456 Carrier St NE, Grand Rapids, MI 49505 Mon to Fri, 8:00am to 5:00pm. After-hours drop-off available 456autofix@gmail.com

Trucks, Camaros or Corvettes? The Best Muffler for Chevy 350 Engines

best muffler for chevy 350: interior of an industrial warehouse with stacks of metal pipes and high ceilings

As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.

The small-block 350 went into everything from square-body pickups to Corvettes, so there is no single answer for exhaust. The best muffler for Chevy 350 engines depends on which vehicle the engine sits in, what pipe it runs and how much noise you want on a long drive.

Below, we sort the 350 family by generation, explain when a full cat-back beats a single muffler, and review six options that name their fit. For a wider look at muffler designs, start with our aftermarket muffler buying guide.

Quick answer

Which muffler suits a Chevy 350?

Pick by vehicle first. A 1993-1995 Chevy truck takes a Flowmaster Force II kit, a 1996-1999 Tahoe fits MagnaFlow’s stainless Street Series, and LT1 Camaros and C4 Corvettes have their own bolt-on cat-backs. Classic cars with custom dual 2.5 inch pipe usually get a universal chambered muffler like the Flowmaster 40 Series.

Our Quick Picks

Three quick picks for the most common 350 setups: an OBS truck, an LT1 Camaro and a classic with custom pipe. All six are reviewed below.

Flowmaster 17147 Force II product photo
OBS truck

Flowmaster 17147 Force II

3 in · 1993-1995 5.7L

A complete truck kit with a mild to moderate tone.

SuitsDaily-driven and towing OBS pickups
View on Amazon →
Flowmaster 17143 American Thunder product photo
LT1 Camaro

Flowmaster 17143 American Thunder

3 in · 1993-1995 LT1

A bolt-on kit with a moderate outside tone.

SuitsFourth-gen Camaro and Firebird V8s
View on Amazon →
Flowmaster 40 Series 42543 product photo
Classic or swap

Flowmaster 40 Series 42543

2.50 in offset/offset

The original 40 Series bark for custom pipe.

SuitsC10s, Chevelles and Novas with dual 2.5 in pipe
View on Amazon →

One Engine, Many Exhaust Layouts

Chevrolet Performance confirms on its small-block engines page that the 350 belongs to the small-block family, and it still sells 5.7L 350 crate engines today. That long run is why exhaust parts are sorted by vehicle and year rather than by engine.

  • OBS C/K trucks: single exhaust, with different cat-backs for 1988-1992 and 1993-1995 models because of converter and cab changes.
  • GMT400 Tahoe and Yukon: single exhaust with a passenger-side rear exit on many 1996-1999 models.
  • LT1 cars: 1993-1997 Camaro and Firebird and the 1992-1996 Corvette use the LT1 version of the 350, each with its own pipe routing.
  • Classics and swaps: C10s, Chevelles and Novas often run custom dual pipes, usually 2.5 inch, built by a shop.

Write down the year, cab and bed length or body style before you shop. Many listings also note whether the truck uses a flanged or welded converter outlet, and that detail decides which kit bolts on.

Cat-Back Kit or a Single Muffler?

A cat-back replaces everything from the catalytic converter to the tailpipe. It comes as a set of mandrel-bent pipes, a muffler, hangers and clamps made for one vehicle, so it lines up with the factory hanger points. On a rusty 350 truck where the pipe is as thin as the muffler, a full kit is often the cleaner job.

A universal muffler is only the muffler. The pipe has to be cut and welded or clamped to suit, which makes it the usual route on classic cars with custom exhaust or on trucks where the pipes are still solid. Match the inlet and outlet size and whether each end is centered or offset.

Best Muffler for Chevy 350: Kits and Mufflers by Vehicle

Each listing below names its vehicle or its pipe size. Confirm year, model, cab, engine and converter type on Amazon before you buy, because one listing never covers every 350.

