As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A Lexus is built to feel quiet and planted, so a knock from the front end or a steering wheel that drifts off center stands out fast. Shopping for the best control arms for Lexus models comes down to three things: which Lexus you drive, which corner has worn out, and whether that arm carries its own ball joint.
This guide sorts listings for the GX470 and GX460, the RX crossovers, the ES sedan and the rear-drive IS. If you want background on the companies first, our overview of which control arm brands hold up is a good primer.
Quick answer
Which control arm should a Lexus owner order?
Match the arm to your model, corner and suspension type. A stock GX470 or GX460 suits the TRQ upper pair, a 2010-2020 RX350 without air suspension suits the Detroit Axle lower arm, and a 2007-2018 ES350 suits the Detroit Axle lower pair. Confirm year, side and trim on Amazon before ordering.
Our Quick Picks
Three listings that cover three common Lexus front end jobs: GX front uppers, an RX lower arm and an ES lower pair. Check your model year and side in the Amazon fit tool before ordering.

TRQ GX Upper Arm Set
A matched set of stock-style uppers for the body-on-frame GX.

Detroit Axle RX Lower Arm
A complete driver side lower arm for the third and fourth generation RX.

Detroit Axle ES Lower Pair
A matched pair of lower arms for the front-drive ES sedan.
Which Lexus Arm Is Worn, and Where It Sits
The GX is a body-on-frame SUV with an upper and a lower arm at each front wheel, the same layout as the 4Runner. The rear-drive IS also runs two arms per side, while the RX and ES use a strut with a single lower arm.
That layout tells you what to shop for. On a GX, the upper ball joint lives inside the upper arm, so a torn boot or a joint with play means a new arm. On an RX or ES, the lower arm takes the bumps, the braking load and the weight, and its rear bushing is the part owners most often find cracked.
Sway bar links, strut mounts and engine mounts can knock too, so rule them out first. Our write-up on symptoms of a failing control arm was written around Audis, but the noises, vibration and tire wear it describes apply to a Lexus just as well.
Four Fit Details That Trip Up Lexus Owners
Lexus model names often carry over between generations that share little underneath. Check these points against the listing title and Amazon’s fit checker before you add anything to the cart:
- Generation: a 2008 RX350 and a 2012 RX350 take different lower arms, and the listings below split exactly there.
- Air suspension: some RX trims came with air suspension, which changes the part on certain years.
- Drive layout: IS and GS arms are often listed for rear-drive cars only, so an AWD sedan may need something else.
- Single arm or pair: many listings hold one arm for one side, while kits hold both. Read the box contents line.
Best Control Arms for Lexus, Model by Model
Our six picks for the best control arms for Lexus models run from the GX down to the IS. Enter your Lexus in Amazon’s garage tool and read any trim notes before ordering.
1. TRQ Front Upper Control Arm Set: Both Sides with Ball Joints for GX470 and GX460

- Front upper arms for both sides in one kit
- Listed for 2003-2009 GX470 and 2010-2021 GX460
- Ball joints come pressed into each arm
- Pre-assembled, direct-fit replacement
This TRQ kit holds two front upper control arms, one for the driver side and one for the passenger side, each with its ball joint already installed. The listing names the 2003-2009 Lexus GX470 and the 2010-2021 GX460, along with the 2003-2021 Toyota 4Runner and the 2007-2014 FJ Cruiser, which all share this upper arm design. For owners looking for the best upper control arms for GX460 and GX470 trucks at stock height, a matched pair like this is the simplest route.
TRQ prints a long list of interchange numbers on the listing, including the Toyota numbers 4806629225 and 4806729225 and the aftermarket numbers 45D1260 and 45D1270. That makes it easy to compare against the arm you pull off or against a parts catalog. The arms arrive fully assembled, so there are no bushings or ball joints to press on the bench, and TRQ points buyers to its library of install videos for home mechanics.
This is a factory-style replacement, not a lift part, so a GX raised more than a couple of inches is better served by an arm made for that height. TRQ asks buyers to check Amazon’s confirmed fit result before ordering. Plan for an alignment once the new arms are bolted in.
View TRQ GX Upper Arm Set on Amazon
2. Metrix Premium RK620063/RK620064: Front Upper Arm Pair for GX470 and GX460

