456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Loaded, Leveled or Adjustable: Best Struts for Tundra Pickups

best struts for tundra: view of a stunning sunset through a car window

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

A Tundra with worn front struts tends to wallow through dips, wander at highway speed and bounce a second time after every expansion joint. Picking the best struts for Tundra pickups starts with three facts about your truck: its generation, whether it is 2WD or 4WD, and whether it left the factory with the TRD package.

This guide covers front struts and coilovers for the 2007 to 2021 truck and the 2022 and newer redesign. If you also drive a sedan or crossover, our guide to shocks and struts for daily drivers covers those cars.

Quick answer

Which front struts should a Tundra owner buy?

Match the part to your model year, drive type and trim first. On a 2007 to 2021 truck, a loaded Monroe Quick-Strut restores factory height, a Rough Country N3 lifts the nose about 2 inches, and a 2022 or newer Tundra can take Bilstein’s height-adjustable B8 5100 front pair.

Our Quick Picks

Three quick picks: a loaded Monroe corner for 2007 to 2021 trucks at stock height, a Rough Country N3 for a 2-inch level, and a Bilstein B8 5100 front pair for the 2022 and newer Tundra. All six listings are reviewed below.

Monroe Quick-Strut 171119R product photo
Stock height, 2007-2021

Monroe Quick-Strut 171119R

Loaded strut · front right · 2007-2021 Tundra

A complete bolt-in corner that also renews the spring and mount.

SuitsSagging, high-mileage trucks kept at factory height
View on Amazon →
Rough Country N3 501090 product photo
2-inch level

Rough Country N3 501090

Loaded lifted strut · front · 2007-2021 Tundra

Raises the nose about 2 inches with the coil already installed.

SuitsOwners removing the factory rake
View on Amazon →
Bilstein B8 5100 Front Pair product photo
2022-2025, adjustable

Bilstein B8 5100 Front Pair

Bare monotube · front pair · 2022-2025 Tundra

Height-adjustable dampers for the redesigned truck.

SuitsOwners wanting firmer control or a mild level
View on Amazon →

Three Tundra Generations, Three Different Front Ends

Every Tundra rides on a coilover strut at each front wheel, while the rear has its own shocks. That means a strut order is a front-axle job, and the rear shocks are a separate purchase.

  • 2000 to 2006: the first-generation truck, with its own strut part numbers that do not cross over to later models.
  • 2007 to 2021: the long-running second generation with rear leaf springs. Many listings split 2WD and 4WD, and TRD package trucks often take a different strut.
  • 2022 and later: a new chassis. Toyota’s 2022 Tundra press release describes a new double wishbone front suspension, standard twin-tube shocks with triple oil seals and a multi-link coil-spring rear, with rear air suspension on some grades.

TRD Pro trucks carry their own factory performance dampers, and many aftermarket lift struts exclude them, as do some parts for trucks with rear air suspension.

Factory Ride, Level Stance or Firmer Control

  • Stock height and comfort: a loaded OE-style corner with a fresh spring and upper mount.
  • Level the rake: a lifted loaded strut or an adjustable coilover that raises the front roughly 2 inches.
  • Towing, plowing or dirt roads: a monotube or reservoir damper with stiffer valving.

Next, choose loaded or bare. A loaded strut arrives fully assembled and bolts in as a unit. A bare damper needs the old spring compressed and moved over, and a Tundra spring holds a lot of energy, so read our guide to the coil spring compressors suited to strut work before you try it at home.

Best Struts for Tundra: Six Front Listings Reviewed

Each listing names the years, side or drive type it covers; none fits every Tundra. Put your year, cab, bed, drive type and trim into Amazon’s fit checker, and always replace front struts as a left and right pair.

1. Monroe Quick-Strut 171119R: Loaded Front Right Strut and Coil Spring for 2007-2021 Tundra

Monroe Quick-Strut 171119R product photo
Key features
  • Listed for 2007-2021 Toyota Tundra
  • Strut, coil spring and upper mount preassembled
  • Spring calibrated to restore ride height
  • Coated steel with salt spray testing

The Monroe Quick-Strut 171119R is a complete front corner listed for the 2007 to 2021 Tundra. The R suffix marks the passenger side, and Monroe sells the driver side as 171119L, so plan on buying both and fitting them on the same day. Some trims and drive types within this long generation use other parts, so enter your year, cab, engine and trim in Amazon’s fit checker and read the qualifier notes before ordering.

