As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Look up a front wheel bearing for a 2010-2013 Mazda3 and two boxes keep coming up with the same 510102 number on them. That is where timken vs national stops being a forum argument and becomes a real choice: one name is a bearing company that has been around for well over a century, the other is a wheel end brand that sits inside a large parts group.
We kept the comparison narrow on purpose. Every bearing below is the press-in front cartridge bearing for the second-generation Mazda3, and every spec comes from the Amazon US listing or the maker’s own page. If you would rather compare complete bolt-on hubs across more brands, our roundup of wheel hub assembly brands by part number covers that ground.
Quick answer
Is a Timken or a National front bearing the smarter buy for a 2010-2013 Mazda3?
Both sell the same 510102 press-in bearing. Pick Timken if you want the listing that prints the Mazda and aftermarket numbers it replaces. Pick National if you like its stated build details, such as encoders on both faces and OE load rating. Confirm the number for your trim first, because some Mazda3s take 510096.
Our Quick Picks
One 510102 front bearing from each brand for the same 2010-2013 Mazda3, plus SKF's FW27, a number Timken's listing says its bearing replaces. All three are covered in full below.

Timken WB000026 Bearing
Bearing maker's cartridge that prints the numbers it replaces.

National 510102 Bearing
DRiV's wheel end brand, with encoders on both faces.

SKF FW27 Bearing
SKF's version of the number Timken says it replaces.
Who Stands Behind Each Name
Timken is a publicly traded engineering company best known for tapered roller bearings. Its company overview talks about more than 125 years of specialized expertise, and the page leads with industrial, aerospace and power markets. Passenger car bearings are a smaller slice of the business, sold through parts stores, repair shops and online.
National is a wheel end brand rather than a stand-alone company. The National brand page on the DRiV parts site calls it “DRiV Motorparts’ National brand” and says it has offered wheel end products for 75 years, covering wheel bearings and oil bath seals. Forum threads often claim other owners or factories, but the maker’s own page is the only statement we rely on here.
Neither company publishes where a given Mazda bearing is made on its Amazon listing. If country of origin matters to you, read the box when it arrives rather than trusting a post from years ago, since sourcing can change from one production run to the next.
What 510102 means on a Mazda3
On the second-generation Mazda3, the front bearing is a sealed cartridge pressed into the steering knuckle. The hub, which carries the wheel studs, is pressed through the center of the bearing, and a snap ring holds the bearing in its bore. Because nothing bolts together, the knuckle normally comes off the car so the old bearing can be pushed out and the new one pushed in.
The number 510102 is the common aftermarket interchange for this bearing, and Timken sells it as WB000026 while SKF calls it FW27. Parts catalogs are not unanimous, though, and some list 510096 for certain Mazda3 versions. Match the number to your VIN through the parts catalog or read it off the old bearing before you order.
Timken vs National on the Mazda3: Three Bearings Compared
All three bearings below are sold one per box, so a matched front pair means ordering two. They are listed against the 510102 number rather than one exact car, and Amazon’s fit checker with your year, engine and trim is the final word.
Timken WB000026 Wheel Bearing: Preset, Pre-Greased Sealed Unit Replacing Mazda GS3L33047 and 510102

- Preset, pre-greased and sealed bearing
- Replaces Mazda GS3L33047 and GS3L33047A
- Cross-references 510102, H510102 and FW27
- Sold as a single bearing, one per box
Timken sells this part as WB000026, a sealed cartridge wheel bearing for press-in front hubs. The title does not name a vehicle. Instead it lists what the bearing replaces: Mazda factory numbers GS3L33047 and GS3L33047A, plus aftermarket numbers FW27, 102421, 510102 and H510102. If the 510102 interchange matches your Mazda3 by VIN or by the number on the old bearing, this is the Timken version of that part.
The listing keeps its feature notes short. It describes the bearing as preset, pre-greased and sealed, which means there is no adjustment or packing to do, and the seals are meant to keep grease in and water out for the life of the part. The box holds one bearing, so a front pair means ordering two. Timken does not state a warranty term, load rating or country of origin here.
This suits owners who trust the Timken name and like checking a printed cross-reference before they buy. Plan on a new snap ring if the old one is distorted, and a new axle nut if the service manual calls for one. It does not suit anyone hoping to avoid a press, because like every 510102 bearing it has to be pressed into the knuckle.
View Timken WB000026 Bearing on Amazon

