As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A turbocharged LS usually ends up with one big pipe after the turbo, and that pipe still needs a muffler. The best muffler for turbo LS builds matches that 3 or 3.5 inch pipe, fits the space under the car and keeps highway drone in check without adding restriction behind the turbine.
Below we explain how a turbo changes the job, how to size the muffler, and then review six universal mufflers from MagnaFlow, Flowmaster, Borla and Thrush. For a wider look at muffler types on stock engines, see our aftermarket muffler buying guide.
Quick answer
What muffler should go on a turbo LS?
Size it to the pipe after the turbo, usually 3 or 3.5 inches. A stainless straight-through muffler such as the MagnaFlow 14151 or Flowmaster FlowFX 74151 suits most single-turbo street builds. Choose a chambered Flowmaster Super 10 for more bark, or a Thrush 17635 for a mellow tri-flow tone on a 3 inch system.
Our Quick Picks
Three quick picks that cover the main sound choices for a turbo LS: a deep 3.5 inch straight-through, a calmer 3.5 inch straight-through and an aggressive 3 inch chambered muffler. All six are reviewed below.

MagnaFlow 14151
A full-size 3.5 inch oval case with a smooth, deep tone.

Flowmaster FlowFX 74151
A straight-through Flowmaster with a calmer cabin note.

Flowmaster Super 10 Series
Flowmaster's loudest chambered muffler, listed for LS swaps.
How a Turbo Changes the Muffler Job
On a naturally aspirated V8, the muffler does almost all of the sound shaping. On a turbo engine, the turbine wheel sits in the exhaust stream first and takes some energy out of each pulse, so the note that reaches the muffler is usually softer and smoother. That is why many turbo LS owners can run a freer-flowing muffler than they would on the same engine without boost.
Flow still matters. Everything after the turbine is pipe the exhaust has to push through, and a cramped, restrictive muffler adds back pressure on the turbo side. Most single-turbo LS kits feed one pipe of roughly 3 to 4 inches, while twin-turbo setups often keep two smaller pipes, so check how your system is laid out before you shop.
The usual complaint on boosted LS cars is drone, a steady boom in the cabin at highway rpm. When you weigh the best muffler for turbo LS cruising, a larger case or a packed straight-through core helps most.
Sizing: Pipe Diameter, Layout and Body Length
Write down four measurements before you order, since look-alike mufflers are sold in many sizes under different part numbers.
- Pipe diameter: measure the outside of the pipe that will feed the muffler. Turbo LS systems are usually 3 or 3.5 inches.
- Inlet and outlet position: center/center suits a pipe that runs down the middle of the tunnel, while offset inlets help where the pipe sweeps to one side.
- Case shape: an oval case sits lower than a round one.
- Overall length: count both necks, since the pipe has to be cut to suit and the case must clear crossmembers and the fuel tank.
Best Muffler for Turbo LS Swaps: The Six Picks
All six are universal mufflers with a 3 or 3.5 inch inlet, listed on Amazon US. None is made for one car, so a shop has to cut and weld it in; confirm size and layout on the listing first.
1. MagnaFlow 14151: 3.5 Inch Center/Center Stainless Straight-Through Muffler, 5x8x14 Oval

- 3.5 in center inlet and center outlet
- Stainless steel 5 x 8 x 14 in oval case
- Straight-through perforated core
- Two-stage acoustic packing
The MagnaFlow 14151 is a universal straight-through muffler with a 3.5 inch center inlet and a 3.5 inch center outlet. Its stainless oval case measures 5 by 8 by 14 inches, which gives a big single-turbo pipe a muffler that matches its diameter instead of necking it down. For many turbo LS swaps that run one 3.5 inch pipe from the downpipe back, it is a natural first look.
For a boosted LS, the appeal is a straight perforated core inside, wrapped in two layers of sound packing. MagnaFlow says this keeps exhaust velocity up while producing a smooth, deep tone, and it describes the design as dyno tested for flow. A free path behind the turbine is what most boosted engines want, and the packing absorbs much of the rasp that a bare pipe makes. The listing notes it is made in the USA with a limited lifetime construction warranty.
Because it is universal, the muffler can be placed and turned to suit the space under your car, but MagnaFlow recommends professional installation. The 5 inch case height needs real floor clearance, so measure the tunnel first on a low car. Offset versions are separate part numbers, so confirm that center in and center out lines up with your pipe.
View MagnaFlow 14151 on Amazon
2. Flowmaster FlowFX 74151: 3.5 Inch Center Inlet/Outlet Straight-Through Muffler, 409S Stainless

