456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Lifted or Stock? How to Pick the Best Jack Stands for 4Runner Work

best jack stands for 4runner: serene rural landscape with barns at dusk along a winding country road

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A 4Runner sits higher and weighs more than the cars most jack stands are sized for, and many owners add lifts and bigger tires on top. The best jack stands for 4Runner work are the ones that reach its frame or axle without running out of ratchet bar, carry the load with room to spare and lock in a way you can see.

This page sticks to what is specific to the 4Runner, then reviews five pairs in detail. For the general buying advice on capacity, lock styles and saddles, start with our guide to jack stands for the home garage.

Quick answer

What jack stands should a 4Runner owner buy?

Measure from the floor to your support points first. A stock truck can often use a 3 ton pair such as the OTC S03G, which reaches 17-11/16 inches. Lifted trucks need taller 6 ton class stands like the OTC S06, and ESCO’s axle stands give the solid rear axle a wide base.

Our Quick Picks

Three quick picks for the common 4Runner setups: lifted, rear axle work and stock height. All five pairs are reviewed below.

OTC S06 product photo
Lifted trucks

OTC S06

6 ton · 15-5/8 to 23-11/16 in.

Tall, wide-footed steel stands built for heavier vehicles.

SuitsLifted 4Runners and bigger tires
View on Amazon →
ESCO 10497 Axle Stands product photo
Rear axle

ESCO 10497 Axle Stands

6,000 lb each · 13.2 to 21.5 in.

Square-footed axle stands sold for 4×4 and off-road trucks.

SuitsSolid rear axle work
View on Amazon →
OTC S03G product photo
Stock height

OTC S03G

3 ton · 12 to 17-11/16 in.

Compact geared stands for unmodified trucks and lighter jobs.

SuitsStock 4Runners and wheel jobs
View on Amazon →

How a 4Runner Is Built, and Why It Matters Under the Truck

The 4Runner is a true truck underneath. Toyota describes the fifth-generation 4Runner as body-on-frame, with a solid rear axle on four-link coil suspension. That layout gives you two strong places to hold the truck: the frame rails and the rear axle housing.

The newer generation keeps the separate frame. Toyota says the 2025 4Runner rides on its TNGA-F platform, shared with the Tacoma, Tundra, Land Cruiser and Sequoia, with strengthened frame crossmembers. Three things follow from all of this when you shop for stands:

  • Height: frame rails and axle tubes on a high-riding SUV sit well above a sedan’s pinch welds, so the stand’s top setting matters more than its lowest one.
  • Saddle shape: a V-notch or deep saddle cradles a round axle tube, while a flat or padded top suits a flat frame rail.
  • Footprint: a tall stand under a heavy truck needs a wide base so it stays planted when you work a stubborn bolt.

Stock Height or Lifted: Sizing the Stands to Your Truck

Ride height varies across the range even before owners change anything. Toyota notes that the fifth-generation TRD Pro gets about an inch of front lift from its Fox shocks and springs, and the 2025 Trailhunter comes on 33-inch tires with Old Man Emu shocks. Aftermarket lifts and larger tires raise the frame further still.

So skip the guesswork and measure. Lift one corner with your jack until the tire just clears the floor, then measure from the concrete to the frame rail or axle tube where the stand will go. Pick a stand whose working range puts that number in the middle of its travel, not at the very top notch.

Capacity is simpler. Check the gross vehicle weight on the label in the driver’s door jamb, then make sure the pair you buy is comfortably rated above the end of the truck it will hold. Many listings quote the rating for the pair, so read the wording carefully before you compare numbers.

Best Jack Stands for 4Runner: Five Pairs Compared

Each pair below comes from a known tool maker and covers a different need, from a stock SR5 to a lifted trail build. Capacities and heights are quoted as each Amazon listing gives them.

1. OTC S06: 6-Ton Steel Jack Stands with 23-11/16 in. Max Height

OTC S06 product photo
Key features
  • 6-ton capacity, sold as a set of 2
  • 15-5/8 to 23-11/16 in. height range
  • Self-locking ratchet handle, 11-tooth bar
  • Meets ASME PASE-2019

The OTC S06 is a heavy steel stand that OTC pitches at bigger work, such as step vans, vocational trucks and smaller heavy-duty vehicles. The listing gives it a 6-ton capacity for the set of two and a working range from 15-5/8 to 23-11/16 inches, which is the tallest top setting in this roundup.

That height is the main reason it suits a 4Runner. A lifted truck on larger tires can put the frame rails or axle tubes beyond the reach of a typical car stand, and the S06 still has adjustment left at that point. The base is formed and welded steel with an 11-9/16 by 10-3/8 inch footprint, and the welded foot pads are designed to resist sinking into asphalt or softer ground. Height is set with an 11-tooth ratchet bar, and OTC says the self-locking handle cannot be released while the stand is under load.