Each unit ships with the strut, an application-specific coil spring and a premium upper mount already assembled. Monroe says the spring is calibrated to the original design so the truck returns to its factory ride height, and that the new mount helps with steering precision while cutting noise, vibration and memory steer. The steel carries a protective coating, and Monroe checks it with salt spray testing, which matters on a pickup that spends winters on salted roads.

The practical gain is a simpler, quicker repair. You remove the old corner and bolt this one in, with no spring compressor and no reused, worn rubber parts. It suits an owner whose truck has settled, clunks over bumps or floats on the freeway and who wants stock behavior back. It is not intended for lifting or leveling the front.

View Monroe Quick-Strut 171119R on Amazon

2. KYB SR4473 Strut-Plus: Complete Front Corner with Gas-a-Just Monotube for Tundra TRD Package

KYB SR4473 Strut-Plus product photo
Key features
  • Listed for Toyota Tundra with the TRD package
  • Strut, mount and spring preassembled
  • KYB Gas-a-Just monotube strut
  • Spring matched to the strut for ride height

The KYB SR4473 Strut-Plus is a complete front corner aimed at the Tundra with the TRD package, a trim that often needs a different strut than the base truck. KYB sells the opposite corner separately, with SR4472 listed alongside it, so check which side each part covers and order the matching unit. Confirm your model year, drive type and trim in Amazon’s fit checker, since KYB’s notes tie this part to specific builds rather than every Tundra.

Inside the assembly is a KYB Gas-a-Just monotube strut, the same style KYB describes as performance restoring for TRD package trucks. It comes preassembled with a mount and an application-engineered KYB spring that is matched to the strut. KYB says that pairing is meant to hold proper ride height longer and carry the weight of the truck without giving up ride quality.

This is a sensible pick when your TRD package truck feels loose, leans more than it used to or leaks oil at the strut body. Because it arrives complete, the swap needs no spring compressor and replaces tired mounts at the same time. It is built for original height and handling, so owners who want a level or extra lift should look at the leveling or coilover listings instead.

View KYB SR4473 Strut-Plus on Amazon

view of sunset cloudy sky with sunbeams through window of automobile riding along railing in countryside with

3. Rough Country N3 501090: 2-Inch Lifted Loaded Front Struts for 2007-2021 Tundra

Rough Country N3 501090 product photo
Key features
  • Listed for 2007-2021 Toyota Tundra
  • Lifts the front 2 inches without spacers
  • Preloaded coil, no strut disassembly
  • 1 3/8-inch bore, nitrogen charged

The Rough Country N3 501090 is a loaded front strut set listed for the 2007 to 2021 Tundra and engineered for a 2-inch lift. Rough Country offers a separate N3 lifted part, 501100_A, for 2WD trucks, so check your drive type, cab and trim carefully before ordering. Many lift struts also exclude certain special trims, which makes the fit checker and the listing notes worth reading in full.

Because the lift is built into the strut and spring, there is no need for a spacer on top of the factory part. The coil arrives preloaded, so you install the assembly as delivered without taking a strut apart. Rough Country uses nitrogen gas charging to limit oil aeration, a large 1 3/8-inch bore and a hardened, chromed piston rod for sealing and corrosion resistance. The listing also mentions a limited lifetime replacement warranty.

This listing suits a Tundra owner who dislikes the nose-down factory stance and wants room for slightly larger tires while keeping a ride close to stock. Expect to need an alignment afterward, since a taller front changes the steering geometry. It is not a match for trucks that must stay at factory height or for owners who want height they can adjust later.

