceed the OE load rating.

This bearing suits Accord owners and home mechanics who are comfortable pressing bearings and want one less thing to get wrong at the ABS sensor. It does not suit anyone looking for a complete bolt-on hub. Hybrid and V6 Accords can differ, so check your year, trim and engine against Amazon’s fit checker before you buy.

View National 510118 on Amazon

close-up of a yellow crane hook inside a modern industrial facility

3. Detroit Axle Rear Hub Pair: Bolt-On Hubs for 2013-2015 and 2018-2023 Honda Accord

Detroit Axle Accord rear hubs product photo
Key features
  • Rear left and right hubs in one kit
  • Gas FWD Accord, not hybrid or SH-AWD
  • 5 lugs, 4-bolt square flange
  • Encoder-type ABS, 10-year listed warranty

This Detroit Axle kit contains two rear wheel bearing and hub assemblies, and the listing names the 2013 to 2015 and 2018 to 2023 Honda Accord with gas engines, plus the 2015 to 2020 Acura TLX with front-wheel drive. It states plainly that it does not fit hybrid models or SH-AWD versions of the TLX, which is the kind of detail that prevents a wrong order.

The listing gives the main specifications: rear left and right positions, five wheel studs, a four-bolt square mounting flange and an encoder-type ABS setup, where the wheel speed sensor reads a magnetic ring inside the hub. Because these are complete hubs, there is no pressing involved. You remove the brake parts, unbolt the old hub from the rear knuckle and bolt the new one in place. Detroit Axle lists a 10-year warranty on this kit.

This pair suits Accord owners who hear a rear hum and would rather do both sides at once, since the two corners have seen the same miles and the same salt. It is a value-focused brand rather than an OE supplier. The 2016 and 2017 model years are not named on the listing, so confirm your year and drivetrain with Amazon’s fit checker first.

View Detroit Axle Accord rear hubs on Amazon

4. SKF Front Wheel Bearing: Press-In Bearing for Honda CR-V 2007-2016

SKF CR-V front bearing product photo
Key features
  • Front position, named on the listing
  • Listing names CR-V 2007-2016
  • Genuine SKF part in original packaging
  • Sold through Sixity Auto

This SKF front wheel bearing is sold on Amazon by Sixity Auto, and the listing names the Honda CR-V from 2007 through 2016 at the front position. It covers two CR-V generations, which share the press-in front bearing layout used on many Hondas of that era. The listing describes it as a genuine SKF part supplied in original packaging, intended as a direct replacement.

As with the Civic and Accord bearings above, this is the bare bearing, not the hub. You remove the knuckle, press the hub flange out, take out the snap ring and press the old bearing out of its bore before pressing the new one in. The listing does not print an SKF part number in its title, so compare the outside diameter, width and ABS encoder ring on your old bearing with the new one before you install it.

This bearing suits CR-V owners with a front growl that shifts when the car leans in a turn, and a press or press kit to do the work. All-wheel-drive and front-wheel-drive models can use different parts at some positions, so confirm your year, drivetrain and engine with Amazon’s fit checker. If you want a bolt-on rear hub for a later CR-V, see the MOOG listing next.

View SKF CR-V front bearing on Amazon

detailed black and white image of industrial machinery with pipes and gears against a clear sky

5. MOOG 512501: Wheel Bearing and Hub Assembly for 2012-2016 Honda CR-V

MOOG 512501 product photo
Key features
  • Listing names 2012-2016 CR-V
  • Also 2013-2015 Acura RDX
  • Studs fitted, rust-resistant hub
  • Quad lip seal, sealed bearing

MOOG 512501 is a wheel bearing and hub assembly whose Amazon listing names the 2012 to 2016 Honda CR-V and the 2013 to 2015 Acura RDX. In common aftermarket numbering, 512-series parts are rear hubs, but this listing’s title does not name a corner and one of its bullets uses general front-hub wording. Confirm the position, as well as your drivetrain, in Amazon’s fit checker before you order.

The listing describes a sealed bearing designed for quiet running, a quad lip seal to keep moisture and debris out, a rust-resistant hub surface and wheel studs already installed. That last point matters in practice, since you bolt the whole unit to the knuckle instead of pressing studs or bearings. MOOG is a DRiV brand with a long catalog of steering and suspension parts, and it publishes the fitment on each listing.

This hub suits fourth generation CR-V owners who hear a hum from the back of the car and want a job that can be done with hand tools, a breaker bar and a torque wrench. It does not apply to the 2007 to 2011 CR-V or the 2017 and later models, which use different parts. Clean the mounting face on the knuckle so the new hub sits flat.