- 3.5 in center inlet and outlet
- Fully welded 409S stainless steel
- High-flow straight-through design
- Moderate exterior, mild to moderate interior tone
Flowmaster’s FlowFX 74151 is a straight-through muffler with a 3.5 inch center inlet and a 3.5 inch center outlet. It is a different design from the chambered Flowmasters many V8 owners know, and Flowmaster lists its sound as a moderate exterior performance tone with a mild to moderate interior tone. That combination suits a turbo LS that sees long highway runs as well as weekend drives.
The case is fully welded bright 409S stainless steel, which Flowmaster says is chosen for looks and long life. Inside, high-temperature sound absorption material surrounds the straight-through path, giving sound control without forcing exhaust through chambers. On a turbo engine, where the turbine has already softened the pulses, a packed straight-through muffler like this one is a common way to keep flow up and the cabin calm.
This is a universal part, so the pipe will need cutting and the muffler welded or clamped in place by someone with the right tools. Check the case length against the space you have before ordering. Drivers who want a louder, sharper bark will find it in the chambered Super 10 further down this list, while this one stays at the gentler end.
View Flowmaster FlowFX 74151 on Amazon

3. Borla XR-1 Sportsman 40945: 3.5 Inch Center/Center T-304 Stainless Racing Muffler, 12 Inch Body

- 3.5 in center inlet and center outlet
- T-304 stainless steel, made in USA
- 4.25 x 7.88 in oval, 12 in body, 17 in overall
- Reversible, un-notched weld-in necks
Borla’s XR-1 Sportsman 40945 is a universal muffler with a 3.5 inch center inlet and a 3.5 inch center outlet. Borla lists it as a racing muffler, and its oval body is 4.25 by 7.88 inches with a 12 inch body and a 17 inch overall length. That compact size is the main reason to choose it on a swap car, where a transmission crossmember, driveshaft or fuel tank often leaves little room for a longer case.
The muffler is made from T-304 stainless steel, one of the most corrosion resistant grades used in exhaust work. That counts for a lot on a car that sees salted roads, because the case and necks can outlast cheaper coated steel by years. The design is reversible, so either end can face the engine, which simplifies routing on a custom turbo system where the pipe may enter from either direction.
The necks are un-notched because Borla designs the 40945 for weld-in installation, so plan on a welder rather than clamps. A short racing muffler on a large pipe will usually be louder than a long, packed street muffler, so it suits a weekend or track-leaning build more than a quiet commuter. Confirm the dimensions on the listing before you cut.
View Borla XR-1 Sportsman 40945 on Amazon
4. Borla ProXS 40359: 3 Inch Offset Inlet/Center Outlet T-304 Stainless Muffler, 14 Inch Body

- 3 in offset inlet, 3 in center outlet
- T-304 stainless steel, all welded
- 14 in body, 19 in overall length
- Reversible design, un-notched necks
The Borla ProXS 40359 is a universal performance muffler with a 3 inch offset inlet and a 3 inch center outlet. It has a 14 inch body and a 19 inch overall length, and the offset inlet helps where the turbo pipe runs along one side of the tunnel before it reaches the muffler. On many 3 inch turbo LS systems, that layout saves an extra bend.
Borla builds the ProXS from T-304 stainless steel with all-welded construction, and lists it as made in the USA. Stainless of this grade resists the brine and road salt that rot mild steel mufflers from the bottom seam up, which is a real benefit on a project car that may stay on the road through a Michigan winter. Because the design is reversible, the offset end can be turned to suit your routing.
The un-notched necks are meant for weld-in installation. If you clamp it instead, Borla says to use 3 inch wide band clamps, part 18006, rather than U-bolt clamps that crush the pipe. Measure the 19 inch overall length against your space and confirm that your pipe is 3 inch, not 3.5, before ordering, since Borla sells many ProXS sizes.
View Borla ProXS 40359 on Amazon

5. Flowmaster Super 10 Series 843015: 3 Inch Center In/Center Out Chambered Muffler, 409 Stainless

- 3 in center inlet and center outlet
- 409 stainless steel, fully MIG-welded
- Delta Flow chambered design
- Short case for custom builds
The Flowmaster Super 10 Series 843015 is a chambered muffler with a 3 inch center inlet and a 3 inch center outlet. Flowmaster calls it its loudest and most aggressive chambered muffler, and the listing names LS swaps, muscle cars, drag cars and off-road builds among its intended uses. It is the pick here for an owner who wants the boosted V8 to be heard.
Inside is Flowmaster’s Delta Flow chambered design, which the maker says increases exhaust velocity and reduces back pressure. The case is 409 stainless steel and fully MIG-welded to handle heat and vibration, and the short case length is meant to fit a wide range of custom builds and modified exhaust setups. On a turbo engine the turbine softens the raw note somewhat, so the result is usually less harsh than the same muffler on an engine without boost.
This muffler makes no claim to be quiet, and highway drone is likely on a car that cruises at steady rpm. It is better suited to a weekend car, a drag build or a truck that does short trips than to a daily commuter. Flowmaster sells the Super 10 in several sizes, so check that the 3 inch center/center layout fits your system.
View Flowmaster Super 10 Series on Amazon
6. Thrush 17635: 3 Inch Offset Inlet/Center Outlet Tri-Flow Muffler with Mellow Performance Tone