- Left (RK620064) and right (RK620063) front uppers
- Listed for 2003-2009 GX470 and 2010-2022 GX460
- Pre-greased ball joints, cotter pins included
- 3 year / 36,000 mile limited warranty
The Metrix Premium kit is a second option for the GX front uppers, again sold as a left and right pair. The listing covers the 2003-2009 Lexus GX470 and the 2010-2022 GX460, plus the 2003-2022 4Runner and the 2007-2014 FJ Cruiser. The box holds the front left arm, matched to the RK620064 number, and the front right arm, matched to RK620063, so the part numbers line up with common catalog references.
Metrix describes both arms as sheet metal construction, like the factory pieces, with ball joints that come pre-greased for smoother movement and a longer service life. Cotter pins are included for the ball joint nuts. The company says its parts come from IATF 16949 and ISO 9001 certified plants and are designed to meet or exceed the original specifications, and it backs them with a 3 year or 36,000 mile limited warranty from the date they go on the vehicle.
Like the TRQ set, these arms are meant for a GX at its original ride height rather than a lifted build. The listed GX460 span runs one year longer than the TRQ listing, which helps owners of later trucks. Confirm your model year and trim in Amazon’s garage tool, and have the alignment set after the swap.
View Metrix Premium GX Upper Kit on Amazon

3. Detroit Axle Front Left Lower Control Arm: Ball Joint Arm for 2010-2020 RX350

- Front left (driver side) lower position
- Listed for 2010-2020 RX350 and RX450h, 2018-2020 RX350L
- 2013-2020 fit excludes air suspension
- Ball joint pre-installed, 10-year warranty
This Detroit Axle listing is a single front lower control arm for the driver side, sold with the ball joint already installed. It names the 2010-2012 Lexus RX350, the 2013-2020 RX350 without air suspension, the 2018-2020 RX350L and several RX450h and RX450hL years. The same arm also fits the 2008-2019 Toyota Highlander and the 2009-2016 Venza, which share the platform.
The front lower arm on the RX takes the weight of the car, the braking loads and every pothole, and its rear bushing is a part owners often find cracked or separated. Replacing the full arm renews both bushings and the ball joint at once, which avoids pressing rubber on a bench. Detroit Axle states that its suspension parts go through impact, wear and fatigue testing, and its warranty and claims page explains how the 10-year coverage on the listing works.
Read the fitment line closely if your RX has air suspension, because the 2013-2020 coverage excludes those trucks. This listing is the left side only, and the passenger side arm is sold separately. Put your RX into Amazon’s fit checker before ordering, and follow the install with a wheel alignment.
View Detroit Axle RX Lower Arm on Amazon
4. Metrix Premium 527-003/527-004: Front Lower Arm Pair for 2004-2009 RX330 and RX350

- Front lower arms for both sides
- Listed for 2004-2006 RX330 and 2007-2009 RX350
- Also lists 2006-2008 RX400h and ES300/ES330 years
- Steel arms, 3 year / 36,000 mile warranty
Owners of the second generation RX need a different lower arm from the 2010 and later truck, and this Metrix Premium kit covers that earlier body. It holds a front left and a front right lower control arm, each with its ball joint fitted, under the reference numbers 527-003 and 527-004. The listing names the 2004-2006 RX330, the 2007-2009 RX350 and the 2006-2008 RX400h hybrid.
The same pair is also listed for the 2002-2003 ES300 and the 2004-2006 ES330, since those sedans share the lower arm with the RX of the same era, along with several Camry, Solara and Highlander years. The arms are steel and come with cotter pins for the ball joint nuts. Metrix states that its plants hold IATF 16949 and ISO 9001 certification and gives a 3 year or 36,000 mile limited warranty from installation.
Buying both sides in one box suits an older RX where both lower arms have covered similar miles on salted roads. These arms will not fit the 2010 and later RX350, which uses the Detroit Axle style arm above. Check the fit result for your year, and book an alignment once both arms are in place.
View Metrix Premium RX Lower Kit on Amazon

5. Detroit Axle Front Lower Control Arm Pair: Ball Joint Arms for ES350 and ES300h

- Two front lower arms, left and right
- Listed for 2007-2018 ES350 and 2013-2018 ES300h
- Ball joints pre-installed in both arms
- 10-year warranty per listing
The ES is a front-drive sedan with a strut front end, so the lower control arm carries most of the work at each front wheel. This Detroit Axle kit includes two front lower arms, one per side, with ball joints already pressed in. The listing names the 2007-2018 Lexus ES350 and the 2013-2018 ES300h hybrid, plus the 2005-2018 Toyota Avalon and listed Camry years built on the same platform.
On a high-mileage ES, the lower arm bushings tend to crack with age and road salt, which shows up as a clunk over bumps or a vague feel through the steering wheel under braking. Swapping complete arms renews the bushings and ball joints together in one job. Detroit Axle says its suspension line is put through impact, wear and fatigue testing, and the kit is backed by a 10-year warranty according to the listing.
Because the box holds both sides, it suits a car where both arms have aged together. It is not listed for the 2019 and later ES, which moved to a newer platform, or for the older ES330. Run your sedan through Amazon’s fit checker first, and plan an alignment after installation.
View Detroit Axle ES Lower Pair on Amazon
6. Detroit Axle Front Upper Control Arm Pair: Ball Joint Arms for RWD IS250 and IS350

