As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A ball joint is a small part with a big job: it lets the steering knuckle pivot and swing while it carries the weight of the car. The best ball joints are the ones built for your exact car and position, from a maker that publishes how the joint is put together.
This guide covers what separates a solid replacement from a weak one, how the big brands compare and six specific listings for the Camry, Civic, Accord, Equinox and CR-V. If you are not sure the joint is the problem yet, our article on bad ball joint symptoms walks through the warning signs.
Quick answer
Which ball joint should I buy for my car?
Buy the part number made for your car, axle and side. MOOG suits a Camry or Equinox, TRW covers the 2012-2015 Civic and 2003-2007 Accord, and Mevotech Supreme adds a grease fitting on the CR-V. Confirm year and trim in Amazon’s fit checker, then have the alignment checked afterward.
Our Quick Picks
Three listings that cover the most common jobs: a lower joint for the Camry, a lower joint for the Equinox and a greasable joint for the CR-V.

MOOG K500044
A MOOG lower joint for the long-running sixth and seventh generation Camry.

MOOG K500227
A separate lower joint for a crossover that often gets a full arm instead.

Mevotech Supreme
A serviceable joint for Honda's small crossovers.
How a Quality Ball Joint Is Built
Inside the housing, a hardened steel ball stud sits in a bearing that lets it rotate and tilt. A rubber boot keeps water and grit out and holds the grease in. Once that boot splits, road spray gets in, the bearing wears, and the joint starts to knock or let the wheel wander.
The differences between brands come down to a few details:
- Bearing material: polymer bearings run smoothly when new, while powdered-metal or sintered bearings are made to resist wear and can pass fresh grease.
- Sealed or greasable: a sealed joint is lubricated for life, and a greasable one has a fitting so you can push out old grease and moisture at each oil change.
- Boot quality: a thick boot that seats tightly on the housing and stud protects the joint for longer.
- Hardware: a castle nut and cotter pin, or a new lock nut, should come in the box.
MOOG explains these features for its own range on the MOOG ball joints page, including its sealed boot with a grease-relief valve and its powdered-metal gusher bearing. Not every MOOG part number gets every feature, so read the listing for the joint you are buying.
Also check how the joint mounts. Some bolt to the control arm, many Honda lower joints press into the knuckle and sit behind a snap ring, and some factory joints are riveted to the arm. A pressed-in joint needs a C-frame press, and a riveted one may make a complete control arm the simpler repair. Our guide to control arm brands for everyday cars covers that route.
MOOG, OEM, ACDelco and the Other Big Names
Shoppers often compare MOOG with the factory part. A dealer joint matches what the car left the plant with, usually sealed and with no grease fitting. MOOG and Mevotech often add a fitting or a different bearing design, which some owners like and others don’t need.
ACDelco is GM’s parts brand, sold in Gold and Silver lines, and fits GM vehicles first. TRW, now under ZF, supplies factory parts to many carmakers and sells an aftermarket line. Detroit Axle sells joints in pairs and kits, while Proforged and store brands such as Duralast fill out the rest of the shelf.
For a daily driver, the best ball joints are simply the correct part number from one of these makers, installed and torqued properly.
Best Ball Joints for Common Cars and Crossovers: The Picks
Each pick lists the vehicles and position its Amazon listing names. A different year, side or trim often takes another part number in the same brand line, so let the fit checker confirm your car before you order.
1. MOOG K500044: Front Left Lower Ball Joint for 2007-2017 Camry

- Front lower, driver side, sold singly
- Listing names 2007-2017 Camry
- Also lists 2005-2018 Avalon, Lexus ES350
- Matching right side is MOOG K500043
MOOG K500044 is a front lower ball joint for the driver side. The Amazon listing names the Toyota Camry from 2007 to 2017, which covers two full generations, along with the 2005 to 2018 Avalon, the 2007 to 2018 Lexus ES350 and the 2013 to 2018 ES300h. The passenger side uses a separate part, MOOG K500043, so a two-sided job takes one of each.
MOOG is part of DRiV, and the listing describes the joint as a suspension pivot built to restore steering stability and handle everyday road stress. The brand’s general ball joint features, such as its boot and bearing designs, are explained on MOOG’s own site, though not every part number carries every feature. Check the listing photos and the box for the hardware and any grease fitting before you start.
This joint suits owners keeping a high-mileage Camry or Avalon on the road who want a well-known replacement brand. Lower joints on these cars take the brunt of pothole hits, and a worn one shows up as a clunk over bumps or a vague feel on center. Engine and trim can change the part number, so confirm your exact model, year and engine in Amazon’s fit checker before ordering.
2. TRW JBJ1151: Front Lower Ball Joint for 2012-2015 Civic and ILX