View Rough Country N3 501090 on Amazon

4. Gabriel G57123 Ultra ReadyMount: Front Left Strut and Coil Spring for 2007-2020 Tundra RWD

Gabriel G57123 Ultra ReadyMount product photo
Key features
  • Listed for 2007-2020 Toyota Tundra RWD
  • Front left, sold as a 1-pack
  • Pre-assembled, no spring compressor
  • 5.7-inch stroke, G-Force ride control

The Gabriel G57123 Ultra ReadyMount is a loaded front left strut and coil spring assembly listed for the 2007 to 2020 Tundra with rear-wheel drive. It ships as a single unit, and Gabriel sells the front right side as G57124, so a complete front job takes both boxes. It is not listed for 4WD trucks, so a four-wheel-drive owner should skip it and choose a part that names that drive type.

The listing gives detailed specifications, including a 5.7-inch stroke, an extended length of 23.26 inches and a collapsed length of 17.55 inches, along with the upper and lower mount codes. That level of detail helps you compare it with your old part before you start. Gabriel describes the assembly as fit and ride tested, with its G-Force ride control tuning, and it includes the parts needed for a direct swap.

For a 2WD work truck that has gone soft up front, this is a practical bolt-in route back to stock height. Since the spring and mount come assembled, no spring compressor is involved and the job is reachable for a careful home mechanic. It is meant for factory ride, not for leveling, lifting or heavy off-road use.

View Gabriel G57123 Ultra ReadyMount on Amazon

assorted hand tools including wrenches and ratchets in a metal toolbox

5. Bilstein B8 5100 Front Pair: 0-2.3 Inch Adjustable Monotube Shocks for 2022-2025 Tundra

Bilstein B8 5100 Front Pair product photo
Key features
  • Listed for 2022-2025 Toyota Tundra
  • Front pair with 0-2.3 inch lift range
  • Digressive, velocity-sensitive valving
  • Zinc-plated body, limited lifetime warranty

The Bilstein B8 5100 front pair is listed for the 2022 to 2025 Tundra, the redesigned truck with a double wishbone front end. These are bare dampers with an adjustable spring seat that allows from 0 to 2.3 inches of front lift. Because they do not come with springs, the factory coils have to be compressed and moved onto the new bodies, and your trim, drive type and any air suspension should be confirmed in the fit checker first.

Bilstein uses digressive, velocity-sensitive valving that reacts as road conditions change, aiming for a ride that stays smooth yet controlled on pavement and rough ground. The company says each application is tuned through road testing for steering precision and control under changing loads. The shock bodies are zinc plated to resist rust and road salt, and the series carries Bilstein’s limited lifetime warranty.

This pair suits an owner of a newer Tundra who tows, drives gravel roads or wants a modest level without buying a full coilover kit. The height choice is set during assembly, so plan the spring seat position before you install them. It is not a bolt-in job for someone without a proper truck spring compressor, and it does not fit the 2007 to 2021 generation.

View Bilstein B8 5100 Front Pair on Amazon

6. FOX 2.0 Performance Set: Front Coilovers and Rear Reservoir Shocks for 2007-2017 Tundra

FOX 2.0 Performance Set product photo
Key features
  • Listed for 2007-2017 Tundra 2WD and 4WD
  • Front coilovers 985-02-004, rear 985-24-115
  • Adjustable from factory height to 2-inch lift
  • Front coilovers preset at 2 inches

The FOX 2.0 Performance set pairs two front coilovers, part 985-02-004, with two rear reservoir shocks, part 985-24-115, for the 2007 to 2017 Tundra. The listing covers both 2WD and 4WD trucks running factory height or up to 2 inches of front lift and 1 inch at the rear. Check your exact year and trim in the fit checker, because this set stops short of the last few years of the generation.

Front height comes from an adjustable preload ring, so you can run anywhere from stock up to a 2-inch lift, and FOX ships the coilovers preset at 2 inches. The coilovers arrive assembled with springs, which avoids a spring transfer up front. At the rear, the new shocks reuse the original rubber bushings and steel washers, since that hardware is not included. FOX backs the set with a limited one-year warranty.