- 3 in offset inlet, 3 in center outlet
- Tri-flow design with fiberglass matting
- Aluminized-coated shell, spun lock heads
- Reversible flow, 4.25 x 9.75 in oval body
The Thrush 17635 is a tri-flow turbo-style muffler with a 3 inch offset inlet and a 3 inch center outlet. Thrush lists it with a mellow performance tone and a 4.25 by 9.75 inch oval body. Note that turbo-style describes the internal layout, three flow paths through the case, and has nothing to do with turbochargers, but the softer note works well behind a boosted LS that does not need to be loud.
Fiberglass matting inside the case absorbs unwanted interior resonance, according to Thrush, which helps on a car that spends time at highway speed. The shell is 100 percent aluminized-coated steel with spun lock heads, and the flow direction is reversible for custom installs. Aluminized steel costs less than stainless but will not last as long on salted roads, so this suits a summer car or a budget build.
The tri-flow path is more restrictive than a straight-through core, so it fits a milder turbo setup better than a high-boost build chasing every bit of flow. Thrush notes that universal fitment may require fabrication or welding, and it offers this style in 2.25, 2.5 and 3 inch sizes, so confirm this exact 3 inch listing matches your pipe. The listing gives a 90-day limited warranty.
The Six Mufflers Side by Side
For each best muffler for turbo LS pick in this table, the sound notes are the makers’ own words, and the real result depends on the turbo, pipe size and whether a resonator stays in the system.
| Muffler | Inlet / outlet | Build | Sound, as listed |
|---|---|---|---|
| MagnaFlow 14151 | 3.5 in center / center | Stainless, 5 x 8 x 14 in oval | Deep, smooth |
| Flowmaster FlowFX 74151 | 3.5 in center / center | 409S stainless, straight-through | Moderate outside, mild to moderate inside |
| Borla XR-1 40945 | 3.5 in center / center | T-304 stainless, 12 in body | Racing muffler, compact |
| Borla ProXS 40359 | 3 in offset / center | T-304 stainless, 14 in body | Performance, reversible |
| Flowmaster Super 10 | 3 in center / center | 409 stainless, chambered | Loudest, most aggressive Flowmaster |
| Thrush 17635 | 3 in offset / center | Aluminized, tri-flow | Mellow performance tone |

Michigan Rules and Road Salt
Michigan’s Vehicle Code is plain about mufflers. The text of MCL 257.707 says a motor vehicle “shall at all times be equipped with a muffler in good working order and in constant operation to prevent excessive or unusual noise and annoying smoke,” and that a person shall not “remove, destroy, or damage any of the baffles contained in the muffler.” Thrush shows its turbo and tri-flow cases on its muffler range page.
The same section also calls for “a properly operating exhaust system which shall include a tailpipe and resonator on a vehicle where the original design included a tailpipe and resonator.” On a street-driven swap car, plan a real muffler and tailpipe into the build. We don’t recommend straight pipes, cutouts or removing emissions parts on any car that sees public roads.

West Michigan winters are the other test. A turbo pipe runs hot, but brine and slush still collect on the muffler case, and short trips leave water inside it. T-304 stainless holds up best, 409 stainless resists rust well though it can discolor, and aluminized steel is the budget choice that wears first. Our guide to the best rust remover for exhaust parts covers clean-up on older pipes and clamps.
Getting a Universal Muffler Fitted Right

Every muffler on this list is a weld-in universal part, and big 3.5 inch pipe is not easy to bend or seal in a driveway. A turbo exhaust also moves with the engine, so hangers, a flex section and clean welds matter more than on a stock car.
Watch for leaks ahead of the muffler, such as ticking at the downpipe or exhaust smell in the cabin, and read our page on exhaust leak symptoms if you notice them. A product from our exhaust repair kit roundup can hold a small leak briefly, but it is no fix for a boosted engine.
Our exhaust repair in Grand Rapids covers mufflers, pipes and hangers on foreign and domestic vehicles. Bring the measurements or the car, and we can help match a muffler to your pipe size and space.
More Buying Guides
Frequently Asked Questions
Does a turbo LS need a muffler at all?
On the street, yes. The turbo softens the exhaust note, but it is not a muffler, and Michigan’s MCL 257.707 requires a muffler in good working order on a motor vehicle. A muffler also cuts the drone that a big open pipe makes at cruise.
Should I use a 3 inch or 3.5 inch muffler?
Match the pipe that leaves your turbo. Many single-turbo LS kits use 3.5 inch pipe, while smaller kits and twin setups often use 3 inch. Measure the outside of the pipe and buy a muffler with that inlet size.
Is a straight-through or chambered muffler better on a turbo car?
Straight-through mufflers with packing are the usual choice, since they flow freely and tend to stay calmer at cruise. Chambered mufflers sound sharper and louder. Both work behind a turbo, so the decision mostly comes down to the tone you want.
Finishing a boosted LS and want the exhaust done once? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or set up an exhaust visit through our contact page.
Work hours not lining up with yours? Park the car with us after closing through the after-hours drop-off at 456 Carrier St NE, Grand Rapids, so it is waiting for us when the shop opens.