The saddle is a V-notch style, about 1.2 by 4.2 inches, which locates well on a frame rail edge or a pinch point. The listing states the stands meet ASME PASE-2019. For a stock truck that only needs 15 or 16 inches, the S06 may feel bulky, and its minimum height is too tall to slide under a low support point, so measure before choosing it.

View OTC S06 on Amazon

2. ESCO 10497: 6,000 lb Per Stand Axle Jack Stands with 12 x 12 in. Base

ESCO 10497 Axle Stands product photo
Key features
  • 6,000 lb capacity per stand, 2 stands
  • 13.2 to 21.5 in. with 10 positions
  • 12 x 12 in. powder-coated base
  • Tested to ASME standards (A2LA facility)

ESCO sells the 10497 as a performance axle stand for cars, trucks and 4×4 off-road vehicles, and that framing fits the 4Runner’s solid rear axle well. Each stand is rated at 6,000 pounds and the listing includes two, so the rating here is quoted per stand rather than for the pair.

The standout detail is the base. It measures 12 by 12 inches, broader than the pyramid feet on most ratchet stands, which gives a tall load a wider stance on the garage floor. The post is anodized and the base is powder coated, both aimed at resisting rust, a useful trait in a damp Michigan garage where road salt drips off the truck all winter. Ten height positions cover 13.2 to 21.5 inches, which spans a stock truck and many mildly raised ones.

ESCO says the stands were tested to ASME standards by an A2LA certified testing facility. The listing does not describe a double lock, so check each stand’s locking position carefully before going under the truck. Owners with a tall lift may find 21.5 inches short and should compare it with the OTC S06 or YELLOW JACKET 6 Ton.

View ESCO 10497 Axle Stands on Amazon

picturesque countryside road winds through lush greenery under a dramatic overcast sky

3. OTC S03G: 3-Ton Geared Jack Stands with 12 to 17-11/16 in. Range

OTC S03G product photo
Key features
  • 3-ton capacity, sold as a pair
  • 12 to 17-11/16 in. height range
  • Geared height adjustment
  • Meets current ASME PASE standards

The OTC S03G is the compact option in this list, a 3-ton geared stand sold as a pair. Its range runs from 12 to 17-11/16 inches, so it suits an unmodified 4Runner or a driver who mostly rotates tires, checks brakes or changes oil at stock ride height.

OTC pitches these stands as a companion to 2 and 3 ton service jacks, which is the size of jack many home mechanics already own. The geared design means height is set by a toothed mechanism rather than a loose pin, and the listing is clear that the stands are for support only and are not meant to lift a vehicle. OTC states they meet the newest ASME PASE safety standards and backs them with a limited lifetime warranty.

The trade-off is reach and margin. A lifted truck or one on larger tires can sit above the 17-11/16 inch top setting, and a 3-ton pair leaves less headroom over a heavy SUV than the 6 ton class stands below. Measure your support points first. If the number lands near the top of the range, move up to a taller pair instead of using the last notch.

View OTC S03G on Amazon

4. AME INTL 14361: 4-Ton Flat Top Jack Stands with Rubber Grips

AME INTL 14361 product photo
Key features
  • 4 ton capacity per stand, sold in pairs
  • 13.8 to 21.81 in. height range
  • Flat top with rubber grips
  • Triangular, powder-coated base

AME International sells its 14361 stands for trucks, SUVs and vans. The listing rates them at 4 tons per stand and stresses that they should always be used in pairs. Height runs from 13.8 to 21.81 inches, a range that covers a stock 4Runner and many trucks with a modest lift.

The feature that sets these apart is the top. Instead of a notched or V-shaped saddle, the 14361 has a flat surface with rubber grips at the lifting point. On a flat section of frame rail, that spreads contact over a wider area and helps protect a coated or freshly painted frame from steel-on-steel marks. The base is a stable triangular design with a powder coat finish, which helps it shrug off garage moisture.

A flat top is less suited to a round rear axle tube, where a cradle or deeper saddle holds the tube more securely, so a sensible plan is to use these on the frame and a different pair at the rear axle. The listing does not mention a secondary locking pin. Check that each stand is fully locked at the same height before lowering the truck onto it.

View AME INTL 14361 on Amazon

tranquil forest path after rain with a vibrant rainbow overhead

5. YELLOW JACKET 6 Ton: 13,000 lb Double Locking Jack Stands

YELLOW JACKET 6 Ton product photo
Key features
  • 6 ton (13,000 lb) capacity, 1 pair
  • 15-1/2 to 23-3/8 in. height range
  • Ratchet lock plus metal safety pins
  • Forged ductile iron ratchet bar

YELLOW JACKET’s 6 Ton pair is the other tall option here, with a range of 15-1/2 to 23-3/8 inches and a listed capacity of 6 tons, or 13,000 pounds, for the pair. That puts it close to the OTC S06 on reach, which makes it a good fit for a lifted 4Runner or a truck running larger tires.

