As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
The 4.0 liter inline six is the engine many Jeep owners refuse to give up, and its exhaust takes a beating from rocks, water and salt. When the old can rusts through or starts to rattle, finding the best muffler for Jeep 4.0 models comes down to two questions: which Jeep you drive and how you want it to sound.
This guide covers the Cherokee XJ and the Wrangler YJ and TJ, the three bodies most people mean when they talk about the 4.0. Below are six direct-fit mufflers and cat-backs listed for them. For a wider look at muffler styles on any vehicle, see our aftermarket muffler buying guide.
Quick answer
What muffler should a 4.0 Jeep get?
For stock sound, fit a direct-fit Walker muffler listed for your Wrangler or Cherokee year. For a deeper tone, a bolt-on stainless cat-back such as the Borla 14924 for a 2000-2006 TJ or the Flowmaster 717892 for an XJ is the simpler route. Always confirm year, body and drivetrain first.
Our Quick Picks
Three quick picks: a factory-sound muffler for later Wranglers, a stainless TJ cat-back and a stainless XJ cat-back. All six options are reviewed below.

Walker Quiet-Flow SS 21456
A direct-fit stainless muffler that aims for the factory note.

Borla 14924
A complete stainless cat-back with Borla's own sound.

Flowmaster 717892 FlowFX
A straight-through stainless cat-back with a deep tone.
XJ, YJ or TJ: Why the Body Matters More Than the Engine
Every Jeep in this guide can share the same 4.0 six, but the pipe that runs behind it does not. The Cherokee XJ has a long unibody with the muffler tucked under the rear floor, while the Wrangler YJ and TJ use a short frame with the muffler hung near the rear axle. A part built for one will not bolt onto the other.
Even inside the Wrangler family, the years split. Parts for 1997-2000 TJs often differ from 2000-2006 parts, and the longer Unlimited model from 2004-2006 has its own exhaust. Doors, drivetrain and a hitch can also change the listing.
Before you shop, write down four things: model year, body (XJ, YJ, TJ or Unlimited), drivetrain and whether the Jeep has a lift or a hitch. Then enter the full vehicle in Amazon’s fit checker and read any notes on the listing.
Stock Hush, Deeper Six or Full Cat-Back?
Replacement mufflers for these Jeeps fall into three groups. An OE-style muffler such as Walker’s Quiet-Flow SS or SoundFX copies the factory part and sound. A turbo-style muffler adds a little depth while staying mellow. A cat-back kit replaces the muffler and the pipes behind the converter, usually in stainless steel, and brings a stronger tone.
- Daily driver or long trips: stay close to stock, since loud mufflers on a boxy Jeep can drone at highway speed.
- Weekend trail rig: look at tailpipe routing and ground clearance as much as sound.
- Rusted pipes as well as muffler: a full cat-back often costs less effort than patching old pipe.
Sound descriptions below come from the makers and listings only. If in doubt, start quiet.
Best Muffler for Jeep 4.0: Six Picks for Wrangler and Cherokee
The first three picks are for Wranglers, the last three for the Cherokee XJ. Fit details come from each Amazon listing, so check year, body and drivetrain on Amazon before you order.
1. Walker Quiet-Flow SS 21456: Stainless Direct-Fit Muffler for 2000-2006 Jeep Wrangler

