As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
A pickup asks more of its exhaust than a sedan does. The best muffler for trucks has to sound right at idle, stay calm on a long highway pull, clear rocks or ruts and survive years of salt spray. For most owners that means a complete cat-back kit built for the exact truck rather than a single can welded into the stock pipe.
This hub uses four reference trucks: the Toyota Tundra, Toyota Tacoma, Nissan Titan and Chevrolet Colorado (with its GMC Canyon twin). If you would rather fit a universal muffler, our guide to choosing an aftermarket muffler covers sizes and tone in more depth.
Quick answer
What muffler setup works well on a pickup truck?
A bolt-on stainless cat-back kit made for your truck is the easiest choice. MagnaFlow’s 15306 Street Series suits 2014-2021 Tundras, Borla’s 140680 suits 2016-2023 Tacoma 3.5L trucks and MBRP’s S5090304 covers newer Colorado and Canyon pickups. Confirm year, cab, bed and engine on Amazon before ordering.
Our Quick Picks
Three quick picks, one each for the Tundra, the newer Tacoma and the Colorado or Canyon. All six kits are reviewed below.

MagnaFlow 15306 Street Series
A moderate-tone stainless cat-back built for the second-generation Tundra.

Borla 140680
A stainless Borla cat-back sized for the third-generation Tacoma V6.

MBRP S5090304
A single side exit stainless cat-back for the second-generation Colorado and Canyon.
Cat-Back Kit or a Muffler Swap?
A cat-back system replaces everything behind the catalytic converters: the intermediate pipe, the muffler, the tailpipe and usually the tip. Because the kit is bent to match one truck’s frame and hanger points, it bolts in with clamps instead of cutting and welding. That matters on a pickup, where long pipes and a spare tire make custom routing slow.
A muffler-only swap costs less in parts, but a shop has to cut out the factory can and weld the new one to pipe that may already be thin after a few Michigan winters. That is why the best muffler for trucks with rusty stock pipe usually comes as a full kit, and none of these kits touch the converters.
Pipe Size, Exit Style and Highway Drone
V8 trucks like the Tundra and Titan move more exhaust, so 2.5 inch dual pipes or a single 3 inch pipe suit them. A V6 Tacoma or Colorado can run a 3 inch single pipe, but a much larger pipe than stock on a small engine tends to sound hollow rather than deep. A V6 truck usually sounds best with a moderate muffler, while a V8 can carry a more aggressive one.
A side exit keeps the tip clear of a trailer hitch, and a dump exit tucks up for clearance off road. Drone, the steady cab hum at cruise, is the usual complaint after a swap, so read the maker’s interior sound description before choosing a loud kit.
Best Muffler for Trucks: Six Bolt-On Cat-Back Kits Reviewed
Each pick below is a specific Amazon US listing made for a named truck, with the fitment stated in the listing. Cab style, bed length and engine all change which kit fits, so check those three details on Amazon before you buy.
1. MagnaFlow 15306 Street Series: Stainless Dual Cat-Back for 2014-2021 Toyota Tundra

- Listed for the 2014-2021 Toyota Tundra
- Dual same side exit behind passenger rear tire
- Stainless steel, mandrel bent pipe
- Bolt-on, moderate Street Series sound
MagnaFlow’s 15306 is a complete cat-back system from the Street Series, and the listing says it is designed for the 2014-2021 Toyota Tundra. It routes both tailpipes to the same side, exiting behind the passenger rear tire, which leaves the area under the hitch clear for towing. The Tundra comes in several cab and bed combinations, so confirm yours against the listing before you order.
MagnaFlow places the Street Series in the moderate sound range. The aim is a stronger outside tone and a little more power while keeping interior noise comfortable, which suits a truck that spends hours on the highway. MagnaFlow says the series pairs mandrel bent pipes with larger or straighter-through mufflers to cut restriction, and the listing says the system is 50-state legal and tuned around the factory calibration. Stainless construction is a real asset on a truck that sees brined roads every winter.
The kit bolts on in place of the factory parts behind the catalytic converters, and MagnaFlow says it uses 3D scanning during development so the system lines up with the original mounts. It is not the pick for anyone after a loud, aggressive note, and a split rear exit needs a different listing.
View MagnaFlow 15306 Street Series on Amazon
2. Borla 140680: T-304 Stainless Cat-Back for 2016-2023 Toyota Tacoma 3.5L V6

- Listed for 2016-2023 Tacoma 3.5L V6, 2WD and 4WD
- T-304 stainless steel
- All welded, bolt-on installation
- Made in USA, classic Borla sound
Borla’s 140680 is a cat-back system for the 2016-2023 Toyota Tacoma with the 3.5L V6, in two-wheel and four-wheel drive with automatic or manual gearboxes. The listing names the extended cab with the 6 foot 1 inch bed and the crew cab with the 5 foot 1 inch bed, both on the 127.4 inch wheelbase. The crew cab with the 6 foot 1 inch bed on the 140.6 inch wheelbase needs Borla adapter 60593, so check your wheelbase first.
The system is made from T-304 stainless steel, the grade Borla is known for, and it uses all welded construction rather than a pile of slip joints and clamps. That matters in West Michigan, where salt eats lower-grade steel fast. It is made in the USA and installs as a bolt-on kit using the factory mounting points.
Borla describes the tone simply as the classic Borla sound. On a V6 Tacoma, a matched system keeps the note fuller than a big universal muffler would. The listing gives few other details, so read the full Amazon page for tip and exit style before ordering. It does not fit the 2024 and later Tacoma, which uses a different chassis.