- Two front upper arms with ball joints
- Listed for RWD IS250 2006-2015 and RWD IS350
- Also lists IS F, IS200t and RWD IS300 years
- 10-year warranty per listing
The rear-drive IS uses a double wishbone front suspension, so it has both an upper and a lower arm at each front wheel. This Detroit Axle kit replaces the two front upper arms, each with its ball joint. The listing names the 2006-2015 IS250 with rear-wheel drive, the 2006-2010 IS350, the rear-drive 2011-2020 IS350, the 2008-2014 IS F, the 2016-2017 IS200t and the rear-drive 2018-2020 IS300.
On these cars the upper arm ball joint is part of the arm, and a worn joint often shows up as a knock over sharp bumps or a slight shimmy at highway speed. Replacing both uppers at once keeps the two sides even, which matters on a sedan with quick steering. Detroit Axle states that its suspension parts are tested for impact, wear and fatigue, and the listing gives a 10-year warranty.
The fitment notes repeat the RWD limit for several years, so an all-wheel-drive IS250 or IS350 may need a different arm. Lower arm wear is a separate repair on these cars, so inspect those bushings while the front end is apart. Confirm your exact car in Amazon’s garage tool, then book an alignment.
View Detroit Axle IS Upper Pair on Amazon
Lexus Models Matched to Each Listing
Each row pairs a listing with the Lexus years it names, and the fit checker settles trim.
| Lexus model and years | Corner | In the box | Listing to check |
|---|---|---|---|
| GX470 2003-2009, GX460 2010-2021 | Front upper | Left and right arms | TRQ upper set |
| GX470 2003-2009, GX460 2010-2022 | Front upper | Left and right arms | Metrix Premium upper kit |
| RX350 2010-2020 (no air suspension) | Front left lower | One arm | Detroit Axle RX lower |
| RX330 2004-2006, RX350 2007-2009 | Front lower | Left and right arms | Metrix Premium lower kit |
| ES350 2007-2018, ES300h 2013-2018 | Front lower | Left and right arms | Detroit Axle ES lower pair |
| IS250 and IS350 RWD (listed years) | Front upper | Left and right arms | Detroit Axle IS upper pair |
For a Lexus not in the table, look for a listing that names your model, generation and corner rather than select Lexus vehicles. That habit matters more than brand when choosing the best control arms for Lexus cars outside this list.

Road Salt, Potholes and Lexus Bushings
West Michigan winters are hard on rubber and grease. Brine sprayed up from the road works into split ball joint boots, and repeated freeze-thaw cycles open potholes that load the lower arm bushings every spring. High-mileage bushings can look fine from above yet be cracked on the underside.
At each oil change, check the boots for tears, look for rubber pulling away from its sleeve and pry gently on the arm for movement.

Tired struts speed up arm and bushing wear, so see our guide to shocks and struts for commuter cars while the front end is apart.
Doing the Swap and Getting It Aligned
A GX upper arm is a reasonable driveway job with good stands and a ball joint separator. RX lower arms are harder: owners report that some years need the engine mount or subframe loosened to free the rear bushing bolt. On any Lexus, snug the bushing bolts first and torque them with the car at ride height so the rubber is not twisted.

Book an alignment as soon as the new arms are on, since they shift camber and caster. The Car Care Council’s guide to vehicle systems points to pulling, shaking and uneven tire wear as alignment warning signs. If seized bolts or a stubborn bushing get in the way, our Grand Rapids suspension repair service can check the whole front end and install the arms, and our owner, Hendrick Hoffman, holds ASE and State of Michigan certification in steering and suspension work.
More Buying Guides
Frequently Asked Questions
Do the GX470 and GX460 use the same upper control arms as the 4Runner?
For stock replacements, yes. The TRQ and Metrix listings in this guide name the 2003-2009 GX470, the GX460 and the 2003 and later 4Runner together, because the trucks share this front suspension. Lift arms can differ, so check each listing’s own notes.
What are the best upper control arms for GX470 owners who plan a lift?
A lift of about 2 inches or more usually calls for an arm built for raised trucks, which moves the ball joint back into its working angle and adds caster. The stock-style pairs reviewed here are meant for factory ride height. Check KDSS exclusions on any lift part before buying.
Why does my RX350 clunk over bumps?
A cracked rear bushing on the front lower arm is a common cause on the RX, but sway bar links, strut mounts and engine mounts can sound the same. Have the front end checked on a lift before buying parts.
Should I replace Lexus control arms in pairs?
When both sides have the same mileage and similar wear, a pair keeps the car steering evenly. If one arm was damaged in a pothole and the other side checks tight, replacing the bent one alone is reasonable.
Is your Lexus wandering in its lane or thumping over every expansion joint on the highway? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or ask for a Lexus front end inspection through our contact page.
Evenings work better for you? Park the Lexus in the after-hours drop-off at 456 Carrier St NE, jot down which corner knocks and on what kind of bump, and we will call you once the front end has been looked over.