1. Flowmaster 17147 Force II: 3 Inch Cat-Back for 1993-1995 Chevy/GMC 5.7L Trucks

Flowmaster 17147 Force II product photo
Key features
  • Fits 1993-1995 Chevy/GMC 5.0L or 5.7L trucks
  • Flanged converter outlet required
  • 70 Series Big Block II muffler
  • 3 inch mandrel-bent aluminized tubing

The Flowmaster 17147 is a Force II cat-back kit listed for 1993-1995 Chevy and GMC trucks with the 5.0L or 5.7L engine and a flanged catalytic converter. It replaces the pipe, muffler and tailpipe behind the converter with 3 inch mandrel-bent tubing in 16-gauge aluminized steel. For a C1500 or K1500 whose factory system has rusted thin, that means one box instead of a pile of separate parts.

The muffler is Flowmaster’s 70 Series Big Block II, and the company describes the outside tone as mild to moderate. Flowmaster also calls the kit a good choice for towing, which matters on a truck that pulls a boat or a camper. The kit includes an aluminum heat shield, stainless steel clamps, hangers and hardware, and it uses the factory hanger locations, so the new pipe should follow the stock route under the cab and bed.

Fit depends on more than the year. Confirm cab style, bed length, two-wheel or four-wheel drive and the 5.7L engine on Amazon before you buy, and look at the converter outlet, since this kit needs a flanged one. A 1988-1992 truck takes a different Force II kit. Flowmaster covers it with a 3-year limited warranty.

View Flowmaster 17147 Force II on Amazon

2. MagnaFlow 15701 Street Series: Stainless Cat-Back for 1996-1999 Tahoe and Yukon 5.7L

MagnaFlow 15701 Street Series product photo
Key features
  • Fits 1996-1999 Tahoe and Yukon 5.7L
  • Single passenger-side rear exit
  • Stainless steel construction
  • Hardware included, limited lifetime warranty

The MagnaFlow 15701 is a Street Series cat-back system listed for the 1996-1999 Chevrolet Tahoe 5.7L and GMC Yukon 5.7L. It keeps a single exhaust layout and exits at the rear on the passenger side, so from behind the SUV it looks close to stock. For a GMT400 Tahoe that has spent many winters on salted roads, it is a complete replacement for the rusty pipes and muffler behind the converter.

MagnaFlow builds the system from stainless steel and describes the Street Series sound as resonant and throaty, tuned for both inside and outside the cabin. The company says 3D scanning was used during development to get fitment close to the original, and the kit includes the hardware needed for a do-it-yourself install. It is made in the USA and backed by MagnaFlow’s limited lifetime construction warranty, which is worth having on a vehicle that sees road brine for months each year.

Check your Tahoe or Yukon on Amazon before ordering: confirm the year, the 5.7L engine, two-door or four-door body and drive type. Other engine versions are not covered by this listing. If you want a quieter cabin than the Street Series offers, a stock-style replacement may suit you better.

View MagnaFlow 15701 Street Series on Amazon

beautiful landscape view of the Canadian Rockies with a clear highway and blue skies

3. Flowmaster 17143 American Thunder: 3 Inch Cat-Back for 1993-1995 Camaro and Firebird LT1

Flowmaster 17143 American Thunder product photo
Key features
  • Fits 1993-1995 Camaro and Firebird 5.7L LT1
  • 80 Series cross-flow muffler
  • 3 inch mandrel-bent aluminized tubing
  • Uses factory hanger locations

The Flowmaster 17143 is an American Thunder cat-back kit listed for the 1993-1995 Chevy Camaro and Pontiac Firebird with the 5.7L LT1 engine. The LT1 is a 350 small-block, but the fourth-generation F-body routes its exhaust very differently from a truck, so it needs its own kit. This one uses 3 inch mandrel-bent tubing in 16-gauge aluminized steel and replaces everything from the converter back.

Inside the kit is Flowmaster’s 80 Series cross-flow muffler. Flowmaster rates the sound as a moderate exterior tone with a mild interior tone, so it adds presence outside the car without filling the cabin the way a louder chambered muffler can. Hangers and hardware come in the box, and the kit uses the factory hanger locations, which keeps the pipes in the stock position under the floor and around the rear suspension.

The listing covers the 1993-1995 cars only. Flowmaster lists other kits for later LT1 cars, so confirm year, model and engine on Amazon before you buy. Aluminized steel holds up well but not as long as stainless in a salted Michigan winter, so a car driven year-round may need its clamps checked more often.