3. MBRP S5090304: 3 in T-304 Single Side Exit Cat-Back for 2017-Up Colorado and Canyon

- Listed for 2017-up Colorado and Canyon 2.5L and 3.6L
- Mandrel-bent 3 in tubing
- T-304 stainless, with T-304 tip
- Bolt-on, drone-free performance tone as listed
The MBRP S5090304 is a 3 inch cat-back system with a single side exit. The listing names the 2017 and later Chevrolet Colorado and GMC Canyon with either the 2.5L four-cylinder or the 3.6L V6, and MBRP’s S5090304 product page calls it a Tour Profile system. Gas engines only: the diesel Colorado uses a different setup.
Construction is T-304 stainless steel, including the tip, and the tubing is mandrel bent so the pipe keeps a full 3 inch diameter through each bend. MBRP lists the sound as a drone-free performance tone, which suits a midsize truck that does daily commuting as well as weekend trips. A side exit ahead of the rear tire also keeps the tip away from a hitch.
The kit is a bolt-on install using the factory hanger points. Owners of the 2015 and 2016 trucks, or the redesigned 2023 and later models, should look for a different part number, since the listing is written around the second generation from 2017. Check engine, cab and bed length on the Amazon page before ordering, and plan to reuse or replace the rubber hanger isolators if they are cracked.
4. Flowmaster 717985 FlowFX Extreme: 3 in 409 Stainless Dump Exit Cat-Back for 2004-2015 Nissan Titan

- Listed for 2004-2015 Nissan Titan 5.6L
- 3.00 in mandrel bent 16-gauge tubing
- 409 stainless steel construction
- Dump style exit for ground clearance
Flowmaster’s 717985 FlowFX Extreme is a cat-back exhaust for the first-generation Nissan Titan with the 5.6L V8, covering 2004 to 2015 trucks. It uses a single 3.00 inch pipe and a dump style exit that points the exhaust down toward the ground instead of running a tailpipe to the bumper. Flowmaster says the dump exit improves ground clearance in extreme off-road conditions, so the tip is less likely to snag on rocks or ruts.
The tubing is 16-gauge, mandrel bent stainless, and the whole system is 409 stainless steel for better long-term corrosion resistance than aluminized pipe. Flowmaster lists gains of up to 16 hp and 23 lb-ft of torque over stock at the rear wheels. The FlowFX muffler is described as giving an aggressive to moderate sound level, louder than the Street Series style kits on this page.
Hardware is included and the hangers sit in the stock locations, which helps on a truck that is already more than a decade old. A dump exit throws exhaust under the truck rather than behind it, so it is a poor match for anyone who spends time parked with the engine running near the bed.
View Flowmaster 717985 FlowFX Extreme on Amazon

5. Borla 140796: True Dual T-304 Stainless Cat-Back for 2016-2023 Nissan Titan 5.6L V8

- Listed for 2016-2023 Titan 5.6L V8, 2WD and 4WD
- True dual system
- T-304 stainless, all welded
- Bolt-on, made in USA
Borla’s 140796 is a cat-back exhaust for the second-generation Nissan Titan with the 5.6L V8, model years 2016 to 2023. The listing names the Crew Cab with the 5 foot 7 inch short bed and the extended cab with the 6 foot 5 inch standard bed, both on the 139.8 inch wheelbase, in two-wheel or four-wheel drive. Borla says the system is a true dual, so each bank of the V8 gets its own pipe all the way back.
Like the Tacoma kit above, it is built from T-304 stainless steel with all welded construction, and it is made in the USA. A true dual layout tends to give a V8 a fuller, more even note than a single pipe, and Borla lists the tone as its classic sound. Stainless pipe and welded joints help the system hold up through years of Michigan salt.
The system installs as a bolt-on kit in place of the factory parts behind the converters. Check the listing carefully if you drive a Titan XD, since the longer XD chassis is a separate model, and confirm cab and bed length too. It is not a kit for owners who want the cab as quiet as stock.
6. Flowmaster 717971 FlowFX Extreme: 3 in 409 Stainless Cat-Back for 2005-2015 Toyota Tacoma 4.0L V6