- Listed for 2000-2006 Jeep Wrangler
- 2.25 in outlet (ID)
- 100% stainless steel with internal drainage
- Louvered tubes for OE-style sound
The Walker Quiet-Flow SS 21456 is a direct-fit replacement muffler, and its Amazon listing names the Jeep Wrangler from 2000 through 2006. That span covers most TJ model years, including the 4.0 six, which makes it the natural choice when the original muffler has rusted out and you simply want the Jeep to sound the way it did from the factory. The listing gives a 2.25 inch outlet measured on the inside. Confirm your year, body and engine on Amazon before ordering, since the Unlimited and some trims can differ.
Walker builds the Quiet-Flow SS line entirely from stainless steel and adds an internal drainage system to reduce trapped moisture, which matters on a Jeep that sees short winter trips. Inside, OE-style louvered tubes and domed heads are meant to lower radiated noise, and Walker says the design was acoustic and flow tested for OE-style sound. Internal partitions and mechanically joined tubes allow the case to expand and contract as it heats and cools.
Hangers, brackets and pipe routing follow the original part, so the listing says no special fabrication or welding is needed. It is not the pick for owners chasing a deeper six-cylinder tone, and it only suits the Wrangler years the listing names.
View Walker Quiet-Flow SS 21456 on Amazon
2. Borla 14924: Stainless Cat-Back Exhaust for 2000-2006 Jeep Wrangler TJ 2.5L and 4.0L

- Listed for 2000-2006 Wrangler TJ 2.5L and 4.0L
- T-304 stainless steel, all welded
- Bolt-on installation
- 4WD two-door, includes Rubicon
The Borla 14924 is a complete cat-back exhaust system, so it replaces the muffler and the tubing from behind the catalytic converter to the tailpipe. Its listing names the 2000-2006 Jeep Wrangler TJ with either the 2.5 liter four or the 4.0 liter six, automatic or manual, four-wheel drive and two doors. Rubicon models are included, and the title says it suits Jeeps with or without a hitch. The longer Unlimited is not named, so check the fit tool on Amazon with your full vehicle details.
Borla lists T-304 stainless steel and all-welded construction, and the system is made in the USA. For a Michigan Jeep, stainless pipe is the main draw: aluminized steel usually gives up to salt sooner, and swapping the whole system at once means no new muffler is being clamped to tired old pipe. Borla describes the result only as its classic Borla sound, so expect more tone than stock rather than a factory-quiet exhaust.
The listing calls it a bolt-on installation. On a clean Jeep that can be a garage job, while seized converter studs on an older TJ may need heat or a shop lift. It does not suit owners who want stock sound.

3. Dynomax Super Turbo 17731: Mellow-Tone Muffler for 1987-1995 and 1997-2000 Jeep Wrangler

- Listed for 1987-1995 and 1997-2000 Wrangler
- Large internal flow tubes
- Patented flow director design
- Fiberglass matting for a mellow tone
The Dynomax Super Turbo 17731 is a turbo-style muffler listed for the Jeep Wrangler from 1987 to 1995 and from 1997 to 2000. Those years take in the square-headlight YJ, which got the 4.0 six from 1991, and the first TJ model years. The listing does not split the fit by engine, so enter your exact year, engine and trim on Amazon and read any notes before you buy. It is a useful option for older Wranglers, where many replacement parts are aimed at the later TJ.
Dynomax says the large internal flow tubes improve flow and reduce backpressure, and its patented flow director is meant to guide exhaust and cut turbulence on most applications. Fiberglass matting absorbs interior resonance, and the maker describes the sound as a mellow performance tone. The listing also states the design is dyno proven to flow up to 700 SCFM.
In practice, this is the middle ground between a stock-sounding can and a loud cat-back. It replaces only the muffler, so rusty tailpipe sections still need attention, and the case is not stainless steel. Owners who want a strong six-cylinder rumble may find it too tame.
View Dynomax Super Turbo 17731 on Amazon
4. Flowmaster 717892 FlowFX: 2.5 in Stainless Cat-Back for 1986-2001 Jeep Cherokee XJ