- Front lower, sold singly
- Listing names 2012-2015 Civic
- Also lists 2013-2015 Acura ILX
- 500K-cycle endurance testing per TRW
TRW JBJ1151 is a front lower ball joint, and its Amazon listing names the Honda Civic from 2012 to 2015 and the Acura ILX from 2013 to 2015. That is the ninth-generation Civic, a car that is still common on commuter routes. Each order is a single joint, so plan on two if you want to do both sides together.
TRW says every part goes through four levels of testing and technical review before approval, including endurance testing of 500,000 cycles. The listing describes a low-friction design meant to bring steering and suspension back to their original feel, and dust covers made from high-quality rubber to keep water and grit out. TRW also supplies factory parts to carmakers, so the joint follows an OE-style layout.
On the Civic, the lower ball joint is commonly pressed into the steering knuckle and held with a snap ring, so you will need a ball joint press and the right adapters, or a shop with one. This joint suits owners who want a sealed, factory-style replacement rather than a greasable upgrade. Use the listing’s Confirmed Fit option to check your trim, since performance and special versions can differ.

3. MOOG K500227: Front Lower Ball Joint for 2010-2017 Equinox and Terrain

- Front lower, sold singly
- Listing names 2010-2017 Equinox
- Also lists 2010-2017 GMC Terrain
- Replaces GM 19258791 and 25872808
MOOG K500227 is a front lower ball joint for General Motors’ compact crossovers. The Amazon listing names the Chevrolet Equinox and GMC Terrain from 2010 to 2017, and it lists GM part numbers 19258791 and 25872808 among the numbers it replaces. One joint comes per order, so a two-sided repair needs two.
These crossovers are often fixed by swapping the whole lower control arm, because the factory joint comes attached to the arm. A separate joint like this one gives you another route when the arm and its bushings are still in good shape. Read the listing and the included instructions to see how the joint attaches, and check whether the bushings are cracked before you decide which repair makes more sense.
The listing describes the joint as a key pivot in the suspension, built to handle road stress and restore steady steering. It suits owners who drive an Equinox or Terrain through rough winter roads and want a known brand at the corner that takes the most impact. Engine and drivetrain options vary across these years, so confirm your exact vehicle in Amazon’s fit checker before you buy.
4. Mevotech Supreme: Greasable Ball Joint for CR-V, RDX and HR-V

- Patented sintered bearings
- 180-degree SAE grease fitting
- Slotted castle nut and cotter pin included
- Listing names CR-V, RDX and HR-V
This Mevotech Supreme ball joint is listed for the Honda CR-V from 2007 to 2009 and 2012 to 2016, the Acura RDX from 2007 to 2018 and the Honda HR-V from 2016 to 2021. The listing title does not state the position, so check the side and axle in Amazon’s fit checker before ordering. Supreme is one of Mevotech’s chassis part lines.
Mevotech says its patented sintered bearings give longer-lasting performance, and the joint includes a 180-degree SAE grease fitting so it can be serviced. The ball stud uses a larger, application-specific sphere, and a protective surface treatment is meant to resist rust. A part-specific slotted castle nut and cotter pin come in the box, which saves a trip back to the parts counter.
The grease fitting is the main reason to choose this joint. A few pumps at each oil change push old grease and road moisture out of the bearing, which helps in places where brine sits on the roads all winter. If no one will grease it, the feature adds little. Honda lower joints are commonly pressed in, so plan for a press and the correct adapters.
View Mevotech Supreme on Amazon

5. TRW JBJ937: Front Lower Ball Joint for 2003-2007 Accord and TSX

- Front lower, sold singly
- Listing names 2003-2007 Accord
- Also lists 2004-2008 Acura TSX
- Rubber dust cover, low-friction design
TRW JBJ937 is a front lower ball joint, and the Amazon listing names the Honda Accord from 2003 to 2007 and the Acura TSX from 2004 to 2008. Plenty of seventh-generation Accords are still running, and many of them are on their original lower joints. Each order is one joint, so a full front job takes two.
Like the rest of TRW’s line, this part goes through four levels of testing and audit review, including a 500,000-cycle endurance test, according to the listing. A low-friction design is meant to bring back the original steering feel, and the dust cover uses high-quality rubber for longer life. The joint follows a sealed, OE-style layout without a grease fitting, which keeps the repair close to factory.
The lower joint on this Accord is commonly pressed into the knuckle and retained by a snap ring, so you need a ball joint press with the right adapters. This listing suits owners planning to keep an older Accord for years who want a factory-style replacement from an OE supplier. Coupe, sedan and V6 versions can differ, so check your trim with the listing’s Confirmed Fit option before ordering.
6. Detroit Axle Front Lower Ball Joints: Pair for 2013-2017 Accord and TLX

