As an Amazon Associate, 456 AutoFix earns from qualifying purchases. Product links below go to Amazon, where you can confirm the right part for your vehicle.
Honda builds the Civic, Accord and CR-V in huge numbers, and each generation hangs its exhaust a little differently. So the best muffler for Honda owners is never one part: it is the listing that names your model, year and engine, with a tone you can live with on the commute.
Below, we split quiet factory-style repairs from bolt-on performance kits and review six options that state their fit. For chambered, turbo and straight-through designs in general, see our guide to aftermarket mufflers.
Quick answer
Which muffler should a Honda get?
Match the generation first. A 2017-2021 Civic 1.5L takes MagnaFlow’s 19373 cat-back, a 2018-2022 Accord Sport 4-cylinder suits Borla’s 140786, and a 2007-2009 CR-V with a rotted rear section gets Walker’s Quiet-Flow SS 54749 for a quiet, factory-style repair. Older Civics and the V6 Accord have their own kits below.
Our Quick Picks
Three quick picks for the most common Honda setups: a 10th-generation Civic, a current Accord Sport and a CR-V that needs a quiet repair. All six are reviewed below.

MagnaFlow 19373 Street Series
A stainless kit with MagnaFlow's resonant Street Series tone.

Borla 140786 Cat-Back
Bolt-on stainless system that keeps the factory tips.

Walker Quiet-Flow SS 54749
Factory-style sound in a fully stainless body.
Start With the Model, Generation and Exit Layout
Honda exhaust parts are sorted by vehicle, not by brand loyalty. Two Civics from the same year can need different kits because a sedan, coupe and hatchback route the tailpipe to different spots. Before you shop, note these details from the car itself or the registration:
- Model year and generation: the 2006-2011 Civic, the 2012-2015 Civic and the 2016-2021 Civic each have their own pipe shape and hanger points.
- Engine: a 1.5L turbo, 1.8L, 2.0L or 3.5L V6 changes pipe diameter and muffler size.
- Exit layout: look under the bumper. Single right side, dual split (one tip each corner) and dual center exits are not interchangeable.
- Trim and body style: some kits list one trim only, such as the Accord Sport, which uses its own rear valance and tips.
Repair Muffler or Performance Kit?
Plenty of older Hondas simply have a rear muffler that rusted through. For that car, a direct-fit replacement is the plain answer. It bolts to the factory flange and keeps the stock sound. Walker sorts its range the same way on its light vehicle muffler page, with the Quiet-Flow SS line in fully stainless steel and SoundFX as the lower-cost repair option.
A cat-back kit replaces every pipe and muffler behind the catalytic converter. An axle-back only swaps the last section with the muffler and tip. Both make sense when the pipes are already rusty or when you want a firmer note. The trade-off is drone, the low hum some kits create at highway speed, so read how each maker describes the sound.
Best Muffler for Honda: Six Listings by Model
Every pick below names the Honda it was made for. Check year, model, trim, engine and body style on Amazon before you order, since no single listing covers every Civic, Accord or CR-V.
1. MagnaFlow 19373 Street Series: Stainless Cat-Back for 2017-2021 Honda Civic 1.5L

- Listed for 2017-2021 Honda Civic 1.5L
- Dual center rear exit layout
- Stainless steel, made in the USA
- Direct-fit, developed with 3D scanning
The MagnaFlow 19373 is a Street Series cat-back system listed for the 2017-2021 Honda Civic with the 1.5L turbo engine. It replaces the pipes and muffler behind the catalytic converter and ends in a dual center rear exit, the layout found under the middle of the rear bumper. Because some Civic trims and body styles use a different exit, look under your car before ordering and match the layout to the listing.
MagnaFlow builds the system from corrosion-resistant stainless steel using CNC robotic manufacturing, and it says the kit is made in the USA. The company describes the Street Series sound as resonant and throaty, tuned for both interior and exterior levels rather than for maximum volume. It also says 3D scanning was used during development so the pipes line up with the factory hangers, which matters on a car where clearance under the rear floor is tight.
This kit suits a Civic owner whose factory exhaust is tired or who wants a firmer note with a bolt-on install. It is not the right pick for a car with a single side exit or for someone who wants the stock, near-silent sound. Confirm year, trim, body style and engine on Amazon, and note the listing’s one-year limited construction warranty.
View MagnaFlow 19373 Street Series on Amazon
2. Borla 140786: T-304 Stainless Cat-Back for 2018-2022 Honda Accord Sport 4 Cyl

