456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Clunk Over Every Bump? The Best Control Arms for Ford SUVs and Sedans

best control arms for ford: stunning sunset views of a winding road in lush forested hills

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A worn control arm on a Ford crossover or sedan usually announces itself with a dull clunk over speed bumps, a steering wheel that wanders on the highway, or a front tire wearing on one edge. Choosing the best control arms for ford models comes down to three facts: which vehicle and generation you drive, which corner is worn, and whether the arm is a front lower, a rear link or a lift upper.

This guide covers the Escape, Explorer and Fusion, plus uppers for a lifted Bronco; F-150 owners have a separate guide. For background on the makers, see our overview of the control arm brands mechanics see most is a good starting point.

Quick answer

Which control arm should a Ford owner order?

Order a complete front lower arm with the ball joint installed, listed for your exact model, years and side: the MOOG RK622216 for a 2011-2019 Explorer, the Detroit Axle lower for a 2013-2019 Escape or the MOOG RK623001 for a 2013-2020 Fusion. A lifted Bronco needs lift-rated uppers. Confirm fit on Amazon first.

Our Quick Picks

Three listings that cover the most common Ford jobs: an Explorer lower, an Escape lower and lift uppers for a Bronco. Confirm year, side and drivetrain on Amazon first.

MOOG RK622216 product photo
Explorer lower

MOOG RK622216

Front left lower with ball joint

An OE-style MOOG lower arm for the unibody Explorer.

Suits2011-2019 Explorer and Police Interceptor Utility owners
View on Amazon →
Detroit Axle Escape Lower Arm product photo
Escape lower

Detroit Axle Escape Lower Arm

Front left lower with ball joint

A single driver side lower arm for the third-generation Escape.

Suits2013-2019 Escape owners replacing one corner
View on Amazon →
Rough Country Bronco Upper Arms product photo
Bronco lift uppers

Rough Country Bronco Upper Arms

Front upper pair, forged aluminum

Lift-rated upper arms for the full-size Bronco.

SuitsBronco 4WD owners running a 2.5-3.5 inch lift
View on Amazon →

Strut Front or Two Arms: What Your Ford Actually Has

The Escape, Explorer and Fusion in this guide all use a MacPherson strut at each front wheel. The strut does the job an upper arm does on a truck, so there is only one control arm per front corner: the lower arm. It carries the ball joint and two rubber bushings.

The Bronco is different. Its independent front end uses a short upper arm and a longer lower arm at each wheel, which is why Bronco owners shop for uppers when they lift the truck. At the rear, the Fusion and Explorer use multi-link setups with several smaller arms.

A clunk is not always the arm. Our guide to the warning signs of a failing control arm was written around Audis, but the symptoms it describes, such as knocking, vague steering and inner-edge tire wear, read the same on a Ford. A loose ball joint can feel similar, and our article on how a worn ball joint behaves helps you tell the two apart.

Sides, Generations and Look-Alike Models

Ford reuses names across very different vehicles, so the year range in a listing matters as much as the model. Check these points before you add anything to the cart:

  • Side: left (driver) and right (passenger) lower arms are mirror images with separate part numbers. A single-arm listing covers one corner.
  • Generation: a 2010 Explorer is a body-on-frame SUV, while a 2011 Explorer is a unibody crossover. Their arms do not swap.
  • Shared platforms: the Fusion arms also fit the Lincoln MKZ of the same years, and some Explorer arms also fit the Police Interceptor Utility.
  • Bronco Sport: it shares its platform with the Escape, not with the full-size Bronco, so Bronco lift arms will not fit it.

Best Control Arms for Ford: Escape, Explorer, Fusion and Bronco Picks

Every listing below names the Ford it was built for and the corner it replaces. Treat the stated years as the starting point, then confirm the exact year, model and engine on Amazon before you buy, because no single listing fits every version of these vehicles.

1. MOOG RK622216: Front Left Lower Control Arm and Ball Joint for 2011-2019 Explorer

MOOG RK622216 product photo
Key features
  • Front left (driver side) lower position
  • Listed for 2011-2019 Explorer and 2013-2019 Police Interceptor Utility
  • Ball joint and bushings come in the arm
  • Passenger side sold separately as RK622215

The MOOG RK622216 is a complete front lower control arm for the driver side of the fifth-generation Ford Explorer. The listing gives the fit as the 2011-2019 Explorer and the 2013-2019 Police Interceptor Utility, which share this unibody front end. It arrives as one assembly, with the ball joint and both inner bushings already in place.

On these SUVs the front strut handles the upper mounting point, so the lower arm takes most of the cornering and braking load at each wheel. When its ball joint loosens or the rear bushing tears, the usual symptoms are a knock over expansion joints and a steering wheel that needs constant small corrections. MOOG describes the arm as a part meant to hold suspension geometry where it belongs, supporting steering response and stable handling. Replacing the whole assembly avoids pressing out an old joint that has rusted into the arm.

