456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Which Loaded Rear Strut Fits Your Impreza? Gabriel vs FCS Struts

gabriel vs fcs struts: captivating view of a winding road through a snow-covered forest

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A tired rear end on a compact Subaru shows up as a hollow knock over frost heaves and a tail that keeps bobbing after a dip. Shoppers who want a strut that arrives already built often end up weighing gabriel vs fcs struts, because both brands sell loaded assemblies for a long list of older cars.

Brand pages alone make the two sound almost identical, so this guide pins both to one corner of one car: the rear of a 2008-2010 Subaru Impreza, where the Gabriel, FCS and Aisin listings below all overlap. Owners of other cars and crossovers can find a broader spread in our shocks and struts guide for daily drivers.

Quick answer

Which loaded rear strut suits a 2008-2010 Impreza, Gabriel or FCS?

Both are OE-style twin-tube assemblies that bolt in without a spring compressor. Pick the Gabriel ReadyMount G57703 if you want published specs and a listing that covers 2008-2014 cars. Pick the FCS 1345541 if you want the same application from a factory-direct maker. Aisin’s SAKF-01738 is a sound third option.

Our Quick Picks

A Gabriel and an FCS loaded rear strut for the same 2008-2010 Subaru Impreza, plus Aisin's rear assembly for that axle as a related third pick. All three are reviewed in full below.

Gabriel ReadyMount G57703 product photo
Gabriel pick

Gabriel ReadyMount G57703

Loaded rear strut, 2008-2014 Impreza

A fully built corner with published specs and wide year coverage.

SuitsOwners who like to check dimensions before buying
View on Amazon →
FCS 1345541 product photo
FCS pick

FCS 1345541

Loaded rear strut, 2008-2010 Impreza

A factory-direct complete assembly for the same rear corner.

SuitsOwners who have already confirmed the FCS number
View on Amazon →
Aisin SAKF-01738 product photo
Related pick

Aisin SAKF-01738

Twin-tube rear assembly, 2008-2011 Impreza

A third OE-style option that prints its Subaru reference numbers.

SuitsOwners who match parts by OE number
View on Amazon →

How Gabriel and FCS Build a Loaded Strut

Gabriel’s complete assemblies sit under the ReadyMount name inside its Ultra range. On the Gabriel ReadyMount page, the company says each unit ships with an upper mount, bumper, boot, coil spring, spring seat and a strut using its G-Force technology. It also states that every design is fit and ride tested on a vehicle, and that a pre-assembled strut can save up to an hour and a half of labor.

FCS Automotive takes a more industrial angle. Its FCS complete strut assembly page describes a vertically integrated maker with more than 60 engineers, and lists Freudenberg NOK seals, a hard-chrome piston rod, Eneos oil, nitrogen gas and electrostatically coated springs. FCS also says its coil springs match the original spring rate, so ride height and load capacity should stay where the car was designed to sit.

Where the two brands really differ

Mechanically, the gap is small. Both companies aim at the original ride rather than a sportier feel, and both ship a single corner that drops in with hand tools. The differences that matter to a buyer are quieter ones: how much detail the listing gives, how the warranty is handled and how easy it is to confirm the part number before you order.

On those points Gabriel’s Amazon listing is the more open of the two. It prints stroke, extended and collapsed length, mount codes and a long interchange list, and that list includes FCS part number 1345541. The FCS listing is brief, naming only the part number, its weight and a fit line for the 2008-2010 Impreza rear.

Why the Impreza rear makes a fair test

The third-generation Impreza uses a strut with the coil spring wrapped around it at each rear corner, so a worn unit can be swapped as one piece. It is a common car on Grand Rapids streets, many examples now carry high mileage, and none of our earlier shock or strut comparisons has used it. Because Gabriel itself cross-references the FCS number, the two parts are aimed at the same application.

The Three Rear Assemblies on Paper

The details below come from each Amazon US listing as it reads today. Where a listing leaves a field blank, the table says so instead of guessing.

DetailGabriel G57703FCS 1345541Aisin SAKF-01738
Years named in listing2008-2014 Impreza2008-2010 Impreza2008-2011 Impreza
PositionRearRearRear left and right
ConstructionLoaded strut, G-Force valvingLoaded strut, nitrogen gasTwin-tube, gas charged
Extended length17.13 inNot stated in listing17.72 in
Specs or references givenStroke, mount codes, interchange listPart number and weightSubaru OE reference numbers
Gabriel, FCS and Aisin rear strut assemblies for the 2008-2010 Subaru Impreza, from their Amazon US listings

The Gabriel and FCS listings are single units, so plan on two to do the axle. The small length gap between Gabriel and Aisin reflects how each maker measures and builds the part, not a change in ride height, so do not read too much into it.