View MOOG 512501 on Amazon

6. MOOG 513267: Front Wheel Bearing and Hub Assembly for 2009-2015 Honda Pilot

MOOG 513267 product photo
Key features
  • Listing names 2009-2015 Pilot
  • Also 2007-2013 MDX and 2010-2013 ZDX
  • Bolt-on hub with studs installed
  • Quad lip seal, rust-resistant hub

MOOG 513267 is a front wheel bearing and hub assembly whose Amazon listing names the 2009 to 2015 Honda Pilot, the 2007 to 2013 Acura MDX and the 2010 to 2013 Acura ZDX. Unlike the Civic, Accord and CR-V fronts in this guide, the second generation Pilot uses a bolt-on front hub, so this part goes in without a press.

The listing describes a sealed bearing built for quiet operation, a quad lip seal against water and grit, a rust-resistant hub and studs already in place. On a heavier three-row SUV that tows and carries families, front bearings see a lot of load, and a complete hub replaces the flange and studs along with the bearing. MOOG lists clear fitment for each number, which makes cross-checking against the Acura models easier.

This hub suits Pilot owners whose front end drones at highway speed or who have found play when rocking the wheel by hand. It does not fit the 2003 to 2008 Pilot or the 2016 and later model, which use different front parts. Check your year and drivetrain with Amazon’s fit checker, and torque the axle nut and hub bolts to the figures in the service manual.

View MOOG 513267 on Amazon

Civic, Accord, CR-V or Pilot: Matching Each Listing

Use this table to narrow down the best wheel bearing for Honda models in your driveway, then confirm the fit on Amazon with your full vehicle details.

ListingType and positionModels the listing namesInstall style
SKF FW78Front bearingCivic FWD 2006-2019Press into knuckle
National 510118Bearing2013-2020 Accord, 2015-2020 Acura TLXPress into knuckle
Detroit Axle rear pairRear hubs, both sides2013-2015 and 2018-2023 Accord (gas, FWD), 2015-2020 TLX FWDBolt-on
SKF CR-V frontFront bearing2007-2016 CR-VPress into knuckle
MOOG 512501Hub assembly2012-2016 CR-V, 2013-2015 Acura RDXBolt-on
MOOG 513267Front hub assembly2009-2015 Pilot, 2007-2013 Acura MDX, 2010-2013 ZDXBolt-on
Honda wheel bearings and hubs in this guide, with the models, positions and install style each listing gives
detailed black and white photo of a man repairing a large industrial tire outdoors

Salt, Slush and Honda Wheel Bearings in West Michigan

Grand Rapids winters are hard on bearing seals. Months of brine work at the seal lips, and once moisture gets in, the grease breaks down and the races start to pit. The hum often shows up in spring, when dry roads make it easier to hear.

Freeze-thaw potholes can dent a bearing race in one hard hit. If you have been through a deep hole lately, our list of pothole damage signs to check after a hard hit walks through the tires, wheels and suspension too.

two men repairing an engine outdoors

Rust also seizes rear hub bolts and locks front bearings into the knuckle. Plan extra time and penetrating oil, and compare what you hear with our guide to wheel bearing noise symptoms so you replace the right corner.

Doing the Job Yourself or Handing It Over

A wheel bearing holds the wheel on the car, so treat it as a safety repair. Support the car on stands, follow the factory service manual for your model, and torque the axle nut and hub bolts to the figures it lists. Honda axle nuts are typically staked and should be replaced with new ones rather than reused.

vehicle drives on a frozen lake

Press-in fronts need a shop press or a press kit with the correct adapters, and pushing on the wrong race can ruin a new bearing. Our roundup of the best wheel bearing press kit options for home garages explains what to look for. If you would rather not wrestle a rusted knuckle, our wheel bearing replacement service in Grand Rapids works on foreign and domestic vehicles, Hondas included.

Pulling a knuckle disturbs the steering geometry, so have the alignment checked afterward, and our suspension repair service can inspect the rest of the front end.

Frequently Asked Questions

Do I need a press to replace a Honda front wheel bearing?

On most Civic, Accord and CR-V generations, yes. The front bearing is pressed into the knuckle, so you need a shop press or a bearing press kit with the right adapters. Bolt-on hubs, such as the 2009-2015 Pilot front, go in with hand tools.

Is a genuine Honda bearing worth the extra cost?

It is a safe choice, but not the only one. Bearing makers such as SKF, Timken and National list the Honda numbers their parts replace. Getting the correct part for your year, trim and corner matters more than the name on the box.

Why does my Honda still hum after a new wheel bearing?

The new bearing may have gone on the wrong corner, or it was damaged by pressing on the wrong race. Cupped or feathered tires can also drone like a bearing. Check each wheel for play and roughness and look at the tire tread before buying more parts.

Is your Civic, Accord or CR-V droning louder every week? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or ask for a wheel bearing inspection through our contact page.

Working the same hours we do? Our after-hours drop-off lets you bring the Honda to 456 Carrier St NE in the evening, so leave a note with the keys saying which side the noise seems to come from and at what speed it starts.