- Listed for 1986-2001 Cherokee XJ 2.5L and 4.0L
- 2.5 in 409 stainless tubing
- 3 in polished 304 stainless tip
- Straight-through FlowFX muffler
The Flowmaster 717892 FlowFX is a cat-back exhaust kit for the Jeep Cherokee XJ, and the listing names 1986 through 2001 with the 2.5 liter four or the 4.0 liter six, in two- or four-wheel drive. That wide range makes it one of the few kits on Amazon that covers nearly the whole XJ run. Body style and other details can still matter, so confirm the fit on Amazon with your full vehicle information.
The kit uses 2.5 inch 409 stainless steel tubing and finishes with a 3 inch polished 304 stainless tip. The muffler is Flowmaster’s FlowFX straight-through design, and the maker describes the sound as deep and powerful. According to the listing, the system uses the factory hanger locations and includes all the hardware, and Flowmaster calls it an easy at-home installation.
This is the pick for an XJ owner who wants a clearly stronger note and new stainless pipe in one job. A straight-through muffler on a long, boxy Cherokee can bring some highway drone, so it may not suit drivers who spend hours on the freeway. On a lifted XJ, check clearance at the rear axle and around the spare tire area before tightening the clamps.
View Flowmaster 717892 FlowFX on Amazon

5. Borla 140071: Stainless Cat-Back Exhaust for 1997-2001 Jeep Cherokee 4.0L

- Listed for 1997-2001 Cherokee 4.0L six
- T-304 stainless, all welded
- Two- and four-door, 2WD and 4WD
- Bolt-on installation
The Borla 140071 is a cat-back exhaust system for the later Jeep Cherokee XJ. Its listing names 1997 to 2001 models with the 4.0 liter six, automatic or manual, two- or four-wheel drive and two or four doors. That narrower range reflects the 1997 refresh of the XJ, so owners of earlier Cherokees should look at a different part. As always, enter your full vehicle details in the Amazon fit checker before ordering.
Like Borla’s Wrangler kit, this system is listed as T-304 stainless steel with all-welded construction, and it is made in the USA. On a Cherokee that lives through Grand Rapids winters, a full stainless system replaces the pipe sections that tend to rot along with the muffler. Borla describes the sound simply as its classic Borla sound, so plan on a more noticeable tone than the factory exhaust gave.
The listing calls this a bolt-on installation, which suits a home mechanic with good jack stands if the old hardware cooperates. It is not the part for an owner who wants the original quiet sound, and it does not cover XJs built before 1997.
6. Walker SoundFX 18568: Direct-Fit Factory-Sound Muffler for Jeep Cherokee, 2.25 in

- Listed for Jeep Cherokee XJ years
- 2.25 in inlet and outlet (ID)
- Aluminized steel with internal drainage
- Louvered tubes for factory-style sound
The Walker SoundFX 18568 is a direct-fit replacement muffler for the Jeep Cherokee, with a 2.25 inch inlet and outlet measured on the inside. Its fit list includes Cherokee years from 1987 to 1992 and from 1996 to 1999, among others. The listing does not name the engine in its title, so enter your exact year, engine and trim on Amazon and read the fit notes before buying. For an XJ owner who only needs the muffler, this is the plain, factory-style option.
SoundFX uses aluminized steel and an internal drainage system to help slow corrosion. Inside, louvered tubes reduce radiated noise for a factory-style sound compared with straight perforated tubes, according to the listing. Internal partitions and mechanically joined tubes let the parts expand and contract with heat, while spun-locked heads and OE-style spot welds hold the case together.
The hangers, brackets and pipe routing follow the original design, so the listing says no special fabrication or welding is needed. Aluminized steel usually wears faster than stainless in road salt, so it suits owners who want a quiet, low-effort fix over a long-term upgrade. It does not add any extra tone.
View Walker SoundFX 18568 on Amazon
Six 4.0 Jeep Mufflers Side by Side
The table sums up the listed fit and install type for each pick. If you are still deciding on the best muffler for Jeep 4.0 use, match the first column to your Jeep before you think about sound.
| Product | Listed fit | Sound as described | Type |
|---|---|---|---|
| Walker Quiet-Flow SS 21456 | 2000-2006 Jeep Wrangler | OE-style, factory-type sound | Direct-fit muffler |
| Borla 14924 | 2000-2006 Wrangler TJ 2.5L/4.0L, 4WD, 2-door | Classic Borla sound | Stainless cat-back |
| Dynomax Super Turbo 17731 | 1987-1995 and 1997-2000 Jeep Wrangler | Mellow performance tone | Direct-fit muffler |
| Flowmaster 717892 FlowFX | 1986-2001 Cherokee XJ 2.5L/4.0L | Deep and powerful | Stainless cat-back |
| Borla 140071 | 1997-2001 Cherokee 4.0L | Classic Borla sound | Stainless cat-back |
| Walker SoundFX 18568 | Jeep Cherokee, 2.25 in in and out | Factory-style sound | Direct-fit muffler |
A Wrangler owner who wants the stock note and a short job has the simplest choice: the Walker part for the matching years. Cherokee owners who also have rotten tailpipe sections should look hard at a full cat-back, because a new muffler clamped to thin old pipe rarely lasts.