- Two front lower joints in one kit
- Listing names 2013-2017 Accord
- Also lists 2015-2020 Acura TLX
- 10-year warranty per the listing
This Detroit Axle kit holds two front lower ball joints, one for each side. The Amazon listing names the Honda Accord from 2013 to 2017 and the Acura TLX from 2015 to 2020. Buying both joints in one order makes sense when the car has high miles, since the second side has seen the same roads as the first.
Detroit Axle says its suspension parts go through impact, wear and fatigue testing for quality and durability, and the listing states a 10-year warranty. The brand sells parts for both foreign and domestic cars, trucks and SUVs, often as pairs or full kits. Read the listing photos to see what hardware comes with each joint before the car goes up on stands.
This kit suits owners who want to do both sides at once and get one alignment for the whole job. It is a practical choice for a commuter Accord that has started to clunk or wander, as long as the knuckles and control arms are still in good shape. Confirm your year, trim and engine in Amazon’s fit checker, since the ninth-generation Accord had several versions.
View Detroit Axle Front Lower Pair on Amazon
Which Listing Fits Which Car
Use this table to match the best ball joints above to your car, then check the exact part against your vehicle.
| Vehicle | Listing | Position | Good fit for |
|---|---|---|---|
| Camry 2007-2017 | MOOG K500044 | Front left lower | High-mileage commuter sedans |
| Civic 2012-2015 | TRW JBJ1151 | Front lower | Owners who want an OE-style sealed joint |
| Equinox 2010-2017 | MOOG K500227 | Front lower | Crossovers on rough winter roads |
| CR-V 2007-2009, 2012-2016 | Mevotech Supreme | Confirm in fit checker | Owners who like to grease the front end |
| Accord 2003-2007 | TRW JBJ937 | Front lower | Older Accords kept for the long run |
| Accord 2013-2017 | Detroit Axle pair | Front lower, both sides | Doing both sides in one order |
Most of these are sold as a single joint, so a two-sided job needs two orders or a pair listing. If one side has failed on a car with high miles, the other side is usually close behind.

Potholes, Salt Spray and Ball Joint Wear Around Grand Rapids
Freeze-thaw cycles open potholes every spring here, and a hard hit loads the lower ball joint more than almost any other part. Our article on signs of pothole damage lists what to check after a bad one.
Brine is the slower threat. Salt water that gets past a cracked boot rusts the stud and washes out grease, and the joint wears from the inside. A greasable joint lets you flush that moisture out, but only if someone actually greases it.
A knock over bumps can come from a ball joint, a sway bar link or a worn strut mount. Our guide to a clunking noise over bumps helps narrow it down, and worn struts are covered in our roundup of shocks and struts for daily drivers.

Installing New Joints Safely, and When to Book Us
Ball joints hold the wheel to the car, so this is a steering and safety job, not a quick swap. Support the car on stands, wear eye protection when you separate the stud or run a press, and torque the nut to the factory figure before you fit a new cotter pin.
Even the best ball joints change the wheel’s position slightly once they go in. Have the alignment checked after the job, or the tires can wear unevenly within a few thousand miles.

If the joint is pressed in, rusted solid or riveted to the arm, or you would simply rather not lift the car, have it inspected. We handle suspension repair in Grand Rapids on foreign and domestic cars, from the first check to the alignment afterward.
More Buying Guides
Frequently Asked Questions
Is MOOG better than an OEM ball joint?
Not automatically. A factory joint is made to the original spec, and MOOG often adds features such as a grease fitting. For a daily driver, either works well when the part number is correct and the joint is fitted properly.
Are greasable ball joints worth it?
They are if you grease them. A few pumps at each oil change push out old grease and moisture, which helps in salt country. If nobody will service the fitting, a quality sealed joint is just as sensible.
Should I replace ball joints on both sides at once?
It isn’t required, but it often makes sense. Both sides have covered the same miles and roads, so when one fails the other is usually worn too, and one alignment covers both repairs.
Do I need an alignment after replacing a ball joint?
Yes, it’s a good idea. A new joint can shift camber or toe slightly, and a quick alignment check protects your tires and keeps the car tracking straight.
Hearing a knock from the front end or feeling the steering wander? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up a suspension check through our contact page.
Busy during the workday? Drop the car after hours at 456 Carrier St NE in Grand Rapids and leave a quick note on when the noise shows up and which corner it seems to come from.