Gabriel vs FCS Struts: The Impreza Rear Assemblies in Detail

Each part below goes on the rear axle of a 2008-2010 Subaru Impreza. Enter your year, body style, trim and drivetrain in Amazon’s fit tool before you order, because sport trims and wagons can call for a different part number.

Gabriel Ultra ReadyMount G57703: Loaded Rear Strut for 2008-2014 Subaru Impreza

Gabriel ReadyMount G57703 product photo
Key features
  • One rear strut and coil spring assembly for 2008-2014 Impreza
  • Pre-assembled, no spring compressor needed
  • G-Force ride control, fit and ride tested
  • Stroke 6.19 in, extended length 17.13 in

The G57703 is part of Gabriel’s Ultra ReadyMount family, the company’s line of complete strut assemblies. Its Amazon listing names the rear of the 2008-2014 Subaru Impreza and sells one unit per order, so buy two to renew the whole axle. Before you check out, enter your trim, body style and drivetrain in the fit tool, since sport versions of the car may use a different part.

Gabriel ships the strut with its coil spring, upper mount and related hardware already built up, so there is no spring to compress at home. The listing credits G-Force ride control and says the design is fit and ride tested. It also prints useful numbers: a 6.19 inch stroke, a 17.13 inch extended length, a 10.94 inch collapsed length and the mount codes, plus an interchange list that includes FCS part 1345541.

This assembly suits an Impreza owner who wants factory-style comfort back and likes to see the specs written down. The wider year range also helps if you own a 2011-2014 car, which the FCS listing does not name. It is not meant for a lowered car or one on sport springs, and drivers chasing a firmer feel should look at a performance strut instead.

View Gabriel ReadyMount G57703 on Amazon

solitary motorcyclist rides along a winding highway surrounded by lush trees

FCS 1345541 Complete Strut Assembly: Loaded Rear Strut for 2008-2010 Subaru Impreza

FCS 1345541 product photo
Key features
  • Complete rear strut assembly, part number FCS1345541
  • Fit line names the 2008-2010 Impreza rear
  • Nitrogen gas charged, springs matched to OE rate
  • Package weight 10.89 lb

FCS sells this unit under part number 1345541, and its Amazon listing gives a fit line for the rear of the 2008-2010 Subaru Impreza. The listing itself is short, naming the part number and a package weight of 10.89 pounds, so most of the detail comes from the maker. It helps that Gabriel’s own listing for the same corner cross-references this FCS number, which supports the fit for these years.

On its complete strut assembly page, FCS lists Freudenberg NOK seals, a mirror-finished hard-chrome piston rod and Eneos oil inside the strut. The bearing plate is endurance tested, the springs carry an electrostatic coating against corrosion, and the bumper is molded from urethane. Nitrogen gas reduces aeration and fade, and FCS states that each spring matches the original rate so ride height and load capacity stay as designed.

This is a sensible part for a 2008-2010 Impreza that needs its original ride back without a spring compressor. Because the listing names fewer years and fewer specs, confirm your part number with the FCS part finder or the Amazon fit tool before ordering. It is a single unit, so order a matching pair, and it is not designed for lowered or modified cars.

View FCS 1345541 on Amazon

AISIN Aftermarket SAKF-01738: Twin-Tube Rear Strut and Coil Spring Assembly for 2008-2011 Impreza

Aisin SAKF-01738 product photo
Key features
  • Rear strut and coil spring assembly for 2008-2011 Impreza
  • Gas-charged twin-tube construction
  • Lists the Subaru OE numbers it replaces
  • Installation manual included, extended length 17.72 in

The third pick stays on the same axle but comes from a different maker. Aisin’s aftermarket arm sells this preassembled strut and coil spring unit for the rear of the 2008-2011 Subaru Impreza, and the listing names the position as rear left and right. Check the quantity shown on the listing before you order, and confirm your trim and drivetrain in the fit tool as you would for the other two.

Aisin describes the unit as a strut, coil spring and upper components built into one piece, so several wear parts are renewed at once. The listing gives a gas-charged twin-tube design and a 17.72 inch extended length, and it prints a run of Subaru reference numbers in the 20310FG and 20365FG series. An installation manual comes in the box, and the maker says the part keeps proper ride height and stability.

This assembly suits owners who like to match parts against the Subaru number on the old strut or a parts diagram. It also covers 2011 models, which the FCS listing leaves out. As with the Gabriel and FCS units, it is built to restore the factory ride, so it is not the part for a lowered car or a driver who wants a sportier feel.

View Aisin SAKF-01738 on Amazon

close-up of coiled metal sheets in an industrial factory

Matching a Strut to How You Drive the Impreza

With three OE-style parts for the same corner, the choice comes down to paperwork and peace of mind more than ride feel. The table pairs each common situation with the listing that fits it most naturally.