View Flowmaster 17143 American Thunder on Amazon

4. Borla 14385: T-304 Stainless Cat-Back for 1992-1996 Corvette C4 LT1 and LT4

Borla 14385 Cat-Back product photo
Key features
  • Fits 1992-1996 Corvette C4 5.7L LT1 and LT4
  • T-304 stainless steel
  • All-welded, bolt-on installation
  • Made in USA

The Borla 14385 is a cat-back exhaust system listed for the 1992-1996 Chevrolet Corvette C4 with the 5.7L LT1 or LT4 V8. Both engines are members of the 350 family, and the listing covers automatic and manual cars in coupe and convertible form. It replaces the factory system behind the converters with a Borla design that keeps the C4’s dual exhaust layout.

The system is made from T-304 stainless steel with all-welded construction, which Borla pairs with a bolt-on installation. Stainless of this grade is the most corrosion resistant common choice for exhaust parts, and it suits a Corvette that may see the odd wet spring drive even if it spends winter in storage. Borla describes the result simply as the classic Borla sound, and the system is made in the USA.

Before ordering, confirm on Amazon that your car is a 1992-1996 model with the LT1 or LT4 engine. Earlier C4 cars with the L98 350 are not covered by this listing. A bolt-on system still means working under a low car, so plan for ramps or a lift, and expect rusted factory hardware on a car that has seen Michigan roads in the past.

View Borla 14385 Cat-Back on Amazon

skilled welder in protective gear working on steel piping system with sparks flying

5. MagnaFlow 16710 Street Series: Stainless Dual Cat-Back for 1975-1979 Corvette 5.7L

MagnaFlow 16710 Street Series product photo
Key features
  • Fits 1975-1979 Corvette 5.7L
  • Dual split rear exit
  • Stainless steel construction
  • Hardware included, limited lifetime warranty

The MagnaFlow 16710 is a Street Series cat-back system listed for the 1975-1979 Chevrolet Corvette 5.7L. These late C3 cars carried the 350 small-block from the factory, and this kit keeps a dual layout with a split rear exit, one tip on each side. For a C3 owner replacing a tired or patched exhaust, it is a direct-fit option rather than a set of universal parts that need fabrication.

Like the other Street Series kits, it is built from stainless steel, and MagnaFlow describes the tone as resonant and throaty for both inside and outside the car. The company says 3D scanning helped it match the original fitment, and the kit includes all the hardware needed to install it. MagnaFlow backs its construction with a limited lifetime warranty, and it is made in the USA.

Many C3 Corvettes have been modified over the years, so check what is under yours before ordering. Confirm on Amazon that the year falls between 1975 and 1979 and that the car still has the 5.7L engine and a stock-style rear section. A car with headers or a custom mid-pipe may need a shop to adapt the joint.

View MagnaFlow 16710 Street Series on Amazon

6. Flowmaster 40 Series 42543: 2.50 Inch Offset/Offset Chambered Universal Muffler

Flowmaster 40 Series 42543 product photo
Key features
  • 2.50 inch offset inlet and offset outlet
  • Two-chamber design
  • 16-gauge aluminized steel, MIG-welded
  • No packing to blow out

The Flowmaster 42543 is the original 40 Series chambered muffler with a 2.50 inch offset inlet and a 2.50 inch offset outlet. It is a universal muffler, so it does not name a vehicle. Instead it suits the custom dual exhaust found on many 350-powered classics, such as a C10 pickup, a Chevelle or a Nova running 2.5 inch pipe on each side.

Flowmaster calls this its original muffler and describes the sound as a bold, aggressive bark. Inside is the classic two-chamber layout, and the case is 16-gauge aluminized steel that is fully MIG-welded. Because there is no packing inside, nothing can blow out or wear down over the years the way fiberglass packing can in a glasspack. Flowmaster aims it at muscle cars, street rods, trucks and custom builds.

Measure before you order. Check the outside diameter of the pipe ahead of the muffler and whether your pipe enters and leaves off center, since Flowmaster sells center and dual versions as separate listings. Fitting a universal muffler means cutting the pipe and welding or clamping it in place, which is usually shop work. On a highway commuter it can drone, so it fits a weekend car best.

View Flowmaster 40 Series 42543 on Amazon

Matching the Pick to Your Small Block

Use this as a starting point, then check the exact fitment notes on each listing.