National 510102 Front Wheel Bearing: SureSignal Dual Magnetic Encoders, Heat-Treated Steel for 2005-2013 Mazda 3

- SureSignal magnetic encoders on both sides
- Heat-treated, premium-grade bearing steel
- Element size and count matched to OE load rating
- Title lists 2005-2013 Mazda 3
National’s 510102 is a sealed front wheel bearing that the listing title ties to the 2005-2013 Mazda 3, and it also names the 2008-2011 Dodge Avenger. Catalogs split some Mazda3 trims between 510102 and 510096, so treat the title as a starting point and confirm the number for your car before ordering. Like the Timken part, it is a single press-in cartridge, not a complete hub.
Where the Timken listing stays brief, National describes how the bearing is built. It says SureSignal technology puts magnetic encoders on both sides of the bearing to eliminate installation error, that the steel goes through an advanced heat treatment, and that the element size and quantity are engineered to meet or exceed the load rating of the original bearing. National also says its engineers test the design throughout development, though the listing does not publish results.
The two-sided encoder is the practical point for a home mechanic, since a bearing pressed in the wrong way round on a car that reads the seal can set an ABS light. The listing does not state a warranty or list Mazda factory numbers, so shoppers who rely on cross-references may prefer Timken’s sheet. You still need a press and the right adapters to install it.
View National 510102 Bearing on Amazon
SKF FW27 Wheel Bearing: Angular Contact Front Bearing for Radial and Axial Loads, Mazda 2009-2013

- FW27 front wheel bearing
- Angular contact design for radial and axial loads
- Low maintenance sealed design
- Title lists Mazda 2009-2013
SKF’s FW27 is the third maker’s take on the same bearing, and Timken’s own listing names FW27 among the numbers WB000026 replaces. The SKF title says it suits Mazda models from 2009 to 2013 without naming each car, so check it against your VIN and the old part. It is a single sealed cartridge bearing for a press-in front hub, sold one per box.
The listing explains the basic design more than the Timken one does. It describes an angular contact bearing, which supports both radial loads from the weight of the car and axial loads from cornering, and a low maintenance design meant for trouble-free running. SKF adds that it has been making ball bearings for more than 100 years. Like the others, the listing gives no warranty term, load figure or country of origin.
It suits a buyer who wants a long-established bearing maker but finds the Timken or National part out of stock, or who simply prefers SKF. The listing does not mention ABS encoders, so confirm how your car reads wheel speed before pressing it in. Installation is the same press job as the other two, with the knuckle off the car.
View SKF FW27 Bearing on Amazon

Reading the Two Listings Side by Side
The table uses only what each Amazon US listing states. Where a listing says nothing, the cell says so instead of filling the gap with a guess.
| Point | Timken WB000026 | National 510102 |
|---|---|---|
| Vehicle named in title | None, numbers only | 2005-2013 Mazda 3 |
| Numbers it replaces | GS3L33047, GS3L33047A, FW27, 510102, H510102 | Not listed beyond 510102 |
| Build details stated | Preset, pre-greased, sealed | Heat treated, premium-grade steel, OE load rating target |
| ABS encoder | Not stated | Magnetic encoders on both sides |
| Warranty in listing | Not stated | Not stated |
On paper, timken vs national comes down to what each listing chooses to tell you. Timken gives you a cross-reference sheet and very little else, which suits someone who shops by part number. National describes how the bearing is made but leaves out the factory Mazda numbers, so you lean on the 510102 interchange and the fit checker instead.
Choosing by How Long the Mazda Stays
Settling timken vs national for a Mazda3 starts with what the repair has to achieve. Most people replacing a front bearing want three things: the hum gone, no play in the wheel and no warning light on the dash. How long you expect to keep the car, and whether you are paying a shop for labor, usually matter more than the logo on the box.
| Your situation | Closer match | Why |
|---|---|---|
| You shop strictly by part number | Timken WB000026 | Prints the Mazda and aftermarket numbers it replaces |
| You worry about fitting the encoder the wrong way | National 510102 | Listing states encoders on both faces |
| You want a third maker on the same number | SKF FW27 | Named in Timken’s replacement list |
| Paying a shop to press it | Whichever you trust most | Labor is the same, so the part is a small share |
| ABS light came on with the noise | Diagnose first | A sensor or wiring fault can look like bearing trouble |
Labor changes the timken vs national math on this car. On a bolt-on hub, a cheaper part can make sense on a tired car because the swap is quick. A press-in bearing takes longer, and if a part fails early you pay for the knuckle to come off again, so many owners spend a little more on the part to avoid repeating the job.