This listing covers one corner only. The passenger side arm is a separate MOOG part, the RK622215, so plan two orders if both sides are worn. It will not fit a 2010 or older Explorer, which uses a different body-on-frame design, or the 2020 and newer model. Check your year and trim in Amazon’s fit checker, and book an alignment once the arm is installed.

View MOOG RK622216 on Amazon

2. Detroit Axle Front Left Lower Control Arm: Ball Joint Assembly for 2013-2019 Escape

Detroit Axle Escape Lower Arm product photo
Key features
  • Front left (driver side) lower position
  • Listed for 2013-2019 Ford Escape
  • One arm with the ball joint installed
  • Impact, wear and fatigue tested per the listing

Detroit Axle sells this front left lower control arm for the third-generation Ford Escape, listed for the 2013 through 2019 model years. The kit holds one arm with its ball joint already fitted, so it bolts in as a single unit at the driver side front wheel. It replaces the factory arm on a stock-height Escape.

The Escape is a compact crossover with a strut front suspension, which means this lower arm is the only control arm at each front corner. Its rear bushing tends to crack with age and road salt, and a worn bushing often shows up as a shudder under braking or a clunk when pulling away. Detroit Axle states that its suspension parts go through impact, wear and fatigue testing, and the listing also notes a ten-year warranty from the seller. The pre-installed ball joint saves pressing out a joint that may be seized.

The listing covers only the driver side, so a passenger side arm is a separate purchase. It is not listed for the 2020 and newer Escape or for the Bronco Sport, even though the Bronco Sport shares its platform with the newer Escape. Enter your exact year and engine in Amazon’s fit checker before ordering, and schedule an alignment once the new arm is torqued down.

View Detroit Axle Escape Lower Arm on Amazon

serene sunset paints the sky over a winding rural dirt road

3. MOOG RK623001: Front Left Lower Control Arm and Ball Joint for 2013-2020 Fusion

MOOG RK623001 product photo
Key features
  • Front left (driver side) lower position
  • Listed for 2013-2020 Fusion and 2013-2020 Lincoln MKZ
  • Also listed for Fusion-based police hybrid models
  • Passenger side sold separately as RK623000

The MOOG RK623001 is a front lower control arm and ball joint assembly for the driver side of the second-generation Ford Fusion. MOOG lists it for the 2013-2020 Fusion and the 2013-2020 Lincoln MKZ, along with the 2019-2020 Police Responder Hybrid and SSV Plug-In Hybrid. That covers gas, hybrid and plug-in versions built on this platform, as long as your exact model passes the fit check.

The Fusion uses a strut front end, so this arm is the single lower link that locates each front wheel. Sedans see a lot of highway miles, and a tired lower arm on a Fusion often shows up as a light shimmy at speed or tires wearing on the inside edge. MOOG describes the part as built to handle everyday road stress while helping keep the wheel alignment where it should be. Because it is a complete arm, you get fresh bushings at the same time as the new ball joint.

This listing is for one side only, and the matching passenger side arm is the RK623000. It does not fit the 2006-2012 Fusion, which uses a different front suspension and separate MOOG part numbers. Run your car through Amazon’s fit checker with the trim and drivetrain, then have the alignment set after installation.

View MOOG RK623001 on Amazon

4. Rough Country Forged Aluminum Upper Control Arms: 2-Pack for 2021-2025 Bronco 4WD, 2.5-3.5 Inch Lift

Rough Country Bronco Upper Arms product photo
Key features
  • Front upper pair for 2021-2025 Bronco 4WD
  • Made for a 2.5 to 3.5 inch lift
  • Forged aluminum with greaseable POM ball joints
  • Bolt-on install, listed at about 3-4 hours

Rough Country makes these forged aluminum front upper control arms for the 2021-2025 Ford Bronco 4WD, sold as a left and right pair. The listing names a 2.5 to 3.5 inch lift as the intended range, so they are a lift part rather than a factory-height replacement. For anyone searching for upper control arms for a Bronco, this is the type of listing to look for: one that states both the model years and the lift height.

The Bronco uses an independent front end with upper and lower arms, and raising it tilts the upper ball joint toward the end of its travel. These arms use POM ball joints that Rough Country says reduce friction, are fully greaseable and allow more joint movement than the factory arms. That extra range helps the suspension articulate off road and can give the alignment shop more room to set caster and camber. The listing describes a bolt-on install with no modifications, estimated at three to four hours.

On a stock-height Bronco or one with a small spacer lift, the factory uppers are usually still the right choice. These arms do not fit the Bronco Sport, which has a strut front suspension. Confirm your model year, drivetrain and lift height on Amazon, and plan a full alignment after fitting.

View Rough Country Bronco Upper Arms on Amazon

vast prairie landscape in Saskatchewan with a rural road and dramatic clouds at sunset

5. Metrix Premium Rear Upper Control Arm Kit: Left and Right Pair for 2006-2012 Fusion

Metrix Premium Fusion Rear Upper Kit product photo
Key features
  • Rear left and right upper arms, 2 pieces
  • Listed for 2006-2012 Fusion and 2007-2012 MKZ
  • Also listed for 2006-2011 Milan and 2003-2008 Mazda 6
  • Pre-greased steel arms, replaces RK641942

Metrix Premium Chassis Parts sells this two-piece kit with the rear left and rear right upper control arms for the first-generation Ford Fusion. The listing names the 2006-2012 Fusion, the 2007-2012 Lincoln MKZ, the 2006 Lincoln Zephyr, the 2006-2011 Mercury Milan and the 2003-2008 Mazda 6. It replaces the arm sold under the RK641942 part number.