Where it differs is the locking setup. The listing describes a double safety mechanism: the handle locks the ratchet bar, and a metal safety pin passes through the column as a backup. For anyone who spends long stretches under a truck, that second, visible lock adds peace of mind. The ratchet bar is forged from ductile iron in one piece, and the handle doubles as the release for the saddle column when you are ready to lower the vehicle.

The base is a wide stamped steel pyramid with a large top saddle, and the stands carry a limited one-year warranty. Like the other 6 ton class pairs, the minimum height of about 15-1/2 inches is too tall for low support points, so these suit raised trucks better than a stock one. Fit the pins every time rather than relying on the ratchet alone.

View YELLOW JACKET 6 Ton on Amazon

The Five Pairs Side by Side

Use this table to narrow down the best jack stands for 4Runner work, together with your own floor-to-frame measurement. If your number lands near the top of a range, step up to a taller pair.

StandsRated capacityHeight rangeSuits
OTC S066 ton (set of 2)15-5/8 to 23-11/16 in.Lifted trucks, bigger tires
ESCO 10497 axle stands6,000 lb per stand13.2 to 21.5 in.Rear axle work
OTC S03G3 ton (set of 2)12 to 17-11/16 in.Stock trucks, lighter jobs
AME INTL 143614 ton per stand13.8 to 21.81 in.Flat frame rails
YELLOW JACKET 6 Ton6 ton (13,000 lb) pair15-1/2 to 23-3/8 in.Lifted trucks, pin backup
Ratings and heights as stated on each Amazon listing. Measure your own truck before choosing.

Notice how the capacity wording changes from one maker to the next. ESCO and AME quote each stand, while OTC and YELLOW JACKET quote the pair, so line them up on the same basis before you decide which is stronger.

quiet open plain under a cloudy sky

If you also need a jack that reaches a high frame, our floor jack picks for Toyota owners cover lift range. Full-size pickups are covered in our jack stands for trucks roundup.

Getting a 4Runner Onto Stands in a West Michigan Garage

The routine is the same for every pair on this list. Take your time with it, since a tall truck on tall stands leaves less room for error than a sedan on short ones.

  1. Level concrete only: park on a flat slab, set the parking brake, put the transmission in park and chock the wheels that stay down.
  2. Lift where the manual says: your owner’s manual shows the jacking points for your model year. Raise the truck slowly and keep hands clear.
  3. Place the stands on solid metal: set them under the frame rails or the rear axle tubes, then lower the truck until its weight sits on the saddles.
  4. Check both locks: confirm the pawl is seated, fit any pin, and give the truck a firm push before you slide underneath.

Road salt is part of life here, and years of it can scale a frame. Before you trust a frame rail as a support point, look at it closely and tap away loose rust. If the metal is flaking or soft, choose a sound spot nearby and have the frame looked at.

dynamic light trails over a scenic lakeside view

A pair of stands is one part of a home setup that also needs a jack, chocks, a torque wrench and good light. Our list of car maintenance tools for beginners walks through the rest of that kit.

When the Truck Belongs on a Shop Lift

Stands are made for wheel swaps, oil changes, brake inspections and other short jobs. Work that pulls hard on suspension bolts, drops an axle or keeps the truck in the air for hours is safer on a two-post lift with proper adapters.

stunning view of a rural autumn field under dramatic rain clouds

Our factory scheduled maintenance service in Grand Rapids follows the intervals in your 4Runner’s maintenance guide with the truck up on a lift. If you hear clunks from the front end or notice uneven tire wear while you are under there, our suspension repair team can check the control arms and ball joints.

Frequently Asked Questions

Are 3 ton jack stands enough for a 4Runner?

For a stock truck they can be, provided the pair is rated above the weight of the end you are lifting and reaches your support points. Read whether the rating is per stand or per pair, and choose a 6 ton class pair if you want more margin or height.

Where do jack stands go on a 4Runner?

Use the frame rails or the rear axle housing, and follow the jacking and support points in your owner’s manual. Never set a stand under a suspension arm, the body or a skid plate.

Do I need taller stands for a lifted 4Runner?

Usually, yes. A lift or larger tires raise the frame, which can push your support points past the top of a 17 inch stand. Pairs like the OTC S06 or YELLOW JACKET 6 Ton reach about 23 inches.

What are the best jack stands for 4Runner rear axle work?

A stand with a cradle that holds a round axle tube and a wide base is the right shape. The ESCO 10497 axle stands are sold for 4×4 trucks and have a 12 by 12 inch base.

Prefer to have your 4Runner serviced on a proper lift? Phone 456 AutoFix at 616-279-3832 from 8am to 5pm on weekdays, or reach us through the contact page to arrange a visit.

If daytime drop-offs clash with your schedule, our after-hours drop-off is there for you. The shop is at 456 Carrier St NE, Grand Rapids.