- Listed for 2018-2022 Accord Sport 4 cyl
- Dual split rear exit, 2.25 inch each side
- Reuses the factory tips (not included)
- T-304 stainless, bolt-on, made in USA
The Borla 140786 is a cat-back exhaust listed for the 2018-2022 Honda Accord Sport with the four-cylinder engine. It uses a dual split rear exit, with a single 2.25 inch exit on each side, and it is designed to reuse the original tips that sit in the Sport’s rear valance. The tips are not included, so you keep the factory look while the pipes and mufflers ahead of them change.
Borla builds the system from T-304 stainless steel with all-welded construction, and the listing describes a bolt-on installation and US manufacture. The headline feature for a daily driver is the no drone guarantee printed on the listing, which speaks to the low highway hum that puts many Accord owners off aftermarket exhausts. Stainless construction also helps in a state where salt sits on the underside from November to March.
This kit suits an Accord Sport owner who wants a little more voice without a loud cabin on a long drive. It does not fit the LX, EX or V6 versions unless the listing says so, and it will not suit a car that has lost or damaged its factory tips. Confirm year, trim, engine and transmission on Amazon before buying, and check that the existing tips are in good shape.
View Borla 140786 Cat-Back on Amazon

3. MagnaFlow 16687 Street Series: Stainless Cat-Back for 2006-2011 Honda Civic 1.8L and 2.0L

- Listed for 2006-2011 Civic 1.8L and 2.0L
- Single straight passenger side rear exit
- Stainless steel, hardware included
- Limited lifetime construction warranty
The MagnaFlow 16687 is a Street Series cat-back system listed for the 2006-2011 Honda Civic with the 1.8L or 2.0L engine. It ends in a single straight tip on the passenger side, the same position as the factory exhaust on most cars from this generation. Many of these Civics are now well past 100,000 miles, and the original pipes and rear muffler are often the first parts to rot in a salt state.
MagnaFlow makes the kit from stainless steel with CNC robotic construction and says it is made in the USA. The listing states that all hardware needed for a do-it-yourself install is included, and that 3D scanning was used to get the pipes to fit like the original parts. MagnaFlow describes the sound as its resonant, throaty Street Series tone, tuned for both interior and exterior levels.
This kit suits a 2006-2011 Civic owner who would rather replace the whole system once than patch it section by section. It is less suited to a car whose only problem is the rear muffler, where a direct-fit replacement costs less effort. Confirm year, body style, trim and engine on Amazon, and check the converter flange studs before you start, because they can be badly corroded.
View MagnaFlow 16687 Street Series on Amazon
4. Borla 11828: S-Type Stainless Axle-Back for 2012-2015 Honda Civic 4 Cyl

- Listed for 2012-2015 Honda Civic 4 cyl
- Single right rear exit
- 4.25 x 3.5 inch oval polished T-304 tip
- S-Type sound, no drone guarantee
The Borla 11828 is an axle-back system listed for the 2012-2015 Honda Civic with the four-cylinder engine. An axle-back replaces only the rear section, so it swaps the muffler and tip while the pipes ahead of it stay in place. It ends in a single right rear exit with a polished T-304 stainless oval tip that measures 4.25 by 3.5 inches.
Borla rates the system with its S-Type sound and builds it from T-304 stainless steel with all-welded construction. The listing describes a bolt-on installation, US manufacture and a no drone guarantee, which matters if the car covers long highway miles. Because it is a short section, the job is usually smaller than a full cat-back, with fewer joints to free up under the car.
This option suits a ninth-generation Civic whose middle pipe and resonator are still solid but whose rear muffler is rusted or simply too quiet for the owner’s taste. It is not a fix for leaks further forward, and it will not change the sound as much as a full system. Confirm year, body style, trim and engine on Amazon, since the Civic Si and hybrid may use different exhaust parts in these years.
View Borla 11828 Axle-Back on Amazon

5. Walker Quiet-Flow SS 54749: Direct-Fit Muffler Assembly for 2007-2009 Honda CR-V

- Listed for 2007-2009 Honda CR-V
- 1.75 in inlet (OD), 2.5 in outlet (OD)
- 100% stainless steel with internal drainage
- OE-style hangers and pipe routing
The Walker Quiet-Flow SS 54749 is a direct-fit muffler assembly listed for the 2007, 2008 and 2009 Honda CR-V. It has a 1.75 inch inlet and a 2.5 inch outlet, both outside diameter, and it uses OE-style hangers, brackets and pipe routing. Walker says it bolts in without special fabrication or welding, so it goes where the factory rear section went.
Walker describes the Quiet-Flow SS line as the only broad-market muffler built entirely from stainless steel, with an internal drainage system that cuts down on trapped moisture. Louvered tubes and domed heads aim for factory-style sound, and the listing says the design is acoustic and flow tested. Internal partitions and mechanically joined tubes allow for expansion during heat cycles, which helps a muffler that sees cold starts every winter morning.
This is the pick for a CR-V owner who wants the car quiet and legal again rather than louder. It will not add any performance or tone, and it only replaces the rear muffler assembly, so a leak at the flex pipe or converter needs its own repair. Confirm the year, trim and engine on Amazon, and read the qualifier notes. Walker backs it with a limited lifetime warranty.
View Walker Quiet-Flow SS 54749 on Amazon
6. MagnaFlow 16817 Street Series: Stainless Cat-Back for 2008-2012 Honda Accord 3.5L V6