Your situationCloser matchWhy
You want specs to compare before buyingGabriel G57703Lists stroke, lengths and mount codes
Your car is a 2011-2014 modelGabriel G57703Only listing here that names those years
You already know the FCS number fitsFCS 1345541Factory-direct part for the 2008-2010 rear
You match parts by Subaru OE numberAisin SAKF-01738Prints the OE references it replaces
Car is lowered or on sport springsNone of the threeAll are built for factory height
Gabriel vs FCS and Aisin matched to common Impreza owner needs
misty road through a foggy forest in autumn

On Subaru forums, owners who fit loaded rear struts mostly talk about how much quieter the rear becomes and how fast the job goes. Treat those posts as opinions, since tire wear, tire pressure and worn sway bar links change the feel of the car as much as the struts do. If you are also weighing Gabriel against other OE-tier names, our KYB and Gabriel CR-V comparison puts its ReadyMount against KYB’s Strut-Plus.

Fitting Loaded Rear Struts on the Impreza

A loaded assembly spares you from compressing the old spring, which is the most dangerous part of a strut job. Support the car on stands at the frame, remove the wheel and disconnect anything clipped to the strut body, such as a brake line bracket or sensor wire. Then the lower bolts and the upper mount nuts are all that hold the old unit in place.

Replace the struts as a pair, even when only one side knocks. A fresh unit on one corner and a worn one on the other can make the rear feel uneven over bumps and in turns. If you decide to buy bare struts and reuse your springs instead, read our coil spring compressor buying guide before you start, because a slipping compressor can cause serious injury.

van travels down a scenic tree-lined road under autumn foliage

Have the alignment checked after the job. Rear strut work can shift camber and toe slightly, and an Impreza that is out of spec will wear the inner edges of its rear tires. Torque every fastener to the figure in the service information with the car sitting on its wheels, so the bushings are not preloaded at full droop.

Salt, Frost Heaves and a Subaru Driven Year Round

Plenty of local Imprezas earn their keep in winter, which means months of brine on the rear suspension. The lower strut bolts sit right in the spray from the rear tires, so soak them in penetrating oil a day ahead and use a six-point socket. A bolt that will not budge is a good reason to stop before it snaps in the knuckle.

Spring thaw brings potholes, and worn rear struts let the car crash through each one and rebound twice. Whichever of the gabriel vs fcs struts options you choose, a loaded unit also renews the mount and bumper, which often wear as much as the strut itself here. Rinse the underside once salt season ends to slow rust on the new spring and brackets.

When a Mechanic Should Take a Look

Not sure the struts are the culprit? Our guide on how to tell if struts are bad walks through the bounce test, oily strut bodies and cupped tires. A creak or chirp over speed bumps can also come from bushings or end links, which our article on why a car squeaks when going over bumps covers.

peaceful dirt road winds through a colorful autumn forest with mountains in the background

Seized bolts, a knock that new struts do not cure or a rear end that wanders on the highway all point to a closer inspection. Our team handles suspension repair in Grand Rapids for foreign and domestic cars alike. Hendrick Hoffman holds ASE and State of Michigan credentials in steering and suspension, so a worn link or bushing hiding behind a strut complaint gets caught.

Frequently Asked Questions

Is Gabriel better than FCS for struts?

In the gabriel vs fcs struts question, neither brand is clearly ahead on ride. Both sell OE-style loaded assemblies that restore the factory feel. Gabriel’s listings usually give more specs and cover more years per part, while FCS sells factory-direct with a shorter listing, so confirm the part number either way.

Are FCS struts a good choice?

FCS lists Freudenberg NOK seals, a hard-chrome piston rod, nitrogen gas and springs matched to the original rate. For a daily driver that needs its factory ride back, that is a reasonable build. Check the fit carefully, since FCS listings on Amazon often give little more than a part number.

Do I need an alignment after replacing rear struts on an Impreza?

Yes, it is a good idea. Swapping rear struts can shift camber and toe slightly, and a rear that is out of spec wears the tire edges early. An alignment check after the job protects the tires and keeps the car tracking straight.

Can I fit a Gabriel strut on one side and an FCS strut on the other?

They may bolt on, but two brands can damp a little differently, which can make the rear feel uneven. Fit the same part number on both sides of an axle, and ideally the same brand and line on all four corners.

Impreza still knocking at the back after a strut swap, or not sure the struts are to blame? Ring 456 AutoFix on 616-279-3832 between 8am and 5pm, Monday to Friday, or request a rear suspension inspection on our contact page.

If your workday overlaps our hours, leave the Subaru with us through after-hours drop-off at 456 Carrier St NE, Grand Rapids, MI 49505, and we will pick up the job from there.