When only one side hums, replacing just that bearing is a normal repair. The other side has seen the same miles and the same winters, though, so if it already shows any play or roughness it is worth doing both while the press and adapters are out. Our guide on how long wheel bearings usually last explains what wears them out and why mileage alone is a poor guide.
Pressing It In: Tools, Snap Ring and ABS
This is not a driveway job with hand tools alone. With the car on stands, the brake caliper and bracket come off and hang from the strut, the axle nut is broken loose, and the tie rod end, lower ball joint and strut bolts are separated so the knuckle can come out. Most people then take the knuckle to a bench press or a machine shop.
On the press, the hub is pushed out first, and the inner race of the old bearing often stays stuck on the hub and needs a separator or careful grinding to remove. The snap ring comes out, the old bearing is pressed from the knuckle, and the new one goes in by its outer race only. Our wheel bearing press kit guide explains the adapter sizes and why pushing on the wrong race damages a new bearing before it turns a mile.

Check how your car reads wheel speed before you seat the bearing. If the ABS sensor reads a magnetic encoder in the bearing seal, that face must sit toward the sensor, which is why National points out encoders on both sides of its part. Torque the axle nut and suspension bolts to the Mazda service manual figures, and plan on a wheel alignment because the knuckle came off.
Salt, Seized Knuckles and West Michigan Bearings
Front bearings on a compact front-wheel-drive car handle steering, braking and drive loads at once. In West Michigan, spring potholes add sharp impacts and road salt works at the bearing seal all winter. A seal that lets in salty water starts the corrosion that turns a quiet bearing into a growling one.
Salt also makes the repair harder on an older Mazda3. Ball joint and strut bolts can seize, the axle splines can rust into the hub, and the bearing bore in the knuckle can be crusty enough to scar a new bearing on the way in. Soak the hardware with penetrating oil the night before and clean the bore to bare metal before pressing.

After the job, listen at each seasonal tire swap. A low hum that changes as you weave gently left and right on the highway is the usual early sign, and rocking the tire top to bottom with the car in the air will show play long before the noise gets loud.
When the Knuckle Should Go to a Shop
Before buying anything, make sure the bearing is really the problem. Tire cupping can sound like a bad bearing, and a warning light may point elsewhere. Our page on wheel bearing noise symptoms covers the road tests, and our article on why the ABS light comes on explains the sensor faults that mimic a bearing.
No press, no adapters that fit the bore, or a knuckle too rusted to come apart cleanly are all good reasons to stop and call a shop. We handle wheel bearing replacement in Grand Rapids on foreign and domestic cars. Hendrick Hoffman is ASE and State of Michigan certified in steering and suspension and in brakes, and this repair takes in both systems.
More Buying Guides
Frequently Asked Questions
Who makes National wheel bearings?
National is a brand of DRiV Motorparts, according to the National page on the DRiV parts site, which says the brand has offered wheel end products for 75 years. Forum claims about other owners are common, so treat the maker’s own page as the reliable source.
Are Timken and National bearings the same part?
For timken vs national on the Mazda3, both are sold against the same 510102 interchange number, so they fit the same bore. That does not make them identical inside. Each maker sets its own materials, seals and testing, and neither listing publishes enough data to call one stronger.
Do I need a press to change a 2010-2013 Mazda3 front bearing?
Yes. The bearing is pressed into the steering knuckle and the hub is pressed through it, so you need a hydraulic press or a bearing press kit with adapters that match the bore. Many owners remove the knuckle and take it to a shop to be pressed.
Does every Mazda3 use the 510102 bearing?
No. Parts catalogs list 510102 for many 2010-2013 cars, but some list 510096 for certain Mazda3 versions, so one number does not cover every trim. Check your VIN in a parts catalog or read the number on the old bearing before you buy.
Hearing a hum from the front of your Mazda, or any car you drive around Grand Rapids? Call 456 AutoFix at 616-279-3832 on weekdays from 8am to 5pm, or set up a front bearing inspection on our contact page.
If your workday runs into our hours, bring the car to 456 Carrier St NE after we close and leave it with our after-hours drop-off. A short note about which side is noisy and when the sound started helps us get going.