Salt, Trails and the Michigan Muffler Rule
West Michigan winters are rough on old Jeeps. Road salt eats the hangers and clamps, and short trips leave water inside the muffler case that rusts it from within. Stainless cat-backs hold up better in salt than aluminized parts, and a can with internal drain holes helps on a Jeep that rarely gets a long highway run.
Trail use adds its own wear. A muffler hung low near the axle can be dented by rocks or soaked in creek crossings, so check the hangers after every off-road day. If seized exhaust bolts or a rusty frame are part of the job, our guide to the best rust remover for Jeep steel covers what helps.

Michigan’s vehicle code is clear on the basics. The text of MCL 257.707 says a motor vehicle “shall at all times be equipped with a muffler in good working order and in constant operation to prevent excessive or unusual noise,” and bars removing or damaging its baffles. Every product here is a muffler or a cat-back that keeps one, and we never suggest straight pipes or removing a catalytic converter. The EPA names cars and trucks as the largest outdoor source of carbon monoxide.
When the Noise Is Not the Muffler
On a 4.0 Jeep, a loud exhaust is often a leak further forward. A ticking at cold start can point to the manifold, and a hiss or fume smell under the floor can come from a cracked pipe or converter. Our article on exhaust leak symptoms explains what to listen for, and the catalytic converter guide for Jeep covers a worn converter.
If the muffler only has a small hole, a patch from our best exhaust repair kit review can buy some time. A clunk over bumps is often a failed rubber hanger rather than the can itself.

Even the best muffler for Jeep 4.0 engines will rattle if it hangs on tired rubber or leaks at a clamp. Our exhaust repair service in Grand Rapids covers mufflers, pipes, hangers and leak checks on foreign and domestic vehicles, so we can find the real source of the noise before you order parts.
More Buying Guides
Frequently Asked Questions
Does a Cherokee XJ muffler fit a Wrangler TJ?
No. Both can have the 4.0 six, but the XJ is a unibody with a different exhaust path, so mufflers and cat-backs are listed separately. Buy a part that names your exact model and years.
What is the quietest muffler for a 4.0 Jeep?
An OE-style direct-fit muffler, such as a Walker Quiet-Flow SS or SoundFX listed for your Jeep, aims to match the factory sound. Turbo-style mufflers like the Dynomax Super Turbo are described as mellow, while straight-through cat-backs are louder.
Will a cat-back fit a lifted Jeep?
Often, but not always. Listings are designed around stock height, so a lift, skid plates or other changes can affect clearance and hanger alignment. Expect a trial fit and possible adjustments on a modified Jeep.
Can I install a Jeep muffler at home?
A bolt-on cat-back or direct-fit muffler can be a home job if the old clamps and hangers come apart. On rusted Michigan Jeeps, seized bolts and thin pipe often turn it into shop work.
Is your Wrangler or Cherokee louder than it should be? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request an exhaust check on our contact page.
If your workday matches our hours, bring the Jeep to 456 Carrier St NE in Grand Rapids after closing and use the after-hours drop-off, with a short note on when the noise starts.