This is a good fit for a Tundra that pulls a camper, carries gear on dirt roads or simply needs matched damping at both ends. Buying front and rear together keeps the truck balanced instead of pairing new struts with tired rear shocks. It goes beyond what a commuter at stock height usually needs, and setting the preload correctly takes care.

View FOX 2.0 Performance Set on Amazon

Which Listing Suits Your Truck

Use this table to narrow the best struts for Tundra trucks to one or two listings, then confirm the part number against your VIN.

Your TundraListing to checkTypeWatch for
2007 to 2021, sagging, keep stock heightMonroe Quick-Strut 171119RLoaded, per cornerOrder the 171119L left side too
2007 to 2021 with TRD packageKYB SR4473 Strut-PlusLoaded monotube cornerSingle corner; confirm the side
2007 to 2021, remove the front rakeRough Country N3 501090Loaded, 2-inch lift2WD trucks use a different part
2007 to 2020 RWD, stock heightGabriel G57123 Ultra ReadyMountLoaded, front leftNot for 4WD trucks
2022 to 2025, firmer controlBilstein B8 5100 front pairBare, height adjustableNeeds a spring transfer
2007 to 2017, tows or runs trailsFOX 2.0 Performance setCoilovers plus rear shocksReuses rear shock hardware
Tundra front strut listings compared by model years, drive type and strut style
view from inside a car at dusk

A noise up front does not always mean a bad strut. A chirp or creak over speed bumps often comes from a dry sway bar bushing or worn end link, and our article on why a car squeaks when going over bumps helps you separate the two.

Salt, Potholes and a Heavy Pickup in West Michigan

A full-size Tundra carries a lot of weight into every Grand Rapids pothole, and freeze-thaw season opens new ones each spring. Add a trailer, a loaded bed or a plow, and the damper seals wear faster.

Watch for a nose that keeps bobbing after a dip, hard dive under braking, cupped front tires and oily streaks running down the strut body. Our guide on how to tell if struts are bad covers the bounce test and the visual checks step by step.

blurry view of a peaceful traveler resting in a car with a dramatic sunset sky in the background

Road salt also seizes the lower strut bolts and top mount nuts, so soak them with penetrating oil a day ahead and have new nuts ready.

Fitting Tundra Struts and When a Shop Makes Sense

A loaded assembly is a reasonable driveway job with a floor jack, stands and a breaker bar. A bare damper like the Bilstein 5100 calls for a compressor rated for truck springs.

Whichever of the best struts for Tundra trucks you install, schedule a wheel alignment right after. New struts, and lifted ones above all, change camber and toe, and a pickup left out of spec pulls and wears the tire shoulders. Bilstein spells out its coverage on the Bilstein North American warranty page, which is useful reading before you choose a brand.

scenic drive at sunset with silhouetted mountains and a winding road

Prefer to hand the truck over? Our suspension repair service in Grand Rapids covers struts, shocks, mounts and the steering parts next to them. Owner and head mechanic Hendrick Hoffman is ASE and State of Michigan certified in steering and suspension, and our about us page tells his story.

Frequently Asked Questions

Do TRD package Tundras need different struts?

Often, yes. Many 2007 to 2021 listings name a separate part for trucks with the TRD package, such as KYB’s SR4473, so read the fitment notes and enter your trim in the fit checker.

Will a 2-inch leveling strut make my Tundra ride stiffer?

It may feel slightly firmer, because the spring and valving are set for a taller stance. A well-matched loaded strut keeps the ride close to stock, and an alignment afterward keeps the steering centered.

Can I fit 2007 to 2021 struts on a 2022 Tundra?

No. The 2022 redesign brought a new double wishbone front end, so it needs parts listed for 2022 and later trucks, like the Bilstein B8 5100 front pair.

Should the rear shocks be replaced with the front struts?

When both ends share the same mileage, doing them together usually pays off. Worn rear shocks let the back of the truck bounce, especially with a trailer hitched or weight in the bed.

Is your Tundra floating, diving or knocking over Grand Rapids potholes? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a front end inspection through our contact page.

Busy during our hours? The after-hours drop-off lets you leave the Tundra at 456 Carrier St NE, Grand Rapids, at whatever time suits your evening.