- Listed for 2005-2015 Toyota Tacoma 4.0L V6
- 3.0 in 16-gauge mandrel bent tubing
- 409 stainless steel construction
- Dump style exit, factory hanger locations
The Flowmaster 717971 FlowFX Extreme is a cat-back system for the second-generation Toyota Tacoma with the 4.0L V6, covering 2005 to 2015. It runs a single 3.0 inch pipe and finishes in a dump style exit, which Flowmaster says helps ground clearance in extreme off-road use. That makes it a natural fit for a Tacoma that spends weekends on two-tracks and state forest roads.
The tubing is 16-gauge mandrel bent stainless steel, and the system is built from 409 stainless for extra durability and better long-term corrosion resistance. Flowmaster describes the FlowFX muffler as giving a deep, powerful sound along with increased performance, so expect a stronger note than a stock or Street Series style system. It uses the factory hanger locations and includes the hardware for an at-home install.
Older Tacomas often have rusted factory clamps and bolts, so the removal can take longer than the new parts. Confirm the cab and bed on your truck, since the second generation came in several lengths. Owners who want a quiet cab on long highway trips may prefer one of the moderate kits above instead.
View Flowmaster 717971 FlowFX Extreme on Amazon
Six Truck Exhaust Kits Side by Side
| Kit | Truck as listed | Pipe and exit | Material |
|---|---|---|---|
| MagnaFlow 15306 Street Series | 2014-2021 Toyota Tundra | Dual, same side behind passenger rear tire | Stainless steel |
| Borla 140680 | 2016-2023 Toyota Tacoma 3.5L V6 | Single, bolt-on | T-304 stainless |
| MBRP S5090304 | 2017-up Colorado and Canyon 2.5L/3.6L | 3 in, single side exit | T-304 stainless |
| Flowmaster 717985 FlowFX Extreme | 2004-2015 Nissan Titan 5.6L | 3 in, single dump exit | 409 stainless |
| Borla 140796 | 2016-2023 Nissan Titan 5.6L V8 | True dual, bolt-on | T-304 stainless |
| Flowmaster 717971 FlowFX Extreme | 2005-2015 Toyota Tacoma 4.0L V6 | 3 in, dump exit | 409 stainless |
For a truck that tows or commutes, the best muffler for trucks is usually the moderate one: the MagnaFlow, the MBRP or either Borla. Trail trucks that drag over rocks benefit from the Flowmaster dump exits. Sibling guides cover the 5.3 Silverado muffler choices, Ram 1500 exhaust options and Ford V10 mufflers.

Michigan Muffler Rules and Salt on a Work Truck
Section 257.707 of the Michigan Vehicle Code says a motor vehicle must at all times have a muffler in good working order and in constant operation to prevent excessive or unusual noise and annoying smoke. It also says no one may remove, destroy or damage the baffles in a muffler, and it bans muffler cutouts and bypasses on motorcycles and mopeds. A properly working exhaust system, with a tailpipe and resonator where the original design had them, is required too.
Every kit here keeps a real muffler in the system. We do not recommend straight pipes, cutouts or removing catalytic converters on any street truck.

Grand Rapids roads are brined for months, and short trips leave water in the muffler that never boils off, so rust starts at the seams and clamps. T-304 stainless resists that best, then 409 stainless, then aluminized steel. Our guide to how long an exhaust system lasts explains the wear points.
When a Truck Exhaust Job Belongs in the Shop
Bolt-on kits are made for home installs, but factory clamps and hanger bolts on an older truck are often rusted solid, and that work is easier on a lift. If the stock system already rattles or sags, check for a broken exhaust hanger before you order parts.

A leak ahead of the muffler is more than noise, because fumes can reach the cab. Learn the signs of an exhaust leak, and use an exhaust repair kit only as a stopgap for a small crack until the truck is booked in.
Our team handles exhaust repair in Grand Rapids on foreign and domestic trucks, from a single hanger to a full cat-back install. We can also check that the kit you picked matches your truck’s cab and bed.
More Buying Guides
Frequently Asked Questions
Is a cat-back exhaust better than a new muffler on a truck?
A cat-back kit replaces the pipe, muffler and tip as one matched set that bolts to the factory hangers, so it suits trucks with rusty stock pipe. A muffler-only swap is cheaper in parts but has to be cut and welded in by a shop.
Which muffler suits a V6 truck?
A moderate muffler in a kit made for the truck usually works best on a V6, because an aggressive muffler can make a six-cylinder sound raspy. Kits such as the Borla 140680 for the Tacoma 3.5L and the MBRP S5090304 for the Colorado and Canyon are built around those engines.
Will a performance muffler drone in my truck?
Some do, mostly at steady highway speed. Kits the maker describes as moderate or drone-free, a stock-size pipe and tight hangers all help keep the cab quiet, so check the sound description on the listing before you choose.
Can I fit these mufflers on a diesel truck?
No. The kits on this page are made for gas engines, and diesel pickups use their own systems designed around the diesel particulate filter. Never remove a DPF or converter to fit a louder exhaust.
Found the kit for your pickup and want it fitted without leaks or rattles? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or book a truck exhaust install on our contact page.
Working the same hours we do? Bring the truck to 456 Carrier St NE after we close, use the after-hours drop-off, and we will get to it once the doors open.