- Listed for 2008-2012 Honda Accord 3.5L
- Dual split rear exit
- Stainless steel, mandrel-bent pipes
- Listing states 50-state legal
The MagnaFlow 16817 is a Street Series cat-back system listed for the 2008-2012 Honda Accord with the 3.5L V6. It finishes in a dual split rear exit, with a tip at each corner of the bumper, and it replaces the factory parts behind the catalytic converter. MagnaFlow says it was designed specifically for this Accord, using 3D scanning so the system bolts on in the stock position.
The listing describes the sound as moderate: more exterior tone from mandrel-bent pipes and straight-through mufflers, without raising interior noise to an uncomfortable level. MagnaFlow states that the system is 50-state legal and built to work with the factory engine calibration. Construction is stainless steel with CNC robotic manufacturing, and the kit carries a limited lifetime construction warranty.
This kit suits an eighth-generation V6 Accord owner whose exhaust is rusted or who wants a fuller sound from that engine. It is not listed for the four-cylinder Accord from the same years, so check the engine before you order. Confirm year, body style, trim and engine on Amazon, and look at the converter outlet flanges, since the new system bolts to them.
View MagnaFlow 16817 Street Series on Amazon
Which Honda Takes Which Kit
Use this table to narrow the field, then confirm fit on the listing itself.
| Honda | Option here | Type | Sound (maker’s words) |
|---|---|---|---|
| 2017-2021 Civic 1.5L | MagnaFlow 19373 | Cat-back, dual center exit | Resonant, throaty |
| 2018-2022 Accord Sport 4 cyl | Borla 140786 | Cat-back, dual split, reuses OE tips | No drone guarantee |
| 2006-2011 Civic 1.8L or 2.0L | MagnaFlow 16687 | Cat-back, single right exit | Resonant, throaty |
| 2012-2015 Civic 4 cyl | Borla 11828 | Axle-back, oval tip | S-Type |
| 2007-2009 CR-V | Walker Quiet-Flow SS 54749 | Direct-fit muffler assembly | Factory-style |
| 2008-2012 Accord 3.5L V6 | MagnaFlow 16817 | Cat-back, dual split exit | Moderate |

A CR-V used for school runs is well served by the quiet Walker repair, while a Civic that doubles as a weekend toy can take a stainless cat-back. The best muffler for Honda commuters is the one that still sounds pleasant after an hour on US-131.
Salt, Clamps and the Michigan Muffler Rule
Michigan’s vehicle code, section 257.707c, requires a muffler or other noise-reducing device in good working order on any vehicle driven on a street or highway. It also bars cutouts, bypasses and similar devices. Every product in this guide replaces the factory muffler behind the converter, and we never suggest straight pipes, resonator deletes or pulling emissions parts.
Road salt is the bigger threat to a Honda exhaust in West Michigan. Slush packs into the rear bumper area, and short winter trips leave water sitting inside the muffler case. Stainless parts hold up better than aluminized steel, though the hangers and clamps around them still corrode over a few seasons.

On a slip-fit joint, a band clamp seals better than a U-bolt clamp because it does not crush the pipe, which makes the next repair easier. If your current muffler has only a small hole, our post on a hole in the muffler explains the risks, and a patch from our exhaust repair kit roundup can hold until the new part arrives. A rattle can also come from a broken exhaust hanger.
When a Shop Should Do the Swap
A bolt-on axle-back or direct-fit muffler is a fair driveway job with good jack stands and a can of penetrating oil. A full cat-back on a car that has seen ten Michigan winters is another story. Flange bolts often snap, and the converter outlet studs can need heat or drilling.
A smell of exhaust inside the cabin points to a leak ahead of the muffler, and our checklist of exhaust leak warning signs helps you find where. Do not keep driving a car with fumes in the cabin.

If you would rather not fight seized hardware, our Grand Rapids exhaust repair service fits the best muffler for Honda models along with pipes, hangers and clamps. We can check which kit fits your trim and whether the old pipes are worth keeping.
More Buying Guides
Frequently Asked Questions
Does a Civic sedan exhaust fit a Civic hatchback?
Often not. Honda changes the exit layout by body style and trim on several Civic generations, so the pipe routing and tips can differ. Check body style and trim on the listing before you order.
Will a performance exhaust make my Honda drone?
Some kits do at steady highway speed. Borla lists a no drone guarantee on its Honda systems, and MagnaFlow says its Street Series keeps interior noise at comfortable levels. A direct-fit OE-style muffler keeps the factory tone.
Is a louder Honda exhaust legal in Michigan?
A bolt-on kit with a working muffler is the normal route. Michigan’s vehicle code requires a muffler in good working order and bans cutouts, bypasses and similar devices, so straight pipes are out on the street.
Does this guide cover the Honda Click scooter?
No. The Honda Click 125i is a scooter with its own one-piece exhaust, and these car mufflers will not fit it. Look for a listing that names the Click model and engine size.
Tired of a rusty rear box on your Civic or CR-V? Call 456 AutoFix at 616-279-3832, Monday to Friday 8am to 5pm, or request a muffler appointment through our contact page, and we will fit the best muffler for Honda models that suits your car.
If the daytime slot does not work, bring the Honda by after hours and use our drop-off. The shop sits at 456 Carrier St NE in Grand Rapids, in the Creston neighborhood.