VehicleOption hereTypeTone (maker’s words)
1993-1995 Chevy/GMC truck 5.7LFlowmaster 17147 Force II3 in cat-back, aluminizedMild to moderate
1996-1999 Tahoe or Yukon 5.7LMagnaFlow 15701Cat-back, stainlessResonant, throaty
1993-1995 Camaro or Firebird LT1Flowmaster 171433 in cat-back, aluminizedModerate outside, mild inside
1992-1996 Corvette LT1 or LT4Borla 14385Cat-back, T-304 stainlessClassic Borla sound
1975-1979 Corvette 5.7LMagnaFlow 16710Dual cat-back, stainlessResonant, throaty
Classic or swap with 2.5 in pipeFlowmaster 40 Series 42543Universal chamberedAggressive
Chevy 350 exhaust options compared by vehicle, type and stated tone
endless highway cutting through the Altai Mountains under a vast blue sky

If two picks fit your vehicle, choose by how you drive. A truck that tows or runs the highway every day is easier to live with on a milder kit, while a weekend Chevelle can carry a louder chambered muffler. The best muffler for Chevy 350 owners is the one that still sounds right after two hours at 70 mph.

Michigan Rules and Road Salt

Michigan’s vehicle code is direct about exhaust. Section 257.707c of the Michigan Vehicle Code says a person shall not drive on a highway or street with an exhaust defect that affects sound reduction, without a muffler or other noise dissipative device, or with a cutout, bypass, amplifier or similar device. Every option here replaces the factory muffler behind the converter, and we never recommend straight pipes, cutouts or removing emissions parts.

Salt is the other West Michigan problem. Brine and slush sit on the underside for months, and short trips leave water inside the muffler that rusts the case from within. Stainless kits such as the MagnaFlow and Borla systems resist that better than aluminized steel, though the hangers and clamps around them still wear.

diverse collection of stacked metallic pipes and rods in a warehouse display

Before a new system goes on, look at the parts it bolts to. A sagging tailpipe can come down to a broken exhaust hanger, and seized bolts at the converter flange come out easier after a soak with an exhaust rust remover. If the old muffler only has a pinhole, our post on a hole in your muffler covers what that means in Michigan.

When the Exhaust Job Belongs in a Shop

A bolt-on cat-back for a 350 truck or LT1 car is a reasonable driveway job with jack stands, penetrating oil and patience. A universal muffler is different, since the pipe needs cutting, expanding or welding to sit straight. Old trucks also hide rusted flange studs that snap the moment a wrench goes on.

If you smell exhaust in the cab or hear ticking near the manifolds, the leak may sit ahead of the muffler, and our list of exhaust leak symptoms helps narrow it down. A short-term exhaust repair kit can seal a small crack until the real fix.

winding road through Hol

Our exhaust repair service in Grand Rapids handles mufflers, pipes and hangers on domestic and foreign vehicles. If you are torn between two kits, we can look at the truck or car and tell you what the existing pipe and hangers will support.

Frequently Asked Questions

What size exhaust does a Chevy 350 use?

It depends on the vehicle. Many truck cat-backs for the 5.7L use 3 inch tubing, while classic cars with dual exhaust commonly run 2.5 inch pipe on each side. Measure the outside of the pipe ahead of the muffler before ordering a universal unit.

Is a Flowmaster 40 Series too loud for a daily driver?

Flowmaster describes the 40 Series as aggressive, and many owners find it tiring on long highway drives in a truck. A milder kit such as the Force II, or a straight-through design, is easier to live with every day.

Can I use a cutout on my 350 in Michigan?

No. Michigan’s vehicle code bars driving on a street or highway with a cutout, bypass or similar device, or without a muffler. Keep a working muffler in the system on any street-driven vehicle.

Does a 1990 Chevy truck take the same cat-back as a 1994?

Usually not. Flowmaster lists separate kits for 1988-1992 and 1993-1995 trucks, and cab, bed length and converter type also change the fit. Check each detail on the listing before buying.

Want the best muffler for Chevy 350 trucks or cars fitted without a fight over rusted studs? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up an exhaust visit on our contact page.

Stuck at work until five? Our after-hours drop-off means the Chevy can come in once your shift ends. Look for 456 AutoFix at 456 Carrier St NE, Grand Rapids, on the Creston side of town.