These cars use a multi-link rear suspension, and the upper arms help set rear camber. When their bushings wear, the rear tires can start wearing on the inside edge and the car may feel loose over bumps in a turn. Metrix describes the arms as pre-greased steel parts and states that its parts are made to IATF 16949 and ISO 9001 quality standards. Getting both sides in one box keeps the rear end matched without hunting for a second listing.

This kit is for the rear of the car only and does nothing for front-end noises, which on a Fusion usually trace back to the front lower arms. It does not fit the 2013 and newer Fusion. Check your model, year and drivetrain in Amazon’s fit checker, and ask for a four-wheel alignment once the new arms are fitted.

View Metrix Premium Fusion Rear Upper Kit on Amazon

Matching Each Listing to Your Ford

This table restates the fit each listing gives; the fit checker makes the final call.

Vehicle and yearsCornerPiecesListing to check
Explorer 2011-2019Front left lowerOne armMOOG RK622216
Escape 2013-2019Front left lowerOne armDetroit Axle lower
Fusion 2013-2020Front left lowerOne armMOOG RK623001
Bronco 4WD 2021-2025, 2.5-3.5 inch liftFront upperPairRough Country forged uppers
Fusion 2006-2012Rear upper, both sidesPairMetrix Premium kit
Ford models, corners and piece counts matched to the control arm listings reviewed above

When you replace both sides, buying the same brand for each corner keeps the bushing stiffness and ball joint feel even. That matters more than which name is on the box, and it is the main thing that separates the best control arms for ford crossovers from a mismatched pair.

quiet rural road intersection with a stop sign in South Dakota's open plains

Bronco Upper Arms and Lift Height

On a Bronco at factory height, the stock upper arms are usually the right part, and owners on Bronco forums often keep them for small lifts. Once the front comes up around 2.5 inches or more, the upper ball joint runs near the end of its travel and the alignment may run out of caster or camber adjustment.

That is where lift-rated uppers come in. They are sold for a stated lift range, so match the arm to the lift you actually installed rather than the one you plan to add later. Shock length changes with a lift too, and our guide to picking shocks and struts for everyday driving explains how worn dampers make every bump harder on new arms.

Road Salt, Potholes and Ford Bushings

West Michigan winters are tough on lower arms. Brine sprayed off the road works into any tear in a ball joint boot, and once the grease turns to paste the joint loosens quickly. Spring potholes then hit the arm and bushings hard.

scenic view of expansive green fields and a clear sky during sunset with a visible road

A look at the boots and bushings at each oil change catches most damage before it turns into a clunk. MOOG notes on its control arm product page that a greasable socket lets fresh lubricant push contaminants out, so if your new arm has a fitting, give it a few pumps before the salt season starts.

Fitting, Alignment and When to Call a Shop

Bolting in a complete arm is simpler than pressing a ball joint, but it is still safety work. Support the vehicle on stands, torque every fastener to the factory figure, and tighten the bushing bolts with the suspension loaded at ride height so the rubber is not twisted when the car sits.

serene sunset over rural fields with a winding dirt road

Book an alignment right after the swap, since a new arm moves camber and toe. The Car Care Council’s guide to vehicle systems recommends checking steering and suspension at least once a year, usually along with a wheel alignment. Whichever of the best control arms for ford vehicles you choose, seized subframe bolts can turn a quick job into a long one, and our Grand Rapids suspension repair service can diagnose the noise and install the arm. The person checking your front end, owner Hendrick Hoffman, carries both ASE and State of Michigan certification for steering and suspension.

Frequently Asked Questions

Does a Ford Escape have an upper control arm in front?

No. The Escape, Explorer and Fusion covered here use a MacPherson strut up front, so each front corner has one lower control arm. Upper arms on these vehicles are found only in the rear suspension.

Can I replace just the ball joint instead of the whole arm?

On most of these Fords the lower ball joint comes as part of the arm, so the complete assembly is the usual repair. It also brings new bushings, which have often aged by the time the joint wears.

Should I replace both front lower arms together?

If both sides have the same miles and the second arm shows worn bushings or a loose joint, doing both saves a second alignment. If one arm was damaged by a pothole and the other checks tight, one side is a fair repair.

Do Bronco lift upper arms fit a Bronco Sport?

No. The Bronco Sport is built on the same platform as the Escape and uses a strut front end, so it has no front upper arms. Bronco upper arm kits are made for the full-size Bronco only.

Is your Ford knocking over potholes or drifting toward the shoulder? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a suspension check on our contact page.

Off work after five? Our after-hours drop-off at 456 Carrier St NE lets you leave the Ford overnight, and we will call you once we have had a